All-optical photonic switches using integrated inverted asymmetricFabry-Perot modulators and heterojunction phototransistors

InGaAs/GaAs(100) multiple-quantum-well-based inverted cavity asymmetric Fabry-Perot modulators are vertically integrated with GaAs/AlGaAs heterojunction phototransistors to yield all-optical photonic switches. The photonic switches using `normally on' modulator pixels exhibit an output on-off ratio of 12:1 with internal optical gain of 4 dB. The photonic switches using `normally off' modulator pixels yield similar contrast and gain, but exhibit intrinsic bistable behavior. The inverted cavity modulators employed permit utilizing the transparency of the GaAs substrate at the operating wavelength and offer advantages for fabricating large arrays for optical signal processing     

The use of doped polyaniline as an electrode in the galvanic anodic protection of ferrous metals in industrial acid solutions

In order to investigate the galvanic anodic protection (GAP) of ferrous metals (such as 410, 304 and 316 stainless steels) in acid solutions by doped polyaniline (PANi), separate doped PANi powder-pressed electrodes with different surface areas (the area ratio of the PANi electrode to stainless steel is between 1:1 and 1:2) have been prepared. These were coupled with ferrous metal in the following solutions: 5 M sulphuric acid, 5 M phosphoric acid and industrial phosphoric acid (containing 5 M phosphoric acid and 0.05% chloride ion) to construct a galvanic cell, in which PANi is cathode while ferrous metal is anode. The results indicate that a PANi electrode with sufficient area can provide corrosion protection to stainless steel in these acidic solutions. A pilot scale coupling experiment was carried out. The results indicate that PANi is a promising material as an electrode for the anodic protection of ferrous metals in acidic solutions in industrial situations.     

一氧化碳对聚丙烯收率、结构的影响

分析研究了Montell(Himont)聚丙烯工艺中CO对聚丙烯收率、产品结构的影响。     

α厚层测量法的定标方法探讨

本文比较了几种常用的α厚层测量法的定标方法。实验结果表明,共沉淀法是一种比较理想的定标方法,它所制得的标准样品的定标曲线线性较好,探测效率较稳定。     

北京谱仪端盖簇射计数器工作气体的研究

为使北京谱仪端盖族射计数器更好地工作在自猝灭流光ＳＱＳ模式下，提高其能量分辨以及线性等指标，用Ａｒ，ＣＯ２，Ｌｓｏｂｕｔａｎｅ三元工作气体对探测器的工作性能进行了仔细研究，找出了一适合于主雇地数器的工作气体，此外，还研究了异丁的纯度对探测器性能的影响。     

Suppression of boron penetration in p+ polysilicon gateP-MOSFETs using low-temperature gate-oxide N2O anneal

It has been reported that high-temperature (~1100°C) N₂ O-annealed oxide can block boron penetration from poly-Si gates to the silicon substrate. However, this high-temperature step may be inappropriate for the low thermal budgets required of deep-submicron ULSI MOSFETs. Low-temperature (900~950°C) N₂O-annealed gate oxide is also a good barrier to boron penetration. For the first time, the change in channel doping profile due to compensation of arsenic and boron ionized impurities was resolved using MOS C-V measurement techniques. It was found that the higher the nitrogen concentration incorporated at Si/SiO₂ interface, the more effective is the suppression of boron penetration. The experimental results also suggest that, for 60~110 Å gate oxides, a certain amount of nitrogen (~2.2%) incorporated near the Si/SiO₂ interface is essential to effectively prevent boron diffusing into the underlying silicon substrate     

改性玻纤增强尼龙610,1010塑料

研究了采用(准)中粘度级尼龙做基体树脂,加入成核剂改善尼龙的结晶过程,提高结晶速率和初始熔融温度;添加光、热氧稳定剂,防止尼龙在成型加工和使用过程中产生降解与老化,提高塑料制品的质量和减少性能的分散性;采用合理的工艺条件,确保添加剂的均匀分散与减少玻纤的磨损,得到适于军工、航空和机电等领域需要的高性能的受力结构工程塑料。     

秦山核电厂蒸汽发生器水位控制试验

简要介绍了蒸汽发生器水位控制系统的运行方式和试验方法。试验项目包括旁通阀控制试验、主给水阀控制试验和旁通阀与主给水阀的切换试验。文中给出了试验结果,即在液位扰动和核动率扰动时,蒸汽发生器液位的变化过程。经过两个月的运行和瞬态试验,证明蒸汽发生器水位控制系统满足设计要求。     

Flammability and thermal stability studies of ABS/Montmorillonite nanocomposite

Acrylonitrile–butadiene–styrene (ABS)/montmorillonite nanocomposites have been prepared using a direct melt intercalation technique by blending ABS and organophilic clay of two different particle sizes: OMTa (5 µm) and OMTb (38 µm). Their structure and flammability properties were characterized by X‐ray diffraction, high resolution electronic microscopy (HREM), thermogravimetric analysis (TGA) and cone calorimeter experiments. The results of HREM showed that ABS/5 wt% OMTa nanocomposite was a kind of intercalated–delaminated structure, while ABS/5 wt% OMTb nanocomposite was mainly an intercalated structure. The nanocomposites showed a lower heat release rate peak and higher thermal stability than the original ABS by TGA and cone calorimeter experiments. Also, the intercalated nanocomposite was more effective than an exfoliated–intercalated nanocomposite in fire retardancy. Copyright © 2003 Society of Chemical Industry