利用信息融合方法的三维特征提取

本文提出了一种基于信息融合的物体三维特征的提取方法，该方法利用两幅互相配准的三维测距图像和灰度图像，来提取多面体的三维特征。首先，通过分析灰度图像中的灰度变化及测距图像中的测距值变化，分别求取各自图像中物体的特征点及特征边；然后，利用两配准图像之间的对应关系，求得所有特征点、面与多边形在三维测距图像中的三维表示；接着，通过分析三维测距图像中所测得的各候选平面上特定点与边处的曲率及法向，验证候选平面     

Position-sensitive superheated-liquid-droplet neutron dosimeter

The one-dimensional (1D) position-sensitive superheated-liquid-droplet dosimeter (SLDD) has been fabricated and tested in the laboratory. The 1D SLDD is fabricated from a 9.525-mm OD, 6.35-mm ID, 20-cm long, Plexiglas-walled tube filled with a mixture of superheated-liquid Freon droplets and host medium glycerol. Washer-shaped piezoelectric acoustic transducers are positioned at both ends of the tube; they determine the number and positions of the acoustic events when the superheated-liquid droplets evaporate upon neutron irradiation. The SLDD is irradiated with the ¹³⁷Cs and ⁶⁰Co γ-sources, as well as ²⁵²Cf neutron source to test for its radiation response and spatial resolution. The SLDD based on the Freon-134a superheated-liquid droplets operating at 20°C and 1 atm is found to be ideal for measuring absorbed neutron dose. This study also proves that the positions of the radiation-induced nucleation acoustic events can be linearly determined from the differences in the transmission times received by the acoustic transducers on the 1D SLDD. The spatial resolution of the neutron depth-dose is 1 mm due the finite response time (1 μs) of the piezoelectric acoustic transducers.     

Cd-ZSM-5沸石催化剂的制备、表征和芳构化催化性能

采用离子交换、浸渍和混合三种方法制备镉改性ZSM-5沸石催化剂,考察了改性方法和镉含量对催化剂的表面酸性和Cd状态以及芳构化性能的影响。结果表明,加入镉降低了B酸性,Cd~(2+)与沸石结合形成了L_(1612)酸中心,其生成量取决于改性方法和Cd含量,并与芳构化活性提高有直接关系。     

自动交换光网络的标准化现状

国际上许多标准化组织都在对自动交换光网络的相关技术和标准规范进行研究。本文介绍了ITU－T、IETF和OIF等几个主要的标准化组织在自动交换光网络标准方面的进展情况。     

High-frequency small signal AC and noise modeling of MOSFETs for RFIC design

High-frequency (HF) AC and noise modeling of MOSFETs for radio frequency (RF) integrated circuit (IC) design is discussed. A subcircuit RF model incorporating the HF effects of parasitics is presented. This model is compared with the measured data for both y parameter and f_T characteristics. Good model accuracy is achieved against measurements for a 0.25 μm RF CMOS technology. The HF noise predictivity of the model is also examined with measured data. Furthermore, a methodology to extract the channel thermal noise of MOSFETs from HF noise measurements is presented. By using the extracted channel thermal noise, any thermal noise models can be verified directly. Several noise models including the RF model discussed in this paper have been examined, and the results show that the RF model can predict the channel thermal noise better than the other models     

Fabrication of 1.55 μm VCSELs on Si using metallic bonding

Using AuGeNiCr multilayered metals as the wafer bonding medium, long-wavelength GaInAsP/InP vertical cavity surface emitting lasers employing Al-oxide/Si as the upper and lower distributed Bragg reflectors were fabricated on Si substrate with the bonding interface formed outside the vertical cavity surface emitting laser cavity. Laser emission at 1.545 μm was measured under pulsed operations near room temperature. The low-temperature metallic bonding process demonstrates a great potential in device fabrication     

A fully soft-switched extended-period quasi-resonantpower-factor-correction circuit

This paper presents the design criteria, procedure, and implementation of a soft-switched power-factor-correction (PFC) circuit based on the extended-period quasi-resonant (EPQR) principles. All power electronic devices including switches and diodes in the circuit are fully soft switched. The design method is demonstrated in a prototype circuit. The operating principles are confirmed with computer simulation and experimental results. A comparison of the EP-QR operation and zero-voltage-transition (ZVT) pulse-width modulation (PWM) method     

LDD方法在提高电路工作电压中的应用研究

研究了利用轻掺杂漏结构来制作高电源电压器件的工艺方法。分析了ＬＤＤ结构参数对器件击穿特性的影响，并结合实验结果对Ｎ＾－区的注入剂量，长度及引入的串联电阻进行了优化设计。     

NMOS器件两次沟道注入杂质分布和阈电压计算

分别考虑了深浅两次沟道区注入杂质在氧化扩散过程中对表面浓度的贡献。对两次注入杂质的扩散分别提取了扩散系数的氧化增强系数、氧化衰减系数和有效杂地系数，给出了表面浓度与工艺参数之间的模拟关系式，以峰值浓度为强反型条件计算了开启电压，文章还给出了开启电压、氧化条件、不同注入组合之间的关系式。     

地面油管漏失定量测试方法探讨

对油管漏失进行定量测试的方法确定具体漏失位置。方法运用双频道回声探仪探测动液面的原理和工作方法，根据油管漏失形成的死油坏在测试曲线上出现特殊波位置判断油管漏失位置。结果：经过７０多井次的现场试验，该方法具有较高的准确性和可靠性。结论：利用特殊波可以有效监测油管漏失，并具有推广使用价值。