Analysis of Aerosols from the World Trade Center Collapse Site,New York,October 2 to October 30, 2001

The collapse of the World Trade Center (WTC) buildings #2 (South Tower), #1 (North Tower), and #7 created an enormous collapse pile which emitted intense plumes of acrid smoke and dust until roughly mid-December, when the last spontaneous surface fire occurred. We collected particles by size (8 modes, ≈12 to 0.09 micrometers diameter) and time (typical resolution of 1 to 3 h) from October 2 until late December at the EML 201 Varick Street site roughly 1.8 km NNE of the collapse site and 50 m above ground level. Here we show some of the 70,000 mass and elemental data from the time period October 2 through October 30. Identification of a WTC collapse pile source for aerosols seen at the receptor site were based upon the simultaneous presence of finely powdered concrete, gypsum, and glass with intense very fine combustion mode mass episodes concurrent with winds from the southwest quadrant. The results, derived from seven independent beam-based analytical techniques, showed that while PM₁₀ and PM_2.5 24 h values rarely, if ever, violated federal air quality standards, WTC-derived plumes swept over lower Manhattan Island, resulting in intense aerosol impacts of duration a few hours at any one site. The WTC plume resembled in many ways those seen from municipal waste incinerators and high temperatures processes in coal-fired power plants. The size fractions above 1 micrometer contained finely powdered concrete, gypsum, and glass, with sootlike coatings and anthropogenic metals, but little asbestos. Composition in the very fine size range (0.26 > D_p > 0.09 μm) was dominated by sulfuric acid and organic matter, including polycyclic aromatic hydrocarbons (PAHs) and their derivatives, and glasslike silicon-containing aerosols. Many metals were seen in this mode, most, but not all, at low concentrations. The concentrations of very fine silicon, sulfur, and many metals, as well as coarse anthropogenic metals, decreased markedly during October, probably in association with the cooling of the collapse piles. Values of very fine elements seen in May, 2002 at the WTC site were only a few percent of October values.     

Size Distributions of Species in Fine Particles in Denver Using a Microorifice Impactor

Size-fractionated fine particles in Denver, Colorado, were collected by a microorifice impactor and analyzed for mass and elemental composition by a β-gauge and an X-ray fluorescence spectrometer. A least-squares procedure was used to fit a lognormal distribution function to the data in order to determine values and uncertainties for the mass median aerodynamic diameter and geometric standard deviation. The validity of the uncertainties so determined was tested by comparing them to uncertainties derived from Monte Carlo simulations.     

Spectroscopic Analysis of Southern Pine Treated with Chromater Copper Arsenate. I. X-Ray Photoelectron Spectroscopy (XPS)-17

Abstract

The amount of southern pine lumber treated with chromated copper arsenate annually is considerable, yet the association of this preservative with the wood structure is not clear. The current study was undertaken to elucidate the nature of chemical reactions occurring between the components of the treating solution and the constituents of wood. Small, clear Southern pine samples were treated with six different preservative solutions (Cr; Cr/Cu; Cr/As; CCA-A; CCA-B; CCA-C), at 6.4 and 40 Kg/m³ (0.4 and 2.5 pcf) retentions, and compared to water treated and untreated controls. Samples were dried following treatment and analyzed by X-ray photoelectron spectroscopy (XPS). Evaluation of XPS data indicated that the preservative components reacted with wood, through aromatic and possibly alkene substitution, while oxidation of hydroxyl groups was not detected. The proposed wood/CCA bonding also offers an explanation for differences in hardwood and softwood durability following treatment.     

A micromechanically motivated finite element approach to the fracture toughness of silicon nitride

Silicon nitride is often used, when high fracture toughness and strength is needed. For a safe and economic structural design with this material, a prediction of its resistance against thermal and mechanical loads is important. The finite element method together with a continuum damage mechanics model allows for such calculations. The parameters of the suggested model have been adjusted to three-dimensional micromechanical finite element simulations, which include models for the microstructure, the thermoelasticity and the fracture. The material model is used for four-point bend test simulations. The results are compared to recent experiments.