Cu/SBA-15 as adsorbent for propane/propylene separation

Samples of mesoporous silica SBA-15 were prepared under hydrothermal conditions where Cu cations were incorporated to the structure by impregnation in order to compare the adsorption behavior in the presence and absence of this element. The adsorption/desorption equilibrium isotherms of propylene, propane, and N₂ were measured to evaluate their usefulness in the propane/propylene separation. All the adsorption isotherms of SBA-15 measured in the absence of Cu cations were described by the Freundlich equation, while the adsorption isotherms of propane on Cu/SBA-15 were better represented by the Henry equation and those of propylene were satisfactorily described by the Langmuir model in the range P < 100 Torr. The adsorption uptake of propylene increased and that of propane decreased in Cu/SBA-15 as compared to the amounts observed in the SBA-15 sample. The presence of Cu atoms in the adsorbent lattice increased the selectivity towards propylene. Under some working conditions the adsorbed amount of propylene in Cu/SBA-15 sample was totally reversible and the propane uptake, negligible.     

喷雾干燥器粘壁产生的原因

引言众所周知,喷雾干燥工艺及设备是陶瓷、保护渣、化工、高岭土等行业常用的泥浆干燥设备。不管是哪个行业都或多或少存在喷雾塔体粘壁问题。此问题看似小问题,其实对使用厂会造成诸多不便,同时也造成了能源的浪费,尤其是粘性较大的泥浆原料,此问题尤为突出。     

SERCOS Ⅱ在注塑机全电动设计中的应用

针对传统注塑机在加工精度、加工效率上的不足，提出一种全电子注塑机的控制方案，介绍了基于SERCOSⅡ实时系统的运动控制方法，分析了实现注塑过程的高速高精度的硬件体系。在试验样机3个月的连续工作中，当周期循环时间为4ms，注射量最大达到80cm^3时，产品的成型周期能够控制在15s以内，注出产品的质量、精度均满足要求，表明该设计切实可行。     

Preparation of fluoroacrylate nanocopolymer by miniemulsion polymerization used in textile finishing

Latex based on fluoroacrylate (TAN) and other comonomers was prepared via miniemulsion polymerization in the presence of stearyl trimethyl ammonium chloride (STAC) and 2, 2′‐azobis (2‐amidinopropane) dihydrochloride (ABAP) as a water soluble initiator. Light transmittance studies demonstrated that the light transmittance of prepared emulsions increases with the amount of TAN, STAC, cosolvent DPM, and hydrophobe DM. Given suitable reaction temperature and quantities of TAN, STAC, DPM, and DM, a copolymer emulsion of fluoroacylate with a particle size of 50 nm was produced. The water repellency tested on polyester fabrics displayed greater effectiveness than that of commercial products with higher fluorine content. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1466–1472, 2004     

Synthesis of Dimethyl Carbonate from Methanol and Carbon dioxide using Potassium Methoxide as Catalyst under Mild Conditions

Pd-supported on WO₃–ZrO₂ (W/Zr atomic ratio=0.2) calcined at 1073 K was found to be highly active and selective for gas-phase oxidation of ethylene to acetic acid in the presence of water at 423 K and 0.6 MPa. Contact time dependence demonstrated that acetic acid is formed via acetaldehyde formed by a Wacker-type reaction, not through ethanol by hydration of ethylene.     

Studies on crystallization behaviors and crystal morphology of polyamide 66/clay nanocomposites

X‐ray diffraction methods, DSC thermal analysis, and polarized light microscopy (PLM) were used to investigate the structural changes of nylon 66/clay nanocomposites. PA 66/clay nanocomposites were prepared by the method of melt intercalation. The results indicate that the addition of the intercalated organo‐montmorillonite (OMMT) can induce generation of the β‐form crystal of PA 66 and substantially affect the arrangement of molecules in the α‐form crystal, although the crystallinity scarcely changes. Also, the DSC results indicate that the addition of OMMT in the PA 66 matrix leads to increases of crystallization temperatures and the full width at half maximum (FWHM) of the exothermic peaks. Moreover, the viscosity factor is the main influence on FWHM of the exothermic peaks of PA 66/clay nanocomposites. The results of nonisothermal crystallization kinetics show that OMMT has the effect of heterogeneous nucleation and leads to the decrease of the size of the spherocrystal. The heterogeneous nucleation effects of OMMTs influence the mechanism of crystallization and the growth mode of PA 66 crystals. PLM photographs verify that the size of spherocrystal is decreased and visually confirm the theory of crystallization kinetics. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 756–763, 2005     

Preparation of Protein-Stabilized β-Carotene Nanodispersions by Emulsification–Evaporation Method

This work was initiated to prepare protein-stabilized β-carotene nanodispersions using emulsification–evaporation. A pre-mix of the aqueous phase composed of a protein and hexane containing β-carotene was subjected to high-pressure homogenization using a microfluidizer. Hexane in the resulting emulsion was evaporated under reduced pressures, causing crystallization and precipitation of β-carotene inside the droplets and formation of β-carotene nanoparticles. Sodium caseinate (SC) was the most effective emulsifier among selected proteins in preparing the nanodispersion, with a monomodal β-carotene particle-size distribution and a 17-nm mean particle size. The results were confirmed by transmission-electron microscopy analysis. SC-stabilized nanodispersion also had considerably high ζ-potential (−27 mV at pH 7), suggesting that the nanodispersion was stable against particle aggregation. Increasing the SC concentration decreased the mean particle size and improved the polydispersity of the nanodispersions. Nanodispersions prepared with higher β-carotene concentrations and higher organic-phase ratios resulted in larger β-carotene particles. Although increased microfluidization pressure did not decrease particle size, it did improve the polydispersity of the nanodispersions. Repeating the microfluidization process at 140 MPa caused the nanodispersions to become polydisperse, indicating the loss of emulsifying capacity of SC due to protein denaturation.     

XD型醋酸纤维素膜包络体的控制释放特性

用醋酸纤维素膜包络化学肥料、药物、农药等有效成份，研制开发出一类新型的、由内包络体和控速膜构成的控制释放系统──ＸＤ型膜包络体系列。对制备原理、结构形态、膜包络体控制释放特性进行了分析讨论，展示了该类新型控制释放系统的应用前景。     

膨胀型防火涂料的研究

介绍了膨胀型防火涂料的防火机理、组成、特点以及发展趋势。