Significance of DNA ploidy in the treatment of T1 glottic carcinoma

OBJECTIVE: To assess the role of DNA ploidy as a predictor of radioresistance in T1 glottic carcinoma. DESIGN: Case-control study. Flow cytometric DNA ploidy measurements were performed on formalin-fixed paraffin-embedded tumor specimens from 15 patients with T1 glottic laryngeal carcinomas in whom radiotherapy had failed and from a matched group of 15 patients in whom an identical radiotherapy regimen was curative. Analysis of DNA content was performed blind to outcome of treatment. SETTING: Academic tertiary referral medical center. PARTICIPANTS: Thirty patients with clinically staged T1, N0, M0 glottic carcinoma. INTERVENTION: All patients received radiation to the larynx through opposed lateral ports at a total dose of 64 to 70 Gy. RESULTS: Ten diploid and five aneuploid histograms were found in the resistant group, and six diploid and nine aneuploid histograms were found in the radiosensitive group. This difference was not statistically significant. A trend toward a higher relapse rate after radiotherapy (62.5%) among patients with diploid tumor compared with those with aneuploid tumor (35.7%) was noted. CONCLUSIONS: DNA ploidy did not predict response to radiotherapy in patients with T1 glottic cancer, probably because of the small number of patients. A trend toward lower risk of local recurrence after radiotherapy in aneuploid tumors was noted. A larger prospective study is needed to assess the value of DNA ploidy in the treatment of early laryngeal cancer.     

Improved HF modem using convolutional coding

The paper describes the design of a digitally implemented modem for use over HF (2-30 MHz) radio channels. As a completely digital approach offers the prospect of a number of significant improvements, a new digital multifrequency-shift-keying (MFSK) modem has been developed that employs a novel digital processing procedure termed code-assisted bit synchronisation (CABS). Signal detection is achieved via a set of noncoherent correlators, whilst symbol synchronisation and error correction are performed using a soft-decision Viterbi decoder. Practical tests of modem show that it operates effectively under both additive white Gaussian noise and real HF channel conditions     

Chelated alkoxyalumoxanes and a silica-free binder based on them

Chelated alkoxyalumoxane oligomers have been synthesized through consecutive hydrolysis and alcoholysis of organoaluminum compounds stabilized by compounds capable of keto-enol tautomerism. The chelated alkoxyalumoxanes were used to prepare a silica-free binder for the fabrication of heat-resistant (up to 2050°C), chemically inert corundum ceramic composites. The likely structures of the synthesized preceramic alumoxane oligomers were inferred from physicochemical characterization results (¹H, ¹³C, and ²⁷Al NMR, IR spectroscopy, mass spectrometry, gel-permeation chromatography, thermal analysis, and elemental analysis).     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.