La doping effects on intergrowth Bi2WO6–Bi3TiNbO9 ferroelectrics

La doping effects on intergrowth Bi₂WO₆–Bi₃TiNbO₉ ferroelectric ceramics were studied by X-ray diffraction, electron probe microanalysis and dielectric spectroscopy. It was found that the La³⁺ distribution, ferroelectric phase transition and dielectric relaxation behavior are apparently affected by La doping. With increasing La³⁺ content, the site of dopant ion varies, the grain growth of Bi₅TiNbWO₁₅ is restrained, the Curie temperature is reduced and broadened. Furthermore, two dielectric relaxation loss peaks were observed both in temperature and frequency spectra. The calculated relaxation parameters revealed the oxygen vacancy related to the relaxation process.     

Mechanical properties of iron processed by severe plastic deformation

In the present study, the mechanical properties of Fe processed via severe plastic deformation (equal-channel angular pressing (ECAP)) at room temperature were investigated for the first time. The grain size of annealed Fe, with an initial grain size of about 200 μm, was reduced drastically during ECAP. After eight passes, the grain size reaches 200 to 400 nm, as documented by means of transmission electron microscopy (TEM). The value of microhardness during pressing increases 3 times over that of the starting material after the first pass and increases slightly during subsequent pressing for higher-purity Fe. Examination of the value of microhardness after eight passes as a function of post-ECAP annealing temperature shows a transition from recovery to recrystallization, an observation that resembles the behavior reported for heavily deformed metals and alloys. The tensile and compression behaviors were examined. In tension, a drop in the engineering stress-engineering strain curve beyond maximum load was observed both in the annealed Fe and the ECAP Fe. This drop is related to the neck deformation. The fracture surface, examined by scanning electron microscopy (SEM), shows vein patterns, which is different from the dimples found on the fracture surface of annealed Fe. In compression, an initial strain-hardening region followed by a no-strain-hardening region was observed in the ECAP Fe. The yield strength in tension of the ECAP Fe was observed to be higher than that in compression. The strengthening mechanisms and softening behavior are discussed.     

赋予针织服装个性魅力的女红工艺

将富于变化的女红工艺与单调的针织服装相结合，会使针织服装由平淡变为丰富，由呆板变为活泼。文章论述了在针织服装中运用女红图案、色彩、材料、针法的原理。     

Squeeze-film effects in MEMS devices with perforated plates for small amplitude vibration

Squeeze-film effects of perforated plates for small amplitude vibration are analyzed through modified Reynolds equation (MRE). The analytical analysis reckons in most important influential factors: compressibility of the air, border effects, and the resistance caused by vertical air flow passing through perforated holes. It is found that consideration of air compressibility is necessary for high operating frequency and small ratio of the plate width to the attenuation length. The analytical results presented in this paper agree with ANSYS simulation results better than that under the air incompressibility assumption. The analytical analysis can be used to estimate the squeeze-film effects causing damping and stiffness added to the system. Since the value of Reynolds number involved in this paper is low (< 1), inertial effects are neglected.     

Heat transfer of a row of three butane/air flame jets impinging on a flat plate

Experiments were performed to investigate the heat transfer characteristics of a row of three premixed, laminar, butane/air flame jets impinging on a water-cooled flat plate. The between-jet interference was found to reduce the heat transfer rate in the jet-to-jet interacting zone due to the depressed combustion. The interference became stronger when the jet-to-jet spacing and/or the nozzle-to-plate distance were/was small. The positive pressure existed in the between-jet interacting zone caused the asymmetric flame and heat transfer distribution of the side jet. The meeting point of the spreading wall jets of the central and the side jets did not occur at the midpoint of the neighboring jets, but at a location shifted slightly outwards. The maximum local heat flux and the maximum area-averaged heat flux occurred at a moderate nozzle-to-plate distance of 5d with a moderate jet-to-jet spacing of 5d. The lowest area-averaged heat flux was produced when both the jet-to-jet spacing and the nozzle-to-plate distance were small. Comparing with a single jet under the same experimental conditions, the heat transfer rates in both the stagnation point and the maximum heat transfer point were shown to be enhanced in a row of three-jet-impingement system. The present study provided detailed information on the heat transfer characteristics of a row of three in-line impinging flame jets, which had rarely been reported in previous study.     

在ad hoc网络中一种新的节能路由切换模型

提出了一种基于能量消耗的路由切换模型(ERHM),它在路由维护中利用切换技术来使路由的能量消耗最小.仿真结果表明采用切换技术的ERHM模型的能量节省量要比不采用切换技术节约1.5～7.5倍,且节点的移动性越大,能量节约越多.     

Chemical compositions and optical properties of HfOxNy thin films at different substrate temperatures

High-k HfO_xN_y thin films have been grown by radio frequency (rf) reactive sputtering of metal Hf target in N₂/Ar/O₂ ambient at different substrate temperatures. The chemical compositions of the films have been investigated as a function of substrate temperature by X-ray photoelectron spectroscopy (XPS). XPS measurements showed that nitrogen concentration increases with an increase in substrate temperature. Room-temperature spectroscopic ellipsometry (SE) with photon energy 0.75–6.5 eV was used to investigate the optical properties of the films. SE results demonstrated that refractive index n increases with an increase in substrate temperature. Based on TL parameters which were obtained from the best fit results used in a simulation of the measured spectra, meanwhile, we conclude that the energy band gap (E_g) decreases with an increase in substrate temperature.     

Intermittent Phenomena in Switched Systems With High Coupling Strengths

In this paper, one kind of intermittency generated by a discontinuous system is studied. Although this system, which is composed of two switched subsystems coupled with a high strength, is nonsmooth, the mechanism of this kind of intermittency can be analyzed with several explicit relations between the intermittency characteristics and the system control parameters. In particular, estimates of "steady-state" values of the system (in the laminar phases) and a critical value for this intermittency can be derived, which are helpful in relevant control systems design. Moreover, some power laws for the observed intermittency are obtained and discussed