Experimental Investigation of Epoxy Bonded Polymethylmethacrylate Joints

This paper presents an experimental investigation into various aspects of epoxy-bonded polymethylmethacrylate (PMMA) and PMMA-to-aluminium joints. The effects of adhesive thickness, overlap area, surface roughness, and environmental exposure on the joint strength were studied. Results indicated that the joint strength was not directly proportional to the overlap area, while sanding had a positive effect on the joint strength. A negative effect was observed when adhesive thickness was increased. The fatigue behaviour of adhesively-bonded joints under dynamic loading was found to be independent of frequency, for the range of values tested; however, it was dependent on the test temperature with greater reduction in fatigue life observed in PMMA-to-aluminium joints at higher temperature. Empirical equations from which the fatigue life of joints can be predicted were obtained by regression analysis. Intermittent fatigue testing of the joints was also performed. The epoxy adhesive tested proved to be a satisfactory choice for outdoor exposure. The rate of degradation of the adhesive was slow with the adherend itself degrading at a faster rate than the adhesive or the bondline.     

α,β,γ,δ-四-(4-吡啶)卟啉分光光度法测定瓷餐具铜溶出量

本文提出用α，β，γ，δ-四-（4-吡啶）卟啉为显色剂，分光光度法测定瓷餐具铜的溶出量，该方法灵敏度高，选择性好，可以不经分离，直接对试样进行测定，操作简便，结果满意。     

TPR处理剂的研究

利用活性单体苯乙烯与氯丁橡胶、高苯乙烯热塑弹性体接枝聚合，所得产物稀释后用于ＴＰＲ（ＴｈｅｒｍａｌＰｌａｓｔｉｃＲｕｂｂｅｒ）粘接前的预处理，可明显提高剥离强度。     

“八五”期间陶瓷窑用耐火材料的新进展

本文综合评述了“八五”期间我国陶瓷窑用耐火材料工业在合成低膨胀耐火材料，优质高档窑具品种，窑体及窑车隔热耐火等方面的研究与开发进展，以及各类优质耐火材料在建筑卫生陶瓷窑，日用陶瓷窑上的成功应用。     

Potential thread-level-parallelism exploration with superblock reordering

The growing number of processing cores in a single CPU is demanding more parallelism from sequential programs. But in the past decades few work has succeeded in automatically exploiting enough parallelism, which casts a shadow over the many-core architecture and the automatic parallelization research. However, actually few work was tried to understand the nature, or amount, of the potentially available parallelism in programs. In this paper we will analyze at runtime the dynamic data dependencies among superblocks of sequential programs. We designed a meta re-arrange buffer to measure and exploit the available parallelism, with which the superblocks are dynamically analyzed, reordered and dispatched to run in parallel on an ideal many-core processor, while the data dependencies and program correctness are still maintained. In our experiments, we observed that with the superblock reordering, the potential speedup ranged from 1.08 to 89.60. The results showed that the potential parallelism of normal programs was still far from fully exploited by existing technologies. This observation makes the automatic parallelization a promising research direction for many-core architectures.     

Gerontechnology acceptance by elderly Hong Kong Chinese: a senior technology acceptance model (STAM)

The purpose of this study was to develop and test a senior technology acceptance model (STAM) aimed at understanding the acceptance of gerontechnology by older Hong Kong Chinese people. The proposed STAM extended previous technology acceptance models and theories by adding age-related health and ability characteristics of older people. The proposed STAM was empirically tested using a cross-sectional questionnaire survey with a sample of 1012 seniors aged 55 and over in Hong Kong. The result showed that STAM was strongly supported and could explain 68% of the variance in the use of gerontechnology. For older Hong Kong Chinese, individual attributes, which include age, gender, education, gerontechnology self-efficacy and anxiety, and health and ability characteristics, as well as facilitating conditions explicitly and directly affected technology acceptance. These were better predictors of gerontechnology usage behaviour (UB) than the conventionally used attitudinal factors (usefulness and ease of use).

Practitioner Summary: Previous studies have not given much consideration to age-related health and associated abilities when examining acceptance of technology by the ageing population. By encompassing conventional technology acceptance constructs together with age-related health and ability characteristics, the present study was able to identify more factors affecting gerontechnology acceptance by older Hong Kong Chinese.     

Utility of stereoscopic displays for indirect-vision driving and robot teleoperation

The effectiveness of an active shutter-glasses stereoscopic display (SD) and a passive polarised SD was evaluated in a live robot-teleoperation task and a simulated indirect-vision driving task in various terrains. Overall, participants completed their tasks significantly faster with the SDs in three-dimensional (3D) mode than with the SDs in the baseline 2D mode. They also navigated more accurately with the SDs in 3D mode. When the effectiveness of the two types of SDs was examined separately, results showed that the active shutter-glasses SD resulted in faster responses and task completion times than the passive polarised SD, though most of the differences failed to reach statistical significance. Perceived workload when interacting with the two SD systems did not differ significantly between the active versus passive display types or between the 3D and 2D modes of operation; however, participants reported more severe discomfort after interacting with the passive polarised SD.     

Design and realization of a high resolution (640 × 480) SWIR image acquisition system

A new image acquisition system module for extracting signals of high-resolution short wave infrared (SWIR) from a focal plane array (FPA) is presented in this study. The short wave infrared (SWIR—with wavelength about 900–1,700 nm) images have been proven its unique values in many applications such as military, semiconductor inspection and aviation security. The designs for the SWIR data acquisition system module consists of digitization and acquisition of FPA signals, design of synchronous dynamic random access memory controller and real-time image signal transformation and display. Three major steps involved towards a successful SWIR module—(1) Selection of hardware ICs according to specification for the FPA; (2) Design of a timing generator for the image acquisition system to control FPA and other ICs by Verilog HDL programming; (3) Integrate the individual modules on a PCB. The SWIR image output signals are successfully generated in the format of National Television System Committee (NSTC), which can be displayed on a common NTSC monitor, flat panel displays with an AV input terminal or a CRT display in a favorable speed of frame rate at 30 per second.     

Synthesis,characterization, and thermal properties of phosphorus‐containing,wholly aromatic thermotropic copolyesters

A series of phosphorus‐containing, wholly aromatic thermotropic copolyesters from acetylated 2‐(6‐oxide‐6H‐dibenz〈c,e〉〈1,2〉oxa phosphorin‐6‐yl)‐1,4‐dihydroxy phenylene, p‐acetoxybenzoic acid, terephthalic acid, and isophthalic acid were prepared by melting polycondensation. The structure and basic properties of the polymers, such as the glass‐transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity, were investigated with Fourier transform infrared, elemental analysis, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray diffraction, and hot‐stage polarizing optical microscopy. The copolyesters had relatively high T_g values ranging from 183 to 192°C. The T_m values obtained from DSC curves for samples P‐20 and P‐25 were 290 and 287°C, respectively (where the number in the sample name indicates the molar fraction of the phosphorus‐containing monomer in the reactants). The initial flow temperatures of other samples observed with hot‐stage polarizing microscopy were 271–290°C. The 5% degradation temperatures in nitrogen ranged from 431 to 462°C, and the char yields at 640°C were 41–52%. All the copolyesters, except P‐40, were thermotropic and nematic. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1278–1284, 2002     

Muscular fatigue and maximum endurance time assessment for male and female industrial workers

A single arm pushing experiment was conducted in an electronic factory in Yantai, China to assess muscular fatigue using the theoretical models of muscular strength and maximum endurance time (MET) developed by Ma et al. (2009). Seventy seven workers, including 38 males and 39 females, participated in the study. The muscular strength of pushing was measured after the subject pushed a stick, with a force of 2.5 kgf, for 0.5, 1.0, 1.5, 2.0, 2.5, and 3.0 min. Fatigue rate was determined based on a regression approach. In addition to the theoretical model, the MET for such a pushing task was also determined using four empirical models in the literature. The results indicated that females were more resistant to muscular fatigue than males in the pushing task. The results of the muscular strength prediction show that the predictability of the muscular strength model is acceptable. The prediction errors for muscular strength for female subjects were significantly lower than those of the male subjects. The predicted MET using the theoretical model, with a group constant k, was highly correlated with those using the empirical models compared in the current study.