Ionic conductivity in oxide heterostructures: the role of interfaces

Rapidly growing attention is being directed to the investigation of ionic conductivity in oxide film heterostructures. The main reason for this interest arises from interfacial phenomena in these heterostructures and their applications. Recent results revealed that heterophase interfaces have faster ionic conduction pathways than the bulk or homophase interfaces. This finding can open attractive opportunities in the field of micro-ionic devices. The influence of the interfaces on the conduction properties of heterostructures is becoming increasingly important with the miniaturization of solid-state devices, which leads to an enhanced interface density at the expense of the bulk. This review aims to describe the main evidence of interfacial phenomena in ion-conducting film heterostructures, highlighting the fundamental and technological relevance and offering guidelines to understanding the interface conduction mechanisms in these structures.     

Nanoporous materials: Porous Graphene as an Atmospheric Nanofilter (Small 20/2010)

The fabrication of nanoscale membranes exhibiting high selectivity is an emerging field of research. The possibility to use bottom‐up approaches to fabricate a filter with porous graphene and analyze its functionality with first principle calculations is investigated. Here, the porous network is produced by self‐assembly of the hexaiodo‐substituted macrocycle cyclohexa‐m‐phenylene (CHP). The resulting porous network exhibits an extremely high selectivity in favor of H₂ and He among other atmospheric gases, such as Ne, O₂, N₂, CO, CO₂, NH₃, and Ar. The presented membrane is superior to traditional filters using polymers or silica and could have great potential for further technological applications such as gas sensors or fuel cells.     

Multi-walled carbon nanotube/nanostructured zirconia composites: Outstanding mechanical properties in a wide range of temperature

Multi-walled carbon nanotube (MWCNT)/nanostructured zirconia composites with a homogenous distribution of different MWCNT quantities (ranging within 0.5-5 wt.%) were developed. By using Spark Plasma Sintering we succeeded in preserving the MWCNTs firmly attached to zirconia grains and in obtaining fully dense materials. Moreover, MWCNTs reduce grain growth and keep a nanosize structure. A significant improvement in room temperature fracture toughness and shear modulus as well as an enhanced creep performance at high temperature is reported for the first time in this type of materials. To support these interesting mechanical properties, high-resolution electron microscopy and mechanical loss measurements have been carried out. Toughening and creep hindering mechanisms are proposed. Moreover, an enhancement of the electrical conductivity up to 10 orders of magnitude is obtained with respect to the pure ceramics.     

Does the extracorporeal blood flow affect survival of the arteriovenous vascular access?

Hemodiafiltration with high‐convective volumes is associated with improved patient survival, whereby practical realization is contingent on high extracorporeal blood flow (Qb) and dialysis treatment time. However, Qb is restricted by vascular access (VA) quality and/or concerns that high Qb could damage the VA. Taking VA quality into consideration, one can investigate the relationship between Qb and VA survival. We analyzed data from 1039 patients treated by hemodiafiltration over a 21‐month period where access blood flow (Qa) measurements were also available at baseline. VA failure was defined as a surgical intervention resulting in the generation of a new VA. Qa was included as a stratification variable within a Cox regression model. A second Cox proportional hazard model with a penalized spline was used to describe the association between Qb and VA survival. Compared with Qb in the 350–357 mL/min range, a significantly higher hazard ratio (HR) for VA failure was detected for fistula only, and then only for Qb < 312 mL/min (HR: 2.361, 95% confidence interval [CI]: 1.251–4.453), Qb = 387–397 mL/min (HR: 1.920, 95% CI: 1.007–3.660) and Qb >414 mL/min (HR: 2.207, 95% CI: 1.101–4.424). Age, gender, diabetes, VA vintage, position of the VA, and arterial pressure were not significantly associated with outcome. The form of the penalized spline confirmed higher risk for VA failure for the lowest and the highest values of Qb. Taking Qa into consideration, no association was found between VA failure and Qb up to flows as high as approximately 390 mL/min.     

Localized auxin peaks in concentration-based transport models of the shoot apical meristem

We study the formation of auxin peaks in a generic class of concentration-based auxin transport models, posed on static plant tissues. Using standard asymptotic analysis, we prove that, on bounded domains, auxin peaks are not formed via a Turing instability in the active transport parameter, but via simple corrections to the homogeneous steady state. When the active transport is small, the geometry of the tissue encodes the peaks’ amplitude and location: peaks arise where cells have fewer neighbours, that is, at the boundary of the domain. We test our theory and perform numerical bifurcation analysis on two models that are known to generate auxin patterns for biologically plausible parameter values. In the same parameter regimes, we find that realistic tissues are capable of generating a multitude of stationary patterns, with a variable number of auxin peaks, that can be selected by different initial conditions or by quasi-static changes in the active transport parameter. The competition between active transport and production rate determines whether peaks remain localized or cover the entire domain. In particular, changes in the auxin production that are fast with respect to the cellular life cycle affect the auxin peak distribution, switching from localized spots to fully patterned states. We relate the occurrence of localized patterns to a snaking bifurcation structure, which is known to arise in a wide variety of nonlinear media, but has not yet been reported in plant models.     

Room-temperature terahertz detectors based on semiconductor nanowire field-effect transistors

The growth of semiconductor nanowires (NWs) has recently opened new paths to silicon integration of device families such as light-emitting diodes, high-efficiency photovoltaics, or high-responsivity photodetectors. It is also offering a wealth of new approaches for the development of a future generation of nanoelectronic devices. Here we demonstrate that semiconductor nanowires can also be used as building blocks for the realization of high-sensitivity terahertz detectors based on a 1D field-effect transistor configuration. In order to take advantage of the low effective mass and high mobilities achievable in III-V compounds, we have used InAs nanowires, grown by vapor-phase epitaxy, and properly doped with selenium to control the charge density and to optimize source-drain and contact resistance. The detection mechanism exploits the nonlinearity of the transfer characteristics: the terahertz radiation field is fed at the gate-source electrodes with wide band antennas, and the rectified signal is then read at the output in the form of a DC drain voltage. Significant responsivity values (>1 V/W) at 0.3 THz have been obtained with noise equivalent powers (NEP) < 2 × 10(-9) W/(Hz)(1/2) at room temperature. The large existing margins for technology improvements, the scalability to higher frequencies, and the possibility of realizing multipixel arrays, make these devices highly competitive as a future solution for terahertz detection.     

3D fiber deposited polymeric scaffolds for external auditory canal wall

The external auditory canal (EAC) is an osseocartilaginous structure extending from the auricle to the eardrum, which can be affected by congenital, inflammatory, and neoplastic diseases, thus reconstructive materials are needed. Current biomaterial-based approaches for the surgical reconstruction of EAC posterior wall still suffer from resorption (biological) and extrusion (synthetic). In this study, 3D fiber deposited scaffolds based on poly(ethylene oxide terephthalate)/poly(butylene terephthalate) were designed and fabricated to replace the EAC wall. Fiber diameter and scaffold porosity were optimized, leading to 200?±?33?µm and 55%?±?5%, respectively. The mechanical properties were evaluated, resulting in a Young’s modulus of 25.1?±?7.0?MPa. Finally, the EAC scaffolds were tested in vitro with osteo-differentiated human mesenchymal stromal cells (hMSCs) with different seeding methods to produce homogeneously colonized replacements of interest for otologic surgery. This study demonstrated the fabrication feasibility of EAC wall scaffolds aimed to match several important requirements for biomaterial application to the ear under the Tissue Engineering paradigm, including shape, porosity, surface area, mechanical properties and favorable in vitro interaction with osteoinduced hMSCs.

Open image in new window

This study demonstrated the fabrication feasibility of outer ear canal wall scaffolds via additive manufacturing. Aimed to match several important requirements for biomaterial application to ear replacements under the Tissue Engineering paradigm, including shape, porosity and pore size, surface area, mechanical properties and favorable in vitro interaction with osteo-differentiated mesenchymal stromal cells.

     

Performance of mortars containing recycled fine aggregate from construction and demolition waste

Waste from construction and demolition accumulates in large quantities in the modern world. Recycled coarse aggregates derived from this waste can replace virgin aggregates used in the production of new concretes but the studies on the effect of using the fine fraction of this waste on the properties of new concrete have not yet led to clear conclusions. The present study evaluated the properties of recycled fine aggregates derived from two recycling plants using two different waste treatment procedures, as well as their effects on the properties of fresh and hardened mortars prepared using these aggregates at two water-to-cement ratios and three replacement ratios. It was found that the recycled aggregates were more porous than the natural aggregates and may have contained some organic matter. Setting times were longer when recycled aggregates replaced natural aggregates and strength and durability were reduced as well. Partial replacement of the fine aggregate is possible if an appropriate compensation of the water to cement ratio is applied.     

Microstructure and properties of epitaxial Sr<Subscript>2</Subscript>FeMoO<Subscript>6</Subscript> films containing SrMoO<Subscript>4</Subscript> precipitates

Thin films of Sr₂FeMoO₆ (SFMO) were grown by pulsed laser deposition in non-optimized argon ambient pressures. The films were found to contain a high number of precipitates of foreign phases. The nature and microstructure of these phases were investigated in detail by high-resolution scanning transmission electron microscopy (STEM) and X-ray diffractometry (XRD). We found out that the dominant foreign phase embedded in the SFMO film matrix was SrMoO₄ (SMO). Through STEM and XRD analysis, we determined that the SMO phase grows epitaxially with respect to the surrounding SFMO matrix and has a fairly good crystallinity. Although the SFMO films include many foreign precipitates, they still exhibit good conducting properties and moderate magnetization values. Tuning the growth of the SMO phase on top of SFMO films to obtain a natural tunnel barrier might pave the way for future applications of SFMO in spintronic devices.     

High accuracy alignment facility for the receiver and transmitter of the BepiColombo Laser Altimeter

The accurate co-alignment of the transmitter to the receiver of the BepiColombo Laser Altimeter is a challenging task for which an original alignment concept had to be developed. We present here the design, construction and testing of a large collimator facility built to fulfill the tight alignment requirements. We describe in detail the solution found to attenuate the high energy of the instrument laser transmitter by an original beam splitting pentaprism group. We list the different steps of the calibration of the alignment facility and estimate the errors made at each of these steps. We finally prove that the current facility is ready for the alignment of the flight instrument. Its angular accuracy is 23 μrad.