Evaluation of Polyester Resin as a New Compatibilizer for SBR/PVC Blends

A polyester (PE) based on the glycolyzed products of PET was prepared and added in different concentrations to a series of SBR/PVC blends. The addition of the polyester showed that all properties of SBR/PVC blends were improved by incorporation of PE. Highest mechanical strength values were obtained at a polyester concentration of 7.5 phr. Thermal analysis as well as dynamic mechanical properties of SBR/PVC blends after the addition of 7.5 and 10 phr polyester indicated one single glass transition temperature. The dielectric losses (?") were analyzed in the frequency domains in the two terms of Fröhlich related to the Maxwell Wagner effect and the orientation of the aggregates caused by the movement of the main chain. The permittivity (?') values were found to increase by increasing the polyester content. This increase was followed by a decrease in the ?" up to a 7.5 phr polyester content after which no pronounced change was noticed.     

On the ‘curiosity’ of electrical self‐heating,static charge and electromagnetic shielding effectiveness from carbon black/aluminium flakes reinforced epoxy‐resin composites

This paper shows the wide application range (such as electrical self‐heating and electromagnetic shielding effectiveness) of composites consisting of conductive carbon black/aluminum flakes (CBA) filler and epoxy insulative matrix. The effect of CBA content on the network structure of epoxy matrix was investigated in detail. Static electrical conductivity increases linearly with the increase of filler concentration at the interface in epoxy composites. The large decrease of the conductivity as a function of the temperature is analyzed in terms of the negative temperature coefficient of conductivity (NTCC) effect. The influence of viscosity, surface energy and barrier highest energy on the NTCC behaviour in the composite is also considered. Based on these results, a new interpretation is proposed to explain the NTCC phenomena by computing the swelling force among conductive phases. The correlations of conductivity during the temperature cycling and activation energy were analyzed. The effects of dynamic ageing at various temperatures on the resistivity are reported. Current–voltage–temperature characteristics for epoxy with different contents of CBA were examined in detail. A model based on the law of energy conservation is proposed to calculate the specific heat and amount of heat dissipation. The static charge of the epoxy–CBA composites was estimated. The correlation between electromagnetic wave‐shielding effectiveness (EMS), conductivity and frequency of epoxy composites with different filler contents is also discussed. Furthermore, the effect of annealing on EMS of epoxy composites was examined. © 2002 Society of Chemical Industry     

Exploration of mesoporous structure of tunisian raw and acid-leached phosphate ore particles

Rock phosphate fractions were examined for their porous structure by nitrogen adsorption. The pore size distribution and the shape of pores does not seem to depend on the particle size. The specific surface area values present two regions, one above and one below that of the particles with 125 μrn diameter. Particles of a given size were leached with dilute phosphoric acid (1.5 mass% P₂O₅) at 25°C. It was observed that there is a widening of the initial pores during leaching. The particles collected at the initial period of the reaction are pitted and those collected at the final period are disintegrated.     

Investigation of conductivity characteristics of nitrile butadiene rubber vulcanizates filled with semiconducting carbide ceramic

SiC‐ and B₄C‐filled NBR rubber composites were prepared with various volume fractions of filler by a conventional roll‐mill method. The morphological structures of the NBR–SiC and NBR–B₄C composites were analyzed by scanning electron microscopy. The dependence of room‐temperature volume resistivity (ρ_v) on the concentration of filler in the two systems was studied. In addition, variation in the number of current carriers (n), mobility carriers (μ), dielectric constant (ε), and dielectric loss factor (tan δ) on filler concentration in the two systems were investigated in detail. The applicability of composites as negative temperature coefficient (NTCR) linear thermistors was studied by the dependence of volume resistivity on temperature. The resistivity showed negative temperature dependence and changed linearly with temperature parallel. The conduction mechanism of the conductivity of the two composites was analyzed in terms of the computed activation energy and hopping energy. Change in volume resistivity as a function of frequency for the two systems was also investigated. Finally, the dependence of volume resistivity on applied pressure and possible real applications of these composites as transducers in pressure sensors were also studied. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2158–2165, 2007     

Electrical conductivity of concrete containing silica fume

The influence of silica fume on concrete properties represents an important technical research. In general, silica fume tends to improve both mechanical characteristics and durability of concrete. Thus the electrical properties of concrete containing silica fume can be studied to clarify its physical performance during hydration. The electrical conductivity of neat cement, mortar and concrete pastes was measured during setting and hardening. The ordinary Portland cement was partially replaced by different amounts of silica fume by weight. The changes in the electrical conductivity were reported during setting and hardening after gauging with water. The results of this study showed that the electrical conductivity can be used as an indication for the setting characteristics as well as the structural changes of the hardened pastes made with and without silica fume.     

Yield response of lentil to directly applied and residual phosphorus in a Mediterranean environment

The response of lentil grown under rainfed conditions to directly applied and residual phosphorus (P) was described by a modified Mitscherlich equation, accounting for the effects of rainfall on (1) potential yield, and (2) the availability of soil-P to the crop. The response of lentil yield to directly applied and residual P was studied in two-course cereal–lentil rotational trials under rainfed conditions in a Mediterranean-type environment. Cereal crops were grown at different P application rates during 4 growing seasons at 3 sites, representing different rainfall zones in northwest Syria. Lentil (Lens culinaris Med.) was grown during 4 seasons at the same sites, each lentil crop following a cereal crop. In 3 out of 4 lentil-growing seasons, additional P was applied to lentil in subplots to compare the residual and direct effects of P application. The initial contents of extractable soil-P (P-Olsen) were low at all sites, in the range of 2–5 ppm P. Under the conditions of the experiments, lentil appeared to benefit slightly more from P applied to the preceding wheat crop (residual P) than from directly applied P. It is shown that the modified Mitscherlich equation could be used as a basis for P fertilizer recommendations for rainfed farming. As for lentil, it was concluded that a single application of P to the wheat crop in a wheat/lentil rotation could reduce the cost of lentil production, without reducing lentil yield.     

Time optimization of ultraviolet–ozone pretreatment for improving wool fabrics properties

Wool fabrics were exposed to ultraviolet (UV)–ozone treatment for different periods. After exposure, the fabrics were analyzed by Fourior transform infrared spectroscopy (FTIR). Also, the crystallinity and amorphousity regions were followed by an X‐ray diffraction technique. The results were correlated by mechanical properties measurements. After a certain period of exposure, the dyeability and printability were improved because these abilities are strongly related to the percentage ratio of crystallinity regions to amorphousity regions in wool fabrics. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1469–1476, 2002     

Temperature and processing effects on lithium ion conductivity of solution-deposited lithium zirconium phosphate (LiZr2P3O12) thin films

Lithium zirconium phosphate (LiZr₂P₃O₁₂) thin films have been prepared on platinized silicon substrates via a chemical solution deposition approach with processing temperatures between 700°C and 775°C. Films that were subject to a single high-temperature anneal were found to crystallize at temperatures above 725°C. Crystallization was observed in films annealed after each deposited layer at 700°C and above. In both cases, grain size was found to increase with annealing temperature. Ion conductivity was found to increase with annealing temperature in singly annealed films. In per-layer annealed films ion conductivity was found to initially increase then decrease with increasing annealing temperature. A maximum ion conductivity of 1.6 × 10⁻⁶ S/cm was observed for the singly annealed 775°C condition, while a maximum ion conductivity of 5.8 × 10⁻⁷ S/cm was observed for the 725°C per-layer annealed condition. These results are consistent with an increasing influence of cross-plane, internal interface resistance and vapor phase carrier loss in the per-layer annealed samples. This work demonstrates that post-deposition processing methods can strongly affect the ion conducting properties of LiZr₂P₃O₁₂ thin films.     

Great enhancement of mechanical features in PLA based composites containing aligned few layer graphene (FLG), the effect of FLG loading,size, and dispersion on mechanical and thermal properties

Four series of polylactide (PLA) based composite films containing horizontally aligned few layer graphene (FLG) flakes of high aspect ratio and adsorbed albumin are prepared. The mechanical and thermal properties varies with percentage, dispersion degree and size of FLG flakes. Great improvement up to 290% and 360% of tensile modulus and strength respectively were obtained for the composite containing high lateral size of FLG at 0.17% wt, and up to 60% and 80% for the composite with very well dispersed 0.02% wt FLG. The composites of PLA and PEG-PLLA containing very well dispersed FLG flakes at 0.07% wt are ductile showing enhancement of elongation at break up to respectively 80% and 88%. Relatively high electrical conductivity, 5 × 10⁻³ S/cm, is measured for PLA film charged with 3% of FLG.     

Crack growth angle prediction of an internal crack under mixed mode load for unfilled elastomer using the strain energy density factor

This article investigates the prediction of the crack growth angle of an existing internal crack under mixed mode loading at the crack tip for an unfilled ethylene propylene diene terpolymer rubber (EPDM). For the realization of mixed mode loading, the cracks of the uniaxial loaded specimens were oriented with different angles to the loading direction. The energy density factor was used as a potential criterion for determining the crack growth angle. The determination of the strain energy density factor was carried out simulatively in Abaqus. The second-order Ogden model was used to describe the rubber-like material behavior. The relative local minimum of the strain energy density factor provides the possible growth angle. The experimental investigations show that the initial cracks grow orthogonally to the loading direction for the different crack orientation angles. For the crack orientation angle parallel to the load direction, the crack growth was observed because the strong stretching of the specimen caused strong necking in the crack region. The crack growth for the remaining crack orientation angles were induced due to shear loading at the crack tip. The predictive angle of different crack orientation angles shows very good accordance to the measured crack growth angles.