Long-wavelength 640×486 GaAs-AlGaAs quantum well infraredphotodetector snap-shot camera

A 9-μm cutoff 640×486 snap-shot quantum well infrared photodetector (QWIP) camera has been demonstrated. The performance of this QWIP camera is reported including indoor and outdoor imaging. The noise equivalent differential temperature (NEΔT) of 36 mK has been achieved at 300 K background with f/2 optics. This is in good agreement with expected focal plane array sensitivity due to the practical limitations on charge handling capacity of the multiplexer, read noise, bias voltage, and operating temperature     

台湾功能材料产业与研究概况

本文简要地介绍目前台湾功能材料产业与研究的情况，其中包括化合物半导体、电子构装材料、电子功能陶瓷材料、高温超导体、磁记录材料、稀土永磁材料、发光材料和传感器等。     

Strain analysis of moving objects using a Fourier transform grid method

There is no good method to measure the shape and the strain distributions of a structure changing with time. We have previously proposed the Fourier transform grid method (FTGM) to measure the three-dimensional shape and surface strain distributions of stationary objects by analysing the two-dimensional grating images recorded with two cameras. In the stereoscopic method, it is very important to determine the accurate geometric parameters of the camera system. In this paper, the positions and the directions of cameras are accurately determined using the FTGM applied to images of a reference object on which a two-dimensional grating is drawn. Applications for analysing shape and strain distributions of vibrating rubber plates and a moving human skin are shown.     

钢管内径光电检测装置

介绍了一种检测细长钢管内径的光电检测装置。该装置利用线阵ＣＣＤ作传感器，采用８０３１单片机作为主控制。     

搅拌工艺对半固态Y112铝合金组织及性能的影响

采用自行研制的机械搅拌装置,研究了不同工艺参数对半固态Y112铝合金组织及性能的影响.研究表明,搅拌温度越高,搅拌速度越大,固相颗粒越细小、均匀和圆整,其抗拉强度与伸长率越高;但温度太高,固相颗粒会熔化,抗拉强度及伸长率也降低;随搅拌时间的延长,固相颗粒先变得细小、均匀和圆整,然后长大,抗拉强度、伸长率先升高后降低.     

热力学相图计算技术在闪速燃烧合成氮化硅铁中的应用

将热力学相图计算技术应用于Si-Fe-O-N体系,以评估由FeSi75粉闪速燃烧合成氮化硅铁的条件和目标产物。结果表明:将闪速燃烧温度控制在1200～1500℃之间较为适宜,此时平衡态产物中除主要含有Si3N4以外,还有一定量的Fe与Si间化合物和少量稳定的SiO2存在。此计算结果与实际试验结果吻合良好。     

有机盐聚合醇氯化钾钻井液的应用

霍尔果斯背斜构造极其复杂,内应力极高,地层倾角大,断层、破碎带多,并存在高低压互层;安集海河组的灰绿色软泥岩水化严重并具有粘弹塑性.该区块重点探井霍003井三开、四开井段选用有机盐聚合醇氯化钾钻井液,同时为保证钻井液在高密度下（2.55 g/cm^3）具有好的流变性,使用活化铁矿粉、活化重晶石加重.应用结果表明,由于采用了强抑制和多元封堵的措施,该钻井液具有良好的流变性和较强的携带能力,钻进中曾携带出重2.8 kg和5.1kg的大掉块;滤失量低,泥饼质量好,封堵能力强,造壁能力强,减轻了井下阻卡程度;有良好的储层保护能力;在室内研究的基础上,经过现场合理使用和维护钻井液,霍003井提高了机械钻速,缩短了钻井周期,井身质量优于邻井.指出在高密度下,未选出适合有机盐聚合醇氯化钾钻井液的稀释剂,钻井液流动性较差.     

Effects of various post-treatments on carbon nanotube films for reliable field emission

In this report, the FE characteristics of carbon nanotubes (CNTs) treated using both thermal annealing and mechanical coatings on the as-grown CNTs systematically studied. It was found that in the high temperature annealed samples, CNTs were attacked at its root during annealing due to a small amount of oxygen, and were pulled out of the substrate in places after FE measurements because of the contact resistance. However, for the mechanically coated samples both with spin on glass (SOG) and polymethyl methacrylate (PMMA), CNTs were found to be nearly intact after FE measurements and showed reliable FE characteristics over repeatable voltage scan. The reliability of CNTs during FE could be owing to the strong adhesion of CNTs to the substrate both by SOG and PMMA coatings.     

房屋建筑结构无损检测方法的分析与展望

通过对现有的结构无损检测方法的总结和分析,讨论了各种方法的优缺点.并结合现场测试的要求,展望结构检测技术的发展方向与趋势.