在Fe-Al-C系统中合成优质Ⅱa型宝石级金刚石单晶

和优质Ib型宝石级金刚石单晶生长相比，作为当今高温高压晶体生长的一种高精尖技术，优质1／a型宝石级金刚石单晶对合成技术提出了更高更苛刻的要求：枢研究从晶体的生长速度出发，发现一开始阶段（大约几个小时）的晶体生长速度对优质宝石级金刚石单晶的后期生长争关重要。埘Fe-Al-C系统（Al含量不大于2．5wt％）来说，采用多品种法将晶体开始阶段的晶体生长速度由1．5mg／h降至0．5mg／h后，对生长过程中金属包裹体的进入有了明显的抑制作用，晶体的质量有了很大提高。从晶体中包裹体的存任形式来看，为了获得优质Ⅱa型宝石级金刚石单晶，在触媒中人为地添加除氮剂给晶体生长过程中的排杂过程带来了很大的难度：为了更好的实现排杂，必须很好的处理晶体表面的径向平铺生长速度和晶体轴向的堆积生长速度之间的火系。     

LD7铝合金时效工艺的研究

通过试验系统地研究了ＬＤ７铝合金的单级和两级时效工艺。结果表明，与传统的单级时效相比，两级时效在不降低室温强度，硬度的前提下，可显著提高合金的电导率及高温性能。     

稳定态二氧化氯杀菌剂的制备及应用

稳定态二氧化氯(C1O2)是一新型杀菌消毒剂，具有高效、广谱、安全的特性，适用范围广，不产生对人体有害物质。介绍了稳定态ClO2的性质、检测、制备条件及其在有关领域的应用。     

扩链剂在PVC树脂生产中的应用

讨论了常见扩链剂的功能及在聚氯乙烯树脂生产中的应用。     

用瞬时法测定液体导热系数

以珠状热敏电阻为加热元件,建立了用瞬时法测定液体导热系数的装置,在25℃下用乙二醇等7个标准样品,对该装置进行了标定,平均偏差为2%.为了核实装置和所得关系式的可靠性,又测定了13个已知导热系数的样品,多数偏差在2%以内,最大偏差为5%.单次测量的精度为0.2%.本文叙述了这一方法的原理,并对实验结果进行了讨论.     

Rheological properties of mixtures of molten polymer and fluorocarbon blowing agent. I. Mixtures of low-density polyethylene and fluorocarbon blowing agent

The viscosities of mixtures of low-density polyethylene and fluorocarbon blowing agent were determined from the measurement of wall normal stress along the longitudinal axis of a capillary die. For the study, three different grades of commercial high-pressure low-density polyethylene were used, together with the following fluorocarbon blowing agents, dichlorodifluoromethane (FC-12), dichlorotetrafluoroethane (FC-114), and blends of FC-12 and FC-114. In the experiment, blowing agent concentration and melt temperature were varied for each combination of polymer and blowing agent employed. Analysis of the experimental data has led to a correlation between the viscosity reduction factor (VRF) and the blowing agent concentration, in which VRF is defined as the ratio of the viscosity of polymer-blowing agent mixture to that of the polymer alone. It was found that the correlation obtained is independent of shear rate and temperature and dependent upon only the type of fluorocarbon blowing agent. The practical significance of the correlation is discussed. We have shown that the entrance pressure drop obtained in the absence of phase separation in the entrance region may be used as a measure of the elastic properties of mixtures of fluorocarbon blowing agent and low-density polyethylene resin.     

浅析呼和浩特市大气SO2发展趋势及防治对策

本文通过对二氧化硫的形成及危害的阐述，以及对我市近几年大气中二氧化硫监测结果的分析，针对发展趋势和存在的问题，根据实际情况提出相应的建议。     

Morphologies and microstructures of tree-like carbon produced at different reaction conditions in a CVD process

Centimeter-size multi-branched tree-like carbon structures have been generated by the catalytic chemical vapor deposition of toluene using ferrocene as the catalyst precursor and investigated by means of SEM, TEM, and EDX. It is found that a temperature of 1000-1200 °C and a carrier gas flow rate of 1000-2500 ml/min are necessary for the generation of the carbon trees. Their morphologies and microstructures change greatly with the changing reaction conditions. The fractal dimensions of the trees are calculated to quantitatively investigate the influence of different reaction temperatures on the morphologies.