Identification of the adverse effect of nitrate on the phosphate release rate and improvement of EBPR process models.

The adverse effect of nitrate on the phosphate release rate in the anaerobic phase was observed and was hardly explainable with conventional EBPR process models. Four possible mechanisms were proposed including substrate competition, reduced fermentation, parallel reaction and sequential reaction. Batch experiments were designed and conducted to identify the dominant mechanism. Results showed that the sequential reaction was the only possible mechanism where only denitrification occurred if any nitrate existed in the anaerobic phase. Then the phosphate release following after the nitrate was completely removed. Nitrate inhibition effect was added into the PHA storage rate to incorporate the sequential reaction in the conventional ASM3 plus EAWAG bio-P module (ASM3 + P). Nitrate inhibition coefficient, K(I,NO,PAO) was found to be as low as 0.05 mg/L. This correlated well with experimental observation where no also meant that the anaerobic compartment of a continuous flow reactor could be seriously affected by the residual nitrate contained in the sludge recycle flow. This phenomenon caused overestimation of the phosphate uptake rate and consequently underestimation of PO4(3-) -P concentration. This problem was resolved by incorporation of a nitrate inhibition term in the ASM3 + P for more accurate simulation of the EBPR process.     

WWTP dynamic disturbance modelling--an essential module for long-term benchmarking development.

Intensive use of the benchmark simulation model No. 1 (BSM1), a protocol for objective comparison of the effectiveness of control strategies in biological nitrogen removal activated sludge plants, has also revealed a number of limitations. Preliminary definitions of the long-term benchmark simulation model No. 1 (BSM1_LT) and the benchmark simulation model No. 2 (BSM2) have been made to extend BSM1 for evaluation of process monitoring methods and plant-wide control strategies, respectively. Influent-related disturbances for BSM1_LT/BSM2 are to be generated with a model, and this paper provides a general overview of the modelling methods used. Typical influent dynamic phenomena generated with the BSM1_LT/BSM2 influent disturbance model, including diurnal, weekend, seasonal and holiday effects, as well as rainfall, are illustrated with simulation results. As a result of the work described in this paper, a proposed influent model/file has been released to the benchmark developers for evaluation purposes. Pending this evaluation, a final BSM1_LT/BSM2 influent disturbance model definition is foreseen. Preliminary simulations with dynamic influent data generated by the influent disturbance model indicate that default BSM1 activated sludge plant control strategies will need extensions for BSM1_LT/BSM2 to efficiently handle 1 year of influent dynamics.     

Inhibition of microbial growth in ready‐to‐eat food stored at ambient temperature by modified atmosphere packaging

This study was undertaken to develop a modified atmosphere package to control microbial growth in ready‐to‐eat (RTE) products stored at ambient temperature. Ethanol and/or limonene associated with modified atmosphere (CO₂ : O₂ : N₂ = 30% : 5% : 65%) was used to inhibit the growth of total air‐borne microorganisms and Escherichia coli in RTE products stored at 25°C. The results indicated that 0.05% ethanol vapour in the headspace was effective to inhibit the growth of air‐borne microorganisms and E. coli at 25°C for 72 h in a model study, and the effectiveness was related to ethanol content. Both 73 ppm limonene and 0.05% ethanol vapour enhanced the bacteriostatic effect of modified atmosphere in RTE sushi roll products, and no off‐flavour was detected using this formulated gas; however, no significant inhibitory effect was observed for RTE cold noodle products. This study concludes that combinations of carbon dioxide, ethanol or limonene vapours are effective to inhibit microbial growth in RTE food at ambient temperature, and the outcome may be due to the hurdle effect. Copyright © 2003 John Wiley & Sons, Ltd.     

Managing Fashion Goods Inventories: Dynamic Recourse for Retailers with Outlet Stores

The proliferation of both online and bricks and mortar outlet stores underscores the observation that secondary markets are readily accessible to retailers of short-life-cycle products. These secondary markets provide recourse channels for retailers to sell excess inventory of out-of-favor items at reduced prices when overstocking occurs in a primary market. We study the problem of determining when a retailer should terminate its primary selling season by selling remaining inventory on a secondary market. The retailer has a single opportunity to procure prior to a primary selling season consisting of multiple periods. Demand in each period is random, but correlated. At the end of each period, any remaining inventory incurs a holding cost. Then, based upon the current level of inventory and the cumulative demand-to-date, the retailer decides either to terminate the primary selling season by selling all or part of the remaining inventory on a secondary market, or to extend the current primary selling season by another period. We develop structural properties of the optimal policy for determining when to terminate the primary selling season, and we develop corresponding implications for procurement.     

Verhalten von Magnesiumlegierungen für Anwendungen im Fahrzeugbau bei mechanisch‐elektrochemischer Komplexbeanspruchung: Einfluss passivierender Deckschichten und Mechanismen der lokalen Schädigung

Behavior of Magnesium‐Alloys for Automotive Applications under Mechanical and Environmental Loading: Influence of Passivating Films and Mechanisms of Local Breakdown To assure an efficient design of components under cyclic loading, all available data concerning fatigue have to be observed. Therefore the influences of manufacturing on the material condition, the mechanical loads and environmental effects have to be analysed. Magnesium‐alloys are of special interest for lightweight applications because of their excellent strength‐density ratio. The corrosion resistance of magnesium‐alloys depends on the same factors that are critical to other metals. The alloys have a good stability to atmospheric exposure and a good resistance to attack by alkali, chromic and hydrofluoric acids. However, because of the electrochemical activity of magnesium, the relative importance of some factors is greatly amplified. The nature and composition of passive films formed on magnesium‐alloys depend on the prevailing conditions, viz. alloy‐composition, passivation potential, pH, electrolyte composition and temperature. Passive films may be damaged by local breakdown. Because of this, magnesium‐alloys suffer a degradation of their properties when exposed to an aqueous environment. The main topic of the present investigations is the verification of mechanisms of the local breakdown of the protecting film. At least two mechanisms are possible for this localization: mechanical breakdown by slip steps and electrochemical breakdown (for e.g. by the effects of chloride ions). Corrosion and passivation of different high purity alloys have been studied in different solutions (neutral, alkaline with specific anions and cations) using electrochemical techniques. The diecasted alloys were tested as produced and machined. The results clarified that depending on alloy/material and surface condition/corrosion environment different mechanisms for electrochemical breakdown of the protecting films are possible. Hence fatigue life under environmental loading is influenced by surface and testing conditions.     

Untersuchung der Verteilung und Intensität filamentierter Barrierenplasmen für die Behandlung von Oberflächen

The application of barrier discharges at atmospheric pressure in air expands on the market of plasma technology, because it is an ecological and cost‐effective alternative to other processes of surface treatment. These plasmas usually consist of a multitude of spatially and temporally localized filaments, whose distribution should be as even as possible for homogeneous treatment. This holds especially for the plasma treatment of sensitive goods such as wool or other textiles. In equipment for continuous pass of material the barrier arrangements often consist of a system cylinder – cylinder or cylinder – plane, whereby the gap width changes locally. Space distribution and intensity of filaments has been investigated by means of short‐time photography and spatially resolved measurement of current distribution and energy distribution derived from it. The local dependency found can be explained by means of a capacitive equivalent circuit.     

Synthesis of amphiphilic magnetic microspheres by dispersion copolymerization of styrene and poly(ethylene oxide) macromonomer

Amphiphilic magnetic microspheres ranging in diameter from 5 to 100 µm were prepared by dispersion copolymerization of styrene and poly(ethylene oxide) vinylbenzyl (PEO‐VB) macromonomer (MPEO) in the presence of Fe₃O₄ magnetic fluid. The effects of various polymerization parameters on the average particle size were systematically investigated. The average particle size was found to increase with increasing styrene concentration and initiator concentration. It also increased with decreasing stabilizer concentration and molecular weight of MPEO. The content of the hydroxyl groups localized in the microspheres ranged from 0.01 to 0.2 mmol g^?1. © 2003 Society of Chemical Industry     

On the linear correlation between microhardness and mechanical properties in polar polymers and blends

The tensile elastic modulus (E), yield stress (σ_Y) and microhardness (MH) of neat and binary and ternary blends of glassy semicrystalline ethylene–vinyl alcohol copolymer (EVOH), a glassy amorphous polyamide and a semicrystalline nylon‐containing ionomer covering a broad range of properties were examined. The tests were carried out on dry and water‐equilibrated samples to produce stiffer and softer materials, respectively. From the results, more accurate linear correlations were found to describe adequately the microhardness, modulus and yield stress of these strongly self‐associated polymers through hydrogen bonding. Copyright © 2003 Society of Chemical Industry     

Co-digestion of manure and biowaste according to the EC animal by-products regulation and Finnish national regulations.

The objective of this study was to compare methane production and characteristics of digested material in anaerobic digestion concepts according to the Animal By-Products Regulation (ABP-Regulation) of the EC (hygienisation of biowaste for 1 hour at 70 degrees C, particle size < 12 mm) and Finnish national regulations (treatment temperature 55 degrees C, feeding interval 24 h, hydraulic retention time (HRT) 20 d, particle size < 40 mm) and with small variations in treatment methods for treating manure and biowaste. Moreover, the survival of three different salmonella bacteria in these processes was studied. Hygienisation of biowaste prior to digestion at 35 degrees C enhanced methane production by 14-18% compared to similar treatment without hygienisation. The differences in treatment temperature, HRT and hygienisation of biowaste prior to digestion did not significantly affect the characteristics of digested material. The concepts according to the ABP-Regulation and Finnish national regulations were effective in destroying salmonella bacteria to an undetectable level.     

Performance of thermostatic and electronic valves controlling the compressor capacity

The performance of the energy consumption of an electronic valve and a classical thermostatic valve has been compared when these expansion valves are adopted in a vapour compression plant subjected to a cold store. The main aim is to verify experimentally which type of expansion valve would be preferable from energy point of view when a classical thermostat or a fuzzy logic algorithm are used as the control system for the refrigeration capacity. The fuzzy logic‐based control is able to modulate continuously the compressor speed through an inverter. The results show that with a fuzzy algorithm, the thermostatic expansion valve allows an energy saving of about 8% in comparison with the electronic valve. When on–off control is used, the electric energy consumption obtained both with the electronic valve and with the thermostatic valve is comparable. Copyright © 2006 John Wiley & Sons, Ltd.