Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Simultaneous degradation of nitroaromatic compounds TNT,RDX, atrazine,and simazine by Pseudomonas putida HK‐6 in bench‐scale bioreactors

BACKGROUND: Environmental contamination by nitroaromatic compounds such as 2,4,6‐trinitrotoluene (TNT), hexahydro‐1,3,5‐trinitro‐1,3,5‐s‐triazine (RDX), atrazine, and/or simazine (TRAS) generated as waste from military and agricultural activities is a serious worldwide problem. Microbiological treatment of these compounds is an attractive method because many explosives and herbicides are biodegradable and the process can be made cost‐effective. We explored the feasibility of using cultures of Pseudomonas putida HK‐6 for simultaneous degradation of TRAS with the aim of microbial application in wastewater treatment in bench‐scale bioreactors. RESULTS: Experiments were conducted to study the effects of supplemental carbons, nitrogens, and Tween‐80 on the degradation of Ps. putida HK‐6 in media containing TRAS as target substrate(s). The most effective TRAS degradation was shown in the presence of molasses. Addition of nitrogen sources produced a delayed effect for the target substrate(s). Tween‐80 enhanced the degradation of target substrate(s). Simultaneous degradation of these compounds proceeded to completion within the given period. CONCLUSIONS: Ps. putida HK‐6 was capable of growth with TRAS, and the effects of supplements on TRAS degradation and simultaneous TRAS degradation were evaluated in bench‐scale bioreactors. The results of this study have practical applications in the processes of industrial waste stream treatment where the disposal of TRAS may be problematic. Copyright © 2008 Society of Chemical Industry     

Interval based MINLP superstructure synthesis of mass exchange networks

A new simultaneous synthesis approach for mass exchange networks (MENs) is presented. The technique is adapted from the interval based mixed integer non-linear program (MINLP) superstructure (IBMS) synthesis of heat exchanger networks (HENs). The superstructure interval boundary compositions are defined by the supply and target compositions of either the rich or lean set of streams. Each rich and lean stream in the superstructure has the potential of exchanging mass with streams of opposite kind in each interval based on mass transfer feasibility. The model harnesses the strengths of the stagewise superstructure and the pinch technology methods for mass exchange network synthesis (MENS). The IBMS approach simultaneously trades-off the capital and operating costs for MENs. The superstructure composition interval defining approach introduced in this paper enforces the mixing of split streams at equal compositions, hence there is no need to include mixing equations in the model. Fixing the interval boundaries helps to eliminate the complexities involved in initialisations, thus the region of search for the optimum solution is reduced. The IBMS model is applied to MENS problems involving continuous contact and staged columns. It is also extended to problems involving multiple mass separating agents (MSAs) and regeneration. The results obtained compare well with those in the literature.     

Determining Frequency and Impulse Response Using Asymmetrical Pulses

A method is presented and analyzed for determining the impulse response and frequency response of a system using an asymmetrical stimulus signal. The considered signal is a pulse with a rapid first transition, followed by a nearly constant region, and then followed by a second transition that is much slower than the first. The advantage of such a signal is that unlike a symmetric pulse, its Fourier transform has no zeros. This allows one to divide by the Fourier transform in the data analysis. It is shown that such a pulse retains the advantages of using an impulse or steplike stimulus. Error estimates similar to those previously published for impulse and steplike stimuli are given for the asymmetric stimulus     

Eigenspannungen als Messgröße zur Qualitätssicherung

Residual stress as measured quantity in quality assurance The x‐ray method is used in the Volkswagen Automotive Group at different world‐wide locations as a standard procedure to determine residual stress. As an important measured quantity in the quality assurance residual stresses are specified in drawings of different components (e.g. gears, coil springs). Measurements are carried out during quality assurance, production, damage analyse, technical development department and design control of components from suppliers. An optimum efficiency can be achieved, if it exists a unique correlation between residual stress values and loading capacity of components, and if the processes to introduce residual stress can be optimized using residual stress measurements during the production.     

Conditionals and conditional probability.

The authors report 3 experiments in which participants were invited to judge the probability of statements of the form if p then q given frequency information about the cases pq, p?q, ?pq, and ?p?q (where ? = not). Three hypotheses were compared: (a) that people equate the probability with that of the material conditional, 1 - P(p?q); (b) that people assign the conditional probability, P(q/p); and (c) that people assign the conjunctive probability P(pq). The experimental evidence allowed rejection of the 1st hypothesis but provided some support for the 2nd and 3rd hypotheses. Individual difference analyses showed that half of the participants used conditional probability and that most of the remaining participants used conjunctive probability as the basis of their judgments. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Iron–cobalt catalysts synthesized by a reverse micelle impregnation method for controlled growth of carbon nanotubes

Fe–Co bimetallic metals supported on CaCO₃ support have been prepared using three different methods for the preparation of the catalysts; wet impregnation (IMP), deposition–precipitation (DP) and reverse micelle impregnation (RM). By careful choice and optimization of CVD reaction conditions and catalyst preparation procedures, we have tailored the nanofabrication of CNTs using 5 wt.% Fe–Co/CaCO₃. High yields of ‘clean’ MWNTs with near 100% selectivity and excellent reproducibility were obtained (1215% and 835% yields for the IMP and DP methods respectively). The RM technique enabled more precise control over the size of the CNTs and a narrower diameter distribution (3–5 nm i.d. and 10–15 nm o.d.) was obtained.     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.