The low process yield of some PNP power transistors

A study is presented of the symptoms of the devices in a slice of PNP power transistors with a poor yield. The failure modes over the slice are analysed. In specific areas the electrical characteristics and optical appearance of the devices were studied and failure statistics are presented. The low yield is ascribed to cracks in the phosphosilicate glass used for the base diffusion. The effect of these cracks is just visible in the optical and scanning electron microscope.     

Deformation of Rodlike Elements of Composite Materials Subjected to Uniform Compression

On the basis of generalization of the results of investigation of the operation of rodlike elements of composite materials, we make a conclusion that the influence of various factors on the deformability of these elements is studied incompletely. The comparison of the stress-strain states for different models of concrete and reinforced-concrete elements makes it possible to describe the effect of longitudinal reinforcement (coefficient of reinforcement, strength and deformation characteristics) on the critical level of strains in the cross section. According to the results of our investigations, we give recommendations concerning the evaluation of the critical value of the coefficient of reinforcement above which one may observe the effect of reinforcement on the deformability of the analyzed sections. It is shown that the compression strength of the brittle base of the composite with inhomogeneous structure decreases as a result of the fracture processes. It is also demonstrated that the existing procedure used for the evaluation of the indicated decrease in strength requires significant improvement. The problem of evaluation of the ultimate value of the coefficient of reinforcement is also analyzed.     

Synthesis, Characterization, and Formation Process of Na-X Zeolite from Coal Fly Ash

Using the SiO₂ and Al₂O₃ components of the amorphous phase in coal fly ash (Fa), Fa was converted to Na-X zeolites in NaOH-NaAlO₂ solutions by stirring at 35°C for 72 hr and then aging at 85°C for a given period. The molar ratio SiO₂/Al₂O₃ of the starting materials was controlled from 2.0 to 13.2. The resulting materials were characterized by various means. Increasing the SiO₂/Al₂O₃ ratio of the starting material increased the degree of crystallinity of faujasite, exhibiting a maximum at SiO₂/Al₂O₃ = 8.0. The faujasite formed was identified as Na-X zeolite with Si/Al = 1.20. The amorphous phase in Fa was dissolved during the stirring to form a precursor of zeolite, such as amorphous aluminosilicate. The Na-X zeolite was formed by aging for 24 hr, and the degree of crystallinity of this material was increased with the increasing aging period. The cation exchange capacity and specific surface area were increased with the increasing degree of crystallinity of the Na-X zeolites.     

Synthesis and Structure of Complexes of Np(V) Perchlorate and Np(V) Chloride with Urea

The crystal structure of [NpO₂{OC(NH₂)₂}₅]ClO₄·H₂O and [NpO₂Cl{OC(NH₂)₂}₄] was studied by X-ray diffraction. The electronic absorption spectra of these complexes were recorded. The coordination polyhedron of Np in both complexes is a distorted pentagonal bipyramid. There is no cation-cation interaction of neptunyl cations in these complexes.     

Numerical simulation of Zn coating solidification

A numerical model, which simulates nucleation and growth of Zn grains, has been developed in order to describe quantitatively the solidification of Zn coatings during the hot-dipping process. The inputs of the model are the nucleation distribution, which has been measured by electron backscattered diffraction (EBSD), and the dendritic growth kinetics, calculated with an analytical model of a parabolic dendrite tip modified to account for the interactions with the coating interfaces. The model predicts the shapes of the grain envelopes as a function of the grain orientation and the texture induced by growth. Three types of grain envelopes have been evidenced, depending on the angle between the c-axis and the normal to the coating plane. Moreover, it has been shown that growth reinforces the already existing {00.1} nucleation texture, in good agreement with experimental data. The model also predicts the cooling curve, including recalescence, and the grain size. Thus, it is used to describe the effects of Pb additions on solidification. In particular, it has been shown that Pb increases the nucleation undercooling and strongly decreases the density of active nuclei, thus resulting in a much larger grain size.     

Microscopic and Macroscopic Growth Rates of Fatigue Cracks in Steels and Alloys under the Influence of Crack Closure

On the basis of the experimental data, we show that the difference between the macroscopic and microscopic fatigue crack growth rates in the second section of the kinetic diagram of fatigue fracture is caused by the effect of crack closure within the limits of its existence. We establish the relationships between the macroscopic and microscopic fatigue crack growth rates and the structure of the material in the second section of the diagram for various values of the load ratio with regard for the effect of crack closure and propose a procedure of examination of the fracture processes in structural materials based on the analysis of microscopic and macroscopic fatigue crack growth rates.     

The Loss of Hydrophobic Polypeptides during Fermentation and Conditioning of High Gravity and Low Gravity Brewed Beer

The object of this study was to investigate the loss of hydrophobic polypeptides, which are important for foam quality and stability in finished beer. Loss of hydrophobic polypeptide due to fermenter foaming occurs during transfer of fermented wort since a gradient of hydrophobic polypeptides towards the surface is created during fermentation. Due to higher polyphenol levels in high gravity (20°Plato) wort, more hydrophobic polypeptides are lost due to cold break (cold trub) precipitation compared to low gravity (12°Plato) wort. Another important factor affecting the loss of hydrophobic polypeptides could be proteinase A activity during fermentation, especially in high gravity fermentation where the yeast is exposed the higher stress. During high gravity fermentation, where osmotic pressures are higher, ethanol levels become greater, and nitrogen‐carbohydrate ratios are lower, more proteinase A is released by the yeast. This release of proteinase A into fermenting wort could have implications for the foam stability of the finished product.     

The effect of mischmetal addition on the structure and mechanical properties of a cast Al-7Si-0.3Mg alloy containing excess iron (up to 0.6 Pct)

The effect of Fe content (0.2 to 0.6 pct) on the microstructure and mechanical properties of a cast Al-7Si-0.3Mg (LM 25/356) alloy has been investigated. Further, 1 pct mischmetal (MM) additions (a mixture of rare-earth (RE) elements) were made to these alloys, and their mechanical properties at room and at elevated temperatures (up to 200 °C) were evaluated. A structure-property correlation on this alloy was attempted using optical microstructure analysis, fractographs, X-ray diffraction, energy-dispersive analysis of X-rays (EDX), and quantitative metallography by image analysis. An increase in Fe content increased the volume percentage of Fe-bearing intermetallic compounds (β and π phases), contributing to the loweryield strength (YS), ultimate tensile strength (UTS), percentage elongation, and higher hardness. An addition of 1 pct MM to the alloys containing 0.2 and 0.6 pct Fe was found to refine the microstructure; modify the eutectic silicon and La, Ce, and Nd present in the MM; form different intermetallic compounds with Al, Si, Fe, and Mg; and improve the mechanical properties of the alloys both at room and elevated temperatures.     

Equal-channel angular extrusion of beryllium

The equal-channel angular extrusion (ECAE) technique has been applied to a powder metallurgy (P/M) source Be alloy. Extrusions have been successfully completed on Ni-canned billets of Be at approximately 425°C. No cracking was observed in the billets, and significant grain refinement was achieved. In this article, microstructural features and dislocation structures are discussed for a singlepass extrusion, including evidence of <c> and <c+a> dislocations. Significant crystallographic texture developed during ECAE, which is discussed in terms of this unique deformation processing technique and the underlying physical processes which sustain the deformation. S.R. AGNEW, formerly with the Oak Ridge National Laboratory, Oak Ridge, TN 37831-6115 This article is based on a presentation made in the symposium entitled “Defect Properties and Mechanical Behavior of HCP Metals and Alloys” at the TMS Annual Meeting, February 11–15, 2001, in New Orleans, Louisiana, under the auspices of the following ASM committees: Materials Science Critical Technology Sector, Structural Materials Division, Electronic, Magnetic & Photonic Materials Division, Chemistry & Physics of Materials Committee, Joint Nuclear Materials Committee, and Titanium Committee.