Interaction of a ductile projectile with a brittle solid medium

The process of interaction of a ductile projectile with a many times harder brittle target is analyzed in the 500–1000 m/sec range of velocities. The effect of hardness of the target and its fragmentation on the penetration depth is shown.Translated from Problemy Prochnosti, No. 9, pp. 60–62, September, 1991.     

Fabrication of a poly-Si thin-film transistor with storage capacitor

The fabrication process of a low-temperature poly-Si thin-film transistor (TFT) with a storage capacitor was studied. The atmospheric-pressure chemical-vapour deposited SiO₂ protected the buried indium tin oxide (ITO) from reduction by a pure H₂ plasma treatment that was essential for the effective improvement of the poly-Si TFT characteristics. Thus, a storage capacitor with an ITO (picture electrode)-SiO₂-ITO (buried common electrode) structure was successfully fabricated. The poly-Si TFT with a channel width/length W/L ratio of 5 drove a 3 pF storage capacitor in 2 μs, and it showed superior driverability for LCD use. The TFT also had good hold characteristics under illumination for the realization of grey-scale representation.     

Analytical pyrolysis as a tool for the study of plastic coals

The technique of analytical pyrolysis has been used to characterize 40 similar mid-rank western Kentucky coals of widely differing ASTM Gieseler plasticity. Certain pyrolysis/g.c. variables were shown to correlate well with both ASTM Gieseler and isothermal plasticity. Highly plastic coals were shown to exhibit certain characteristic peaks in the 450 °C pyrogram which were absent in the pyrogram of the non-plastic coals. Two coals, representing the two extremes in plasticity, were selected for further study. After extraction with solvents such as DMF the characteristic peaks were absent in the 450 °C pyrogram of the extraction residue of the highly plastic coal. These peaks were also shown to decrease with increasing severity of air oxidation of the plastic coal. This technique appears to be a useful tool for the analysis of mid-rank plastic coals and supports the view that the substances contained in the bitumen fraction of these coals are involved in the development of the plastic state.     

Improved Matrix-Filler Adhesion

Enhanced matrix-filler adhesion is realized after filler treatment with a surface treatment process. The hydrosol/coupling agent treatment was applied to a wide range of inorganic and organic fillers, and adhesion to a variety of matrix resins was improved. Scanning Electron Microscopy (SEM) was used to determine the locus of failure in the filled systems. The locus of failure shows the relative degree of adhesion between the filler and the polymer matrix. Significant improvement in adhesion in humid environments is also observed.     

Pyrolysis and combustion of cellulose. VIII. Thermally initiated reactions of phosphonomethyl amide flame retardants

Several N-(phosphonomethyl) amides have previously been reported to act as particularly effective flame retardants for cellulose. It has also been demonstrated previously that the efficiency of a flame retardant on cellulose frequently parallels its ability to phosphorylate cellulosic hydroxyls at elevated temperatures. This study of the hydrolysis and alcoholysis reactions of N-(phosphonomethyl) amides establishes their unique reactivity. An explanation for this high reactivity is proposed on the basis of intramolecular assistance of the attack of water or alcohols at phosphorus by the carbonyl oxygen of the amide moiety.     

Synthesis of Si3N4 with Emphasis on Si-S-N Chemistry

Industrial production of Si₃N₄ from SiCI₄, is increasing. An element rivaling CI in abundance and cheapness with potentially suitable chemistry for this application is sulfur. Thus, Si–S–N chemistry was investigated to determine its usefulness in producing Si₃N₄. Bifunctionality in S, as opposed to mono-functionality in CI, may allow special routes via polymers to become important.     

Segregation of Isovalent Impurity Cations at the Surfaces of MgO and CaO

Enthalpies of segregation for isovalent impurities in magnesium and calcium oxide as a function of surface concentration were calculated by using an atomistic computer simulation method. We have considered Be²⁺, Mg²⁺, Ca²⁺, Ba²⁺, and Ni²⁺, segregating to both (001) and (110) faces. The results obtained can be extrapolated to predict the behavior of other impurities including Mn²⁺, Fe²⁺, and Co²⁺, We find, for example, that Fe²⁺, Mn²⁺, Ca²⁺, Sr²⁺, and Ba²⁺ will concentrate at the (001) surface of MgO, while Ni²⁺ will be depleted. The enthalpy of segregation is found to vary substantially with coverage particularly for the larger impurities. The enthalpy becomes less negative with increasing impurity concentration due to the increasing lattice strain until the surface is nearly saturated. Then additional stabilization is obtained by restructuring of the surface layer. We predict reconstructed surfaces for both the (001) and (110) faces, which contain a high concentration of a larger impurity ion. The enthalpy of segregation shows a maximum at around 50% surface coverage implying a bimodal surface distribution of segregant. The influence of segregation on surface energy suggests two unusual effects. The (001) surface energy of the impure crystal becomes negative for surface concentrations of impurity greater than 10% Ba²⁺ or 75% Sr²⁺ in MgO. This implies a thermodynamic barrier to sintering. At high coverages of Ba²⁺ in MgO the (110) surface becomes more stable than the (001) face suggesting that facetting may occur.     

Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Stability studies on methyl and ethyl fatty acid esters of sunflowerseed oil

Fatty acid esters, high in linoleic acid, were prepared and stored for long-term engine tests. Storage tests with these esters were undertaken to obtain more information on optimal storage requirements and general stability characteristics. Samples were kept at three temperature levels (20 C, 30 C and fluctuating around 50 C) for a 90-day period and were removed at regular intervals for chemical and physical analysis. The influence of air, temperature, light, TBHQ and contact with mild steel was evaluated by comparing the free fatty acid, peroxide, anisidine, ultraviolet absorption, viscosity and induction periods. A statistical model was used to evaluate the data and to reduce the large number of data points to comparable curves. Storage of esters in contact with air, especially at a temperature above 30 C, resulted in significant increases in peroxide, ultraviolet absorption, free fatty acid, viscosity and anisidine values. Exclusion of air retarded oxidation at all temperature levels. A direct relationship between viscosity increases and oxidation parameters was evident. Exposure to light caused a small increase in the oxidation parameters of esters stored at the highest temperature level. Addition of TBHQ prevented oxidation of samples stored under moderate conditions. Under unfavorable storage conditions the anti-oxidant was no longer effective. Mild steel had very little effect on the oxidation parameters. Only the anisidine values of samples stored at the highest temperature level were slightly increased. Methyl esters performed slightly better than ethyl esters during the storage test. The following practical guidelines for storage of fatty acid ester fuels are: (i) airtight containers should be used; (ii) the storage temperature should be <30 C; (iii) mild steel (rust free) containers may be used, and (iv) TBHQ has a beneficial effect on oxidation stability.