One-dimensional diffuser based on a thick layer of dichromated gelatin

A new diffuser capable of scattering light in one direction (one-dimensional diffuser) has been developed and experimentally tested. The diffuser is formed in a thick layer of dichromated gelatin. The scattering indicatrices of the diffuser measured in two mutually perpendicular directions are presented. It is demonstrated that the indicatrix width in one direction is significantly greater than that in the perpendicular direc-tion. However, no zero-order diffraction has been observed. The proposed one-dimensional diffuser exhibits close scattering indicatrices for reading at a wavelength of 0.44 and 0.63 μm.     

British female academics and comparative psychology: Attempts to establish a research niche in the early 20th century.

Why was there a preponderance of women engaged in laboratory-based studies of animal behavior in Britain in the early years of the 20th century? As a new experimental subject with recently neglected potential, animal psychology then represented an opportunity for women to make further inroads into academic science. Because the study of psychology before World War I offered negligible professional opportunities for the application of the subject, the intake of students was restricted. Perhaps this encouraged academic access to it by aspiring female scientists who felt that career prospects, uncertain and socially unexpected of them in any case, were worth chancing for greater long-term rewards. The academic circumstances and contributions of 3 British female pioneers in experimental comparative psychology are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Grain refinement of Al-7Si alloys and the efficiency assessment by recognition of cooling curves

Under sand cup solidification condition, the influence of Ti, B concentration, and holding time on the grain size of a high-purity Al-7Si alloy has been systematically studied. It is found that the grain size decreases rapidly at lower Ti or B additions, and is almost constant at the higher concentrations. For Al-3B refined Al-7Si alloys, the grain size increases at the initial period of holding time, and then rapidly becomes independent of holding time; while for Al-7Si alloys refined with Al-5Ti-1B, the grain size increases with holding time throughout. To evaluate the refinement efficiency, a new method named “intelligent evaluating of melt quality by pattern recognition of thermal analysis cooling curves” has also been introduced in this article. The results show that comparing the cooling curve of the evaluated melt with those in a database to find the most similar one to it can precisely assess the grain refinement efficiency of the measured Al-7Si alloy. In addition, the influence of Ti, B addition levels, and pouring temperatures on some characteristic parameters of cooling curve has also been discussed.     

Electrospray droplet sources for thin film deposition

Electrospraying utilises electrical forces for liquid atomisation. Droplets obtained by this method are highly charged to a fraction of the Rayleigh limit. The advantage of electrospraying is that the droplets can be extremely small, down to the order of 10’s nanometres, and the charge and size of the droplets can be controlled to some extent be electrical means. Motion of the charged droplets can be controlled by electric field. The deposition efficiency of the charged spray on an object is usually higher than that for uncharged droplets. Electrospray is, or potentially can be applied to many processes in industry and in scientific instruments manufacturing. The paper reviews electrospray methods and devices, including liquid metal ion sources, used for thin film deposition. This technique is applied in modern material technologies, microelectronics, micromachining, and nanotechnology.     

Effect of deformation route on microstructural development in aluminum processed by equal channel angular extrusion

Aluminum has been deformed by equal channel angular extrusion (ECAE) to obtain submicron-grained structures under different deformation routes. The deformation routes were varied by rotating billets through 0, 90, and 180 deg between each extrusion pass, and were designated as route A, B_C, and C, respectively. Based on quantitative microstructural analysis, the effectiveness of the deformation route is shown to depend upon the different definition used. The order of effectiveness is (a) A > B_C > C for both 90 and 120 deg dies, in terms of the generation of high-angle grain boundaries (HAGBs); (b) B_C > C > A for both 90 and 120 deg dies, in terms of the formation of equiaxed shape of grains; and (c) B_C > A > C for 90 deg die and B_C ∼ A > C for 120 die, in terms of reducing grain size. It is suggested that the generation of HAGBs can be related to the accumulation of nonredundant strain, while the shape and orientation of grains may be linked to the shearing patterns of the deformation route.     

Static and pulsed pressures measured using electrically conducting rubbers

A method of measuring static and pulsed pressures using electrically conducting rubber sensors is proposed. The method is based on a change in the volume resistivity of a filled rubber under the action of external pressure. The pressure-induced change in resistance of the rubber sensor is proportional to the applied pressure and can be measured by a bridge circuit. Using this method, it is possible to evaluate the degree of homogeneity of the pressure distribution over a solid surface. This is achieved by distributing rubber sensors over the given surface.     

Copper-zirconium tungstate composites exhibiting low and negative thermal expansion influenced by reinforcement phase transformations

A fully-dense Cu-75 vol pct ZrW₂O₈ metal matrix composite was fabricated by hot isostatic pressing of Cu-coated ZrW₂O₈ particles. A small amount of the high-pressure γ-ZrW₂O₈ phase was created during the cooldown and depressurization following densification; near complete transformation to γ-ZrW₂O₈ was achieved by subsequent cold isostatic pressing. The thermal expansion behavior of the composite between 25°C and 325°C was altered by the cold isostatic pressing treatment, and also depended on the length of time that had passed between thermal cycles. The measured thermal expansion coefficients within specific temperature ranges varied from −6·10⁻⁶ K⁻¹ to far above the thermal expansion coefficient of the copper matrix. The complex temperature-dependent expansion/contraction behavior could be justified by considering the evolution of phase transformations taking place in the ZrW₂O₈ phase, which were observed by in-situ synchrotron X-ray diffraction measurements.     

Study of phase equilibria in the Al - Pd - Re system

Scanning and transmission electron microscopy have been combined with x-ray diffraction to examine the phase equilibria in the Al - Pd - Re system at 1000°C for compositions from 50 to 100 at.% Al, and the corresponding isothermal section has been constructed. The binary monoclinic Al₃ Re phase has been observed for the first time. It is confirmed that there is a stable icosahedral phase in this system. The boundaries to its homogeneity region have been determined and the phase equilibria in which it participates.     

Anaerobic biodecolorization of textile reactive anthraquinone and phthalocyanine dyebaths under hypersaline conditions.

The biological decolorization of two industrial, spent textile reactive dyebaths was investigated using a suspended-growth, halophilic mixed culture fed with glucose. Dyebath I contained mainly Reactive Blue 19 (RB19), an anthraquinone dye, whereas dyebath II contained mainly Reactive Blue 21 (RB21), a phthalocyanine dye. Batch assays under anaerobic conditions with the two neutralized dyebaths resulted in 87 and 37% extent of decolorization for dyebaths I and II, respectively. The rate of glucose utilization and the extent of acetate production were impacted in the presence of each dyebath as compared to the control culture. However, dyebath decolorization occurred despite moderate culture inhibition. Reuse of a biologically renovated RB19-containing dyebath in the dyeing process resulted in reproducible but not identical cotton fabric shades as compared to a standard dyeing (i.e., control) using fresh water. This difference is attributed to a variable degree of RB19 aggregation during the dyeing process and is not related to the efficiency of the biodecolorization process. Further improvement of the redyeing efficiency will lead to the development of an in-plant, closed-loop decolorization system resulting in significant water conservation and minimization of textile pollutants such as salt and dyes.     

Analysis of the possibility of implementing the principle of redistribution of concentration fields for reactive distillation processes

The evolution of the phase portrait for the dynamic system of open evaporation combined with a chemical reaction for a fixed liquid amount was studied as dependent on the rate constants of the reaction. A three-component azeotropic mixture whose vapor-liquid equilibrium diagram is characterized by two distillation regions was considered. The possibility of the open evaporation trajectory to transfer through the separatrix between the distillation regions was shown, as well as the possibility of implementing the principle of redistribution of the concentration fields due to chemical reactions occurring in reactive distillation columns.Translated from Teoreticheskie Osnovy Khimicheskoi Tekhnologii, Vol. 39, No. 2, 2005, pp. 115–119.Original Russian Text Copyright © 2005 by Solokhin, Nazanskii, Timofeev.