Structural development and magnetic phenomenon in Zn–Cr–Fe multi oxide nano-crystals

The Cr³⁺ ions doped multi-oxide ZnFe_2−xCr_xO₄ ferrite nanoparticles have been synthesized by chemical co-precipitation method. Site occupancies of Zn²⁺, Cr³⁺ and Fe³⁺ ions were analyzed using X-ray diffraction data and Buerger's method. The effect of the constituent phase variation on the magnetic hysteresis behavior was examined by saturation magnetization which decreases with the increase in Cr³⁺ content in place of Fe³⁺ ions at octahedral B-site. Typical blocking temperature (T_B) around 90 K was observed by zero field cooling and field cooling magnetization study. Room temperature Mössbauer spectra show two paramagnetic doublets (tetrahedral and octahedral sites). The isomer shifts of both doublets decrease whereas quadrupole splitting and relative area of tetrahedral A-site increases with increasing Cr³⁺ substitution. The dielectric constant (measured on compositions x=0, 0.4, 0.8 and 1.0) increases when the temperature increases as in the semiconductor. This behavior is attributed to the hopping of electrons between Fe²⁺ and Fe³⁺ ions with a thermal activation.     

Performance analysis of three advanced controllers for polymerization batch reactor: An experimental investigation

The performances of three advanced non-linear controllers are analyzed for the optimal set point tracking of styrene free radical polymerization (FRP) in batch reactors. The three controllers are the artificial neural network-based MPC (NN-MPC), the artificial fuzzy logic controller (FLC) as well as the generic model controller (GMC). A recently developed hybrid model (Hosen et al., 2011a. Asia-Pac. J. Chem. Eng. 6(2), 274) is utilized in the control study to design and tune the proposed controllers. The optimal minimum temperature profiles are determined using the Hamiltonian maximum principle. Different types of disturbances are introduced and applied to examine the stability of controller performance. The experimental studies revealed that the performance of the NN-MPC is superior to that of FLC and GMC.     

The effect of di-2-ethylhexyl phthalate on the thermo-oxidative ageing of poly(vinyl chloride)/epoxidized natural rubber blends

The effect of di-2-ethylhexyl phthalate (DOP) plasticizer on the degradation behaviour of 50/50 poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blend was studied by long-term exposure to ambient conditions (27–30°C) in the laboratory. While the unplasticized blend showed obvious changes in physical properties such as hardening, loss of elasticity and embrittlement, the plasticized blend retained its properties. Thermo-oxidative ageing studies were carried out by evaluating the mechanical properties before and after ageing in an air oven at 80°C for 168 h. The relatively rapid degradation of PVC/ENR blend has been attributed to the high concentration of epoxy groups and the occurrence of ring-opening reactions to form ether crosslinks. It was found that the plasticizer confers adequate stabilization upon the addition of a certain threshold amount. The optimum amount of plasticizer required to adequately stabilize the blend is 20 phr. Above this there is a tendency for plasticizer migration to occur. The use of an antioxidant in conjunction with the plasticizer further stabilizes the blend. The general trend is of decrease in mechanical and physical properties with increase in DOP concentration. In addition, ease of processing also increases as indicated by the torque maxima and minima obtained from the Brabender plastograms.     

Mechanical and thermo-oxidative properties of blends of poly(vinyl chloride) with epoxidized natural rubber and acrylonitrile butadiene rubber in the presence of an antioxidant and a base

Being polar and compatible with poly(vinyl chloride), epoxidized natural rubber (ENR) is similar in behaviour to acrylonitrile butadiene rubber (NBR). To assess the extent of this similarity, the mechanical properties of 50/50 blends of PVC with these two rubbers were compared. Their response to thermo-oxidative ageing in the presence of an antioxidant and a base was also investigated by ageing the blends at 100°C for 7 days. Studies involving mechanical properties and FTIR were used to evaluate the extent of thermal degradation. The results revealed that blends of ENR show mechanical properties which are as good as, and in some instances better than, those of the NBR blends. However, the ENR blends with PVC are very prone to oxidative ageing. This might be attributed to the susceptibility of the oxirane group to ring-opening reactions, particularly in the presence of PVC, which yields HCl as it degrades. The amine-type antioxidant 2,24-trimethyl-1,2-dihydroquinoline (TMQ) improved the oxidative stability of both blends. This was more significant in the ENR blend, which in some cases attained stability comparable with that of NBR. The addition of a base, calcium stearate [Ca(St)₂], did not show any influence in the PVC/ENR blend, even though it was expected to curb acid-catalysed degradation. Ca(St)₂, however, improved the oxidative stability of the PVC/NBR blend. The combination of optimum amounts of TMQ and Ca(St)₂ effectively improved the tensile strength of both unaged blends, without appreciable adverse effect on elongation at break. This combination also imparted stability better than that of TMQ alone.     

Distribution of Partial Digestion Products of Hydroxypropyl Derivatives of Maize (NM), Waxy Maize (WM) and High Amylose (HA) Maize Starches

Porcine pancreatic α-amylase digests of native and hydroxypropyl derivatives of maize, waxy maize and high amylose maize starches were subjected to ethanolic fractionation into oligosaccharide and polysaccharide fractions. Both fractions of the partial digests were analysed for blue values, reducing values, total carbohydrate, average degree of polymerisation and molar substitution (MS). Distribution of hydroxypropyl groups between the fractions varied depending on starch type and level of substitution with the polysaccharide fraction being higher in MS. Blue values (BV) and average degree of polymerisation (DP) tended to decrease with digestion while reducing (RV) increased.     

Effect of pH,Temperature and Reaction Time on Calcium Binding by Hydroxypropyl Rice Starches

Calcium binding by both native and hydroxypropyl starches was studied in aqueous media under different pH, temperature and reaction times at various calcium: starch ratios. Calcium binding was markedly influenced by pHs and temperatures of the reaction mixture. Reaction times did not show marked influence on calcium binding. Maximum calcium binding was observed in alkaline pH and at lower temperature. Most of the calcium bound within the first 20 minutes. Thus, alkaline pH and lower temperature is more favourable for calcium binding by both native and hydroxypropyl rice starches compared to acidic pH and higher temperatures.     

Ergogenic Attributes of Young and Mature Coconut (Cocos nucifera L.) Water Based on Physical Properties,Sugars and Electrolytes Contents

The present work aimed to compare the main ergogenic attributes of two commercialized stages (young and mature) of coconut water (CW) obtained from four coconut varieties. The changes of electrolytes and sugars in CW upon maturation were quantified by inductively coupled plasma mass spectrophotometer and high-performance liquid chromatography, respectively. Based on the electrolyte profiling, potassium yielded the highest amount (ranging from 237.41 to 361.20 mg/100 mL) followed by sodium, magnesium, calcium, iron, manganese, copper, selenium, and zinc across all the maturity stages tested. For sugars, there were lower amounts of fructose and glucose, but a higher amount of sucrose with the maturation of the fruits. In conclusion, the amount of beneficial nutrients in the form of sugars and minerals was higher than that of young CW, and the ergogenic attributes of mature CW especially from MATAG variety (M-MATAG) were the best to be exploited further in the development of natural energy drinks.     

Hypocholesterolaemic effect of yoghurt containing Bifidobacterium pseudocatenulatum G4 or Bifidobacterium longum BB536

The effect of a yoghurt supplement containing Bifidobacterium pseudocatenulatum G4 or Bifidobacterium longum BB536 on plasma lipids, lipid peroxidation and the faecal excretion of bile acids was examined in rats fed a cholesterol-enriched diet. After 8 weeks, the rats in the positive control (PC) group who were fed the cholesterol-enriched diet showed significant increases in plasma total cholesterol (TC), low-density lipoprotein (LDL) cholesterol, and malondialdehyde (MDA). However, groups fed a cholesterol-enriched diet supplemented with yoghurt containing B. pseudocatenulatum G4 or B. longum BB536 had significantly lower plasma TC, LDL-C, very-low-density lipoprotein (VLDL) cholesterol, and MDA than had the PC group after 8 weeks of treatment. In addition, faecal excretion of bile acids was markedly increased in the rats fed the yoghurt containing B. pseudocatenulatum G4 or B. longum BB536 as compared to the PC and NC groups.     

Occurrence of phthalate metabolites in human urine from several Asian countries

The occurrence of 14 phthalate metabolites was found in human urine samples collected from seven Asian countries: China, India, Japan, Korea, Kuwait, Malaysia, and Vietnam. Phthalate metabolites were found in all samples, indicating widespread exposure of humans to phthalates in these Asian countries. The highest total (the sum of 14 phthalates) phthalate metabolite concentrations were found in samples collected from Kuwait (median: 1050 ng/mL), followed in decreasing order by samples from India (389 ng/mL), China (234 ng/mL), Vietnam (133 ng/mL), Japan (120 ng/mL), Korea (117 ng/mL), and Malaysia (94.9 ng/mL). The creatinine-adjusted median concentrations of total phthalates for urine samples from Kuwait, India, China, Vietnam, Japan, Korea, and Malaysia were 692, 506, 289, 119, 103, 104, and 169 μg/g creatinine, respectively. Monomethyl phthalate (mMP), monoethyl phthalate (mEP), mono (2-isobutyl phthalate) (miBP), mono-n-butyl phthalate (mBP), and metabolites of di-(2-ethylhexyl) phthalate (DEHP) were the dominant compounds, collectively accounting for >95% of the total concentrations in the samples from the seven countries. The profiles of urinary phthalate metabolite concentrations varied among the samples collected from the seven countries. Urine samples from Kuwait contained the highest concentrations of mEP (median: 391 ng/mL), mBP (94.1 ng/mL), and the metabolites of DEHP (202 ng/mL), whereas samples from China and Japan contained the highest concentrations of miBP (50.8 ng/mL) and mMP (17.5 ng/mL), respectively. mEP was the predominant metabolite in urine samples from India and Kuwait (accounting for 49% of the total), mBP and miBP were the predominant compounds in samples from China (52%), and DEHP metabolites were the predominant compounds in samples from Korea (46%) and Vietnam (52%). Based on the urinary concentrations of mEP, mBP, miBP, and DEHP metabolites of the samples from the seven Asian countries, we estimated daily intake rates of diethyl phthalate (DEP), dibutyl phthalate (DBP), and DEHP. The results indicated that people in the seven Asian countries are exposed to DEP, DBP, and DEHP at levels well below the reference doses (RfD) suggested as unsafe by the U.S. Environmental Protection Agency (EPA). The estimated exposure doses to DEHP in Kuwait, however, were above the RfD recommended by the EPA.     

Structural Control of NiO–YSZ/LSCF–YSZ Dual‐Layer Hollow Fiber Membrane for Potential Syngas Production

The objective of this study was to fabricate dual‐layer hollow fiber as a microreactor for potential syngas production via phase inversion‐based co‐extrusion/cosintering process. As the main challenge of phase inversion is the difficulty to obtain defect‐free fiber, this work focuses on the effect of the fabrication parameters, that is, nonsolvent content, sintering temperature and outer‐layer extrusion rate, on the macrostructure of the produced hollow fiber. SEM images confirm that the addition of nonsolvent has successfully minimized the finger‐like formation. At high sintering temperature, more dense hollow fiber was formed while outer‐layer extrusion rate affects the outer layer thickness.