Power-dependent dispersion in far-off-resonant raman scattering

We investigate the saturation effects of power broadening, Stark shifting, and population transfer on Stokes conversion in stimulated Raman scattering. We do not make the usual rotating wave approximation because the detuning from the next electronic state is assumed to be in the optical regime. Retaining the counter-rotating terms allows an exact determination of the pump and Stokes indexes of refraction. Steady-state solutions for the Stokes intensity and phase are obtained and the effects of making the rotating wave approximation (RWA) are discussed. Finally, we examine the behavior of these solutions for Stokes conversion in hydrogen gas when geometric propagation is appropriate.     

PCR-based procedures in detection and DNA-fingerprinting of Salmonella from samples of animal origin

The usefulness of selected PCR-protocols for the detection of Salmonella in 117 samples of animal origin (17 raw minced meat, 27 raw chicken meat, 8 raw sausages, and 25 egg samples, as well as 18 poultry faecal, and caecal swabs samples) and DNA-fingerprinting typing is shown. To establish an accurate PCR-procedure for Salmonella detection the following parameters were evaluated: two pre-PCR concentration procedures, centrifugation and immunomagnetic separation (IMS) using Dynabeads anti- Salmonella; the specificity and sensitivity of 10 sets of primers; and different conditions of the amplification reaction. In light of the results obtained from the use of PCR-based procedures alone or in combination with conventional methods, the following findings can be underlined: First, IMS is more efficient than centrifugation in the recovery of Salmonella. Second, the selected IMS/PCR-detection protocol is less time-consuming (45 h) than the IMS/culture procedure (90 h), and a good concordance between them was found when the Kappa coefficient was calculated (0·87). Third, PCR-ribotyping technique showed a very low discrimination power, being able to differentiate only three profiles. Fourth, RAPD technique using specific primers supports previous works in which it was proposed as a simple and useful tool for discriminating isolates between and within serotypes. Fifth, The efficiency, rapidity, and flexibility of the PCR-protocols applied were high, and they can be performed using two PCR-programs and the same basic equipment.     

Mechanisms of Active Fuzzy Expertise

Consideration was given to the decision making procedures based on the fuzzy messages of experts whose preferences on the set of collective decisions can also be fuzzy.     

Analysis of a stiffener intersection eccentricity in a steel containment

Containment structures have several regions in which the continuity of the cylindrical pressure boundary is interrupted, e.g., shell penetrations, discontinuous stiffeners, and changes in the shell thickness. Significant strain concentrations can occur in these areas of discontinuity. The Sandia National Laboratories 1:8-scale steel containment equipment hatch was analyzed as an example of an eccentricity at a stiffener intersection.A portion of the as-built 1:8-scale model was modeled with the ANSYS general purpose finite element program using triangular, thin shell finite elements. The overall size of the model was determined from Saint-Venant type considerations of the stress field around the hatch. Shell elements were used to model the ring and formed stiffeners. Geometric and material nonlinear behavior were included. The model was loaded using discrete load steps up to a pressure of 165 psig. At this pressure, the maximum strain was 19.7 percent in the formed stiffener near its intersection with the ring stiffener. The finite element solution demonstrated the very localized nature of the strain field near the ring/formed stiffener intersection.In an attempt to reduce analysis costs, a small portion of the 1:8-scale model immediately surrounding the ring/formed stiffener intersection was selected for further analysis. Two smaller models, a ring/formed stiffener intersection and a ring/circular stiffener intersection, were studied. The models were significantly smaller than the regions used previously. A comparison of the two intersection models showed that the circular stiffener is a more efficient configuration.     

Phase transformations in highly disperse powders during their rapid heating and cooling

Phase transformations in particles of ultrafine powders of graphite, hexagonal boron nitride, and quartz during rapid heating and cooling by passage through a laser beam were investigated. A continuous infrared laser with a wavelength of 10.6 μm was used as a heat source through which the powders were recycled several times. Methods of concentrating the product phases are described. Particles of diamond, carbides, cubic boron nitride, koesite and stishovite were obtained in the mixed products.     

Effects of solvent and temperature on the coupling agent/epoxy resin interface

Increased wetting of the coupling agent/epoxy resin interface was observed when γ-glycidoxypropyltrimethoxysilane, polyfunctional aminosilane and γ-aminopropyltriethoxysilane were applied respectively from methyllethylketone, dimethylformamide and water on woven glass cloths which had been cleaned at 300°C. However, when factory-applied coupling agents were burnt off the woven cloths and fresh coupling agents re-applied, it was found that the nature of the factory-applied coupling agent influenced subsequent wetting. Thinner glass fibres showed a greater improvement in wetting rate than thicker fibres in those solvents identified to be good for improved wettability, irrespective of the heat-cleaning temperature.