Comparison of IGBT short-circuit failure “ohmic mode”: Epoxy molded package versus silicone gel module for new fail-safe and interruptible power converters

An epoxy molded package is compared with a silicone gel module with IGBTs chips in short-circuit failure modes with respect to critical energy, I²T_melting and explosion energy capabilities. Special importance was attached to “ohmic mode” assessment and ageing of the failed chips. The molded technology yields a very low and stable R_sc (<10 mΩ) as a “residual ohmic value” of the dies in low energy short-circuit failure, which is analysed through a complete reverse. Continuous thermal cycling tests over a medium time duration (>1000 h) also exhibit an acceptable drift of the R_sc property (<20%). The silicone gel module clearly exhibits an unstable R_sc value due to damage of the “free moving” wire-bonding on the chips. The authors show that the paralleled wires connections and the multiple parallel melting pits allow a sort of active redundancy and a possible on-state operation. All these results are used for the design of new and original failsafe converters. These topologies use only one paralleled safety leg that is spontaneously and directly connected in series with the failed devices, through the low R_sc value of the failed chips, without any additional complexity or extra cost.     

Study of the high throughput flexographic process for silicon solar cell metallisation

A commercially available silver paste was modified to match the flexographic process requirements. Rotational and oscillatory rheological tests were carried out to assess the printability and spreading behaviour of the resulting inks. Then, a multifactorial approach was used on a laboratory‐scale printing press to adapt the flexographic process for the front side metallisation of Cz‐Si solar cells, especially for the seed layer deposit of two layer contacts. To quickly identify the significant process parameters, a fractional design of experiment based on a screening approach at two levels was performed. Afterwards, two full factorial designs of experiments were implemented. While the first one allows a better understanding of the effect of the main factors and interactions, the second allows a fine tuning and a confirmation of the first results. Additionally, this methodology allows corroborating the influence of the ink rheological properties on the printing results. Following the process study and optimisation, a seed layer with an average width of 25 µm was printed at a high 0.3 m/s throughput. Additional results suggest that the line width and the throughput can be further improved, which underlines the potential of flexography for photovoltaic applications. Finally, the light‐induced process was used to thicken the seed layer after a standard firing‐through step, leading to an encouraging 17.9% efficiency on Cz‐Si solar cells. Copyright © 2015 John Wiley & Sons, Ltd.     

The Detector System for the Stratospheric Kinetic Inductance Polarimeter (Skip)

The stratospheric kinetic inductance polarimeter is a proposed balloon-borne experiment designed to study the cosmic microwave background, the cosmic infrared background and Galactic dust emission by observing 1,133 deg \(^2\) of sky in the Northern Hemisphere with launches from Kiruna, Sweden. The instrument contains 2,317 single-polarization, horn-coupled, aluminum lumped-element kinetic inductance detectors (Lekids). The Lekids will be maintained at 100 mK with an adiabatic demagnetization refrigerator. The polarimeter operates in two configurations, one sensitive to a spectral band centered on 150 GHz and the other sensitive to 260 and 350 GHz bands. The detector readout system is based on the ROACH-1 board, and the detectors will be biased below 300 MHz. The detector array is fed by an F/2.4 crossed-Dragone telescope with a 500 mm aperture yielding a 15 arcmin FWHM beam at 150 GHz. To minimize detector loading and maximize sensitivity, the entire optical system will be cooled to 1 K. Linearly polarized sky signals will be modulated with a metal-mesh half-wave plate that is mounted at the telescope aperture and rotated by a superconducting magnetic bearing. The observation program consists of at least two, 5-day flights beginning with the 150 GHz observations.     

Tampering with Cell Division by Using Small‐Molecule Inhibitors of CDK–CKS Protein Interactions

Cyclin‐dependent kinases (CDKs) control many cellular processes and are considered important therapeutic targets. Large collections of inhibitors targeting CDK active sites have been discovered, but their use in chemical biology or drug development has been often hampered by their general lack of specificity. An alternative approach to develop more specific inhibitors is targeting protein interactions involving CDKs. CKS proteins interact with some CDKs and play important roles in cell division. We discovered two small‐molecule inhibitors of CDK–CKS interactions. They bind to CDK2, do not inhibit its enzymatic activity, inhibit the proliferation of tumor cell lines, induce an increase in G1 and/or S‐phase cell populations, and cause a decrease in CDK2, cyclin A, and p27^Kip1 levels. These molecules should help decipher the complex contributions of CDK–CKS complexes in the regulation of cell division, and they might present an interesting therapeutic potential.     

Impact of the Dairy Matrix Structure on Milk Protein Digestion Kinetics: Mechanistic Modelling Based on Mini-pig In Vivo Data

Beyond the individual content in nutrients, it is now established that the matrix structure is also to consider when evaluating the nutritional properties and possible health effects of a food material. The objective of this study was to gain knowledge on the effect of the structure of dairy products on the digestion of milk proteins as inferred from a mathematical modelling of mini-pig in vivo data. Six dairy matrices of the same composition but differing by their physicochemical and structural properties were investigated. They were manufactured using technological processes commonly used in the industry (heat treatment, rennet gelation, acid gelation and mixing). The experimental results cover a 7-h postprandial period and consist of plasmatic amino acid concentrations as well as dry matter contents and chromium concentrations (a marker of the liquid phase of the meal) of samples collected at the stomach exit. The model developed not only accounts for the main digestive events but also for phenomena that can occur within the stomach (milk clotting and aggregate syneresis). It provides a good fitting of all the experimental data and allows estimating parameter values that can be explained by considering the properties of the matrices investigated. The model has also been used to estimate quantities that cannot be observed experimentally (stomach volumes, endogenous secretions, gastric emptying half-time, etc.) in order to recover a better picture of all the results and validate the model predictions against the literature. It even appears that our simulations of gastric emptying and aminoacidemia superimpose very well with previously published data obtained using similar matrices and the same mini-pig species. This study shows that the great differences in the kinetics of amino acid absorption that were observed experimentally can be fully understood by considering the behaviour of the dairy matrices within the stomach. It therefore offers interesting perspectives for the integration of food structure parameters, and more particularly for dairy products, in the comprehensive view of the nutritional quality of food products.     

Origin of an intermediate peak in DMTA analysis of multilayer ABS/PC samples

Three layers film shaped by thermocompression of acrylonitrile butadiene styrene copolymer and polycarbonate have been analyzed in dynamic mechanical thermal analysis in tensile mode. They present two peaks as the film is loaded perpendicularly to the layers and three peaks as the film is loaded in parallel to the layers. Numerical computations confirm that the origin of this peak is not related to a mechanical issue such as the transmission of the imposed deformation from one layer to the other. Using this method, it is demonstrated that this third peak can only be obtained assuming a material transition with its own behavior between layers. Tan δ measurements provide a simple and useful experimental tool to understand more about the interfacial zone in polymer blends.     

Acute impairment of rat renal function by l-NAME as measured using dynamic MRI

OBJECTIVE: To assess the feasibility of utilizing dynamic contrast enhanced (DCE)-MRI for depicting the effects of N (G)-nitro-L: -arginine methylester (L: -NAME), a nitric oxide synthase (NOS) inhibitor, on glomerular filtration rate (GFR) in rats. Since Gd-DTPA is mainly cleared through the kidneys, a first-order kinetic model was used to estimate GFR based on a clearance index (k ( cl )) that describes the tracer transport rate from the renal cortex to the outer medulla. MATERIALS AND METHODS: Normotensive Sprague-Dawley rats were infused with either vehicle (0.9% NaCl) or one of three doses of L: -NAME (1, 3 or 10 mg/kg) for 30 min prior to imaging. In a separate set of animals, systolic blood pressure (SBP) was measured for all treatment groups. RESULTS: L: -NAME caused a significant increase in SBP at all doses when compared to pre-dose values and at the two highest doses, post-infusion, when compared to vehicle. Administration of L: -NAME also led to dose-dependent changes in the rate of Gd-DTPA uptake and tracer concentrations reached in selected regions of the kidney. The k ( cl ) measurements indicated a significant impairment of GFR following NOS blockade at the highest dose of L: -NAME. CONCLUSION: DCE-MRI method detected changes in GFR in response to NO inhibition with L: -NAME. This non-invasive technique could be used in longitudinal studies in preclinical and clinical settings offering a rapid assessment of single-kidney function.     

Genome-wide association study for milking speed in French Holstein cows

Using a combination of data from the BovineSNP50 BeadChip SNP array (Illumina, San Diego, CA) and a EuroGenomics (Amsterdam, the Netherlands) custom single nucleotide polymorphism (SNP) chip with SNP pre-selected from whole genome sequence data, we carried out an association study of milking speed in 32,491 French Holstein dairy cows. Milking speed was measured by a score given by the farmer. Phenotypes were yield deviations as obtained from the French evaluation system. They were analyzed with a linear mixed model for association studies. We identified SNP on 22 chromosomes significantly associated with milking speed. As clinical mastitis and somatic cell score have an unfavorable genetic correlation with milking speed, we tested whether the most significant SNP on these 22 chromosomes associated with milking speed were also associated with clinical mastitis or somatic cell score. Nine hundred seventy-one genome-wide significant SNP were associated with milking speed. Of these, 86 were associated with clinical mastitis and 198 with somatic cell score. The most significant association signals for milking speed were observed on chromosomes 7, 8, 10, 14, and 18. The most significant signal was located on chromosome 14 (ZFAT gene). Eleven novel milking speed quantitative trait loci (QTL) were observed on chromosomes 7, 10, 11, 14, 18, 25, and 26. Twelve candidate SNP for milking speed mapped directly within genes. Of these, 10 were QTL lead SNP, which mapped within the genes HMHA1, POLR2E, GNB5, KLHL29, ZFAT, KCNB2, CEACAM18, CCL24, and LHPP. Limited pleiotropy was observed between milking speed QTL and clinical mastitis.