变频器在龙门铣床上的应用

介绍龙门铣床的直流调速控制系统的改造方案，根据龙门铣床工作台运动过程及原直流电机的容量来选择交流电机和变频器并对变频器的功能进行设定。     

Miniaturized Hexagonal Stepped-Impedance Resonators and Their Applications to Filters

Miniaturized hexagonal stepped-impedance resonators and their applications to bandpass filters are presented. Based on the odd- and even-mode equivalent circuits, the resonance characteristics of these resonators are investigated. A series of circuit configurations, including the third-order Chebyshev, trisection, and fifth-order cascaded trisection filters, are constructed by the proposed resonators. These filters are very compact and have good stopband responses. Measured results validate the analysis and theoretical prediction with good agreement.     

基础锚栓预埋加固方案

结合工程实例 ,介绍轻钢结构系统基础锚栓预埋、加固解决方案 ,并介绍了加固系统的制作及使用方法 ,可供工程人员参考     

超低碳奥氏体不锈钢00Cr18Ni10还原脱磷研究

在 2 5kg真空感应炉上用镁钙合金对超低碳奥氏体不锈钢 0 0Cr18Ni10进行了还原脱磷试验。通过充入工业纯氩使炉内压力为 6 6 .6 6kPa和精炼时的反应温度 14 5 0～ 15 0 0℃ ,加入镁钙合金 5 0kg t和助熔剂CaF2 11kg t,可使精炼后 0 0Cr18Ni10的磷含量进一步降低到 (5 0～ 6 0 )× 10 - 6 ,钢中氧、硫含量分别稳定降到(4～ 6 )× 10 - 6 和 15× 10 - 6 。     

Application of ultrasonic waves in activation of microcrystalline cellulose

In this work, microcrystalline cellulose (MCC) was activated with ultrasonic waves. The influences of ultrasonic treatment on the changes of supramolecular structures and morphology structure were studied by WAXS and SEM. The accessibility of the MCC was characterized by water retention value (WRV) and specific surficial area. The influence of ultrasonic treatment on the reactivity of MCC was investigated through the reaction of MCC being oxidized into 2,3‐diadehyde cellulose (DAC) by periodate sodium. The mechanism of the reactivity change of ultrasonically treated MCC was examined. The results showed that the degree of crystallinity of MCC decreased and the degree of polymerization showed little change after treatment with ultrasonic waves. The morphologial variation of the treated MCC was significant when compared with the untreated MCC, which contribute to the improvement of accessibility. The aldehyde content of DAC prepared from ultrasonically treated MCC was improved from 64.19 to 85.00%, indicating that the regioselective oxidation reactivity of MCC was significantly improved. The aldehyde content was found to first increase with time of ultrasonic treatment to a point, and then decrease as time progressed. In addition, the aldehyde content was found to increase with an increase in ultrasonic power. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

A disposable sensor based on immobilization of acetylcholinesterase to multiwall carbon nanotube modified screen-printed electrode for determination of carbaryl

A simple method has been devised for immobilization of acetylcholinesterase (AChE) covalent bonding to a multiwall carbon nanotube (MWNT)-cross-linked cellulose acetate composite on a screen-printed carbon electrode (SPCE) and a sensitive and disposable amperometric sensor for rapid determination of carbaryl pesticide is proposed. The immobilized enzyme was preserved on this film because of the excellent biocompatibility and non-toxicity of cellulose acetate. Based on the inherent conductive properties of the MWNT, the immobilized AChE had greater affinity for ATCl and excellent catalytic effect in the hydrolysis of ATCl. MWNT improved the interface enzymatic hydrolysis reaction and increased the amperometric response of the sensor. Under optimum conditions, the inhibition of carbaryl on AChE increased linearly with the increasing concentration of carbaryl in two ranges, from 0.01 to 0.5 μg mL⁻¹ and from 2 to 20 μg mL⁻¹, with the correlation coefficients of 0.9985 and 0.9977, respectively. The detection limit was 0.004 μg mL⁻¹ taken as the concentration equivalent to 10% decrease in signal. The sensor showed acceptable stability, accuracy and could be fabricated in batches, thus it is economic and portable. This type of disposable enzyme-based amperometric sensor has extensive application potential in environmental monitoring of pesticides.     

Epoxidation of high trans‐1,4‐polyisoprene and its properties

A new organic‐solvent‐free water‐phase suspension method was used to synthesize partially epoxidized high trans‐1,4‐polyisoprene (TPI) to improve its properties, including oil resistance and wet‐skid resistance. The epoxidation was conducted in an aqueous peracetic acid solution and on the TPI granules prepared by a bulk precipitation method with supported titanium catalyst. The effects of the synthesis conditions, including reaction temperature, reaction time, and pH value, on the epoxy content were investigated. Epoxidized trans‐1,4‐polyisoprene (ETPI) with epoxy contents between 10 and 80% were obtained within 4 h. Both the amorphous and crystalline regions of TPI were epoxidized. The crystallization properties decreased with increasing epoxy content. ETPIs possessed lower mechanical properties than TPI but could be enhanced by vulcanization. The oil resistance and wet‐skid resistance were significantly improved after epoxidation. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

A-6A甲胺合成催化剂使用总结

安阳九天化工集团甲胺/DMF(二甲基甲酰胺)工程是河南省重点建设项目.装置采用先进的甲醇和液氨气相催化胺化法生产混甲胺.一期工程30 kt/a 甲胺/DMF装置于2003年10月建成投产,其合成催化剂选用的是上海石化研究院生产的A-6A甲胺合成催化剂,从投产到现在,合成催化剂共更换了4次,催化剂平均使用寿命为13个月,共生产混甲胺112 kt,达到国内领先水平.     

PBT冲击断口弧形形貌研究

分析了不同温度下聚对苯二甲酸丁二醇酯(PBT)的断口形貌,总结了PBT断口弧形条纹的形貌特征,定量研究了弧形条纹数量、特征区尺寸及表面粗糙度的变化规律,并对其形成机理进行了探讨。结果表明:PBT断口弧形条纹可分为脆性弧形条纹和韧性弧形条纹;随温度的升高,PBT断口弧形条纹的数量越来越少,弧形条纹间的平均距离越来越大,弧形形貌的平均粗糙度逐渐减小。     

三代微光管均匀性测试与分析

利用自行研制的“光电阴极多信息量测试系统”首次对国产三代微光管中的GaAs光电阴极的均匀性进行了光谱响应测试 ,结果表明该国产三代微光管存在明显的非均匀性。利用曲线拟合方法估算了GaAs光电阴极的材料性能参数 ,发现表面逸出概率不一致是非均匀性的主要原因 ,GaAs材料的少子扩散长度 (1 1 2～ 1 82 ) μm ,与阴极厚度相当 ,后界面复合速率在 (1× 1 0 5～ 1× 1 0 6 )cm/s之间 ,它限制了阴极灵敏度的提高