Production technology for low-carbon,low-sulfur boron steel

A technology for slag formation in the ladle–furnace unit is considered; the slag is based on the CaO–SiO₂–MgO–Al₂O₃–B₂O₃ system. This technology permits both microalloying of the steel with boron (reduced from the oxide phase) and desulfurization of the steel. The resulting boron content in the steel is 0.001–0.008%; the sulfur content in low-alloy steel and pipe steel is low (0.004–0.010%); and the consumption of manganese ferroalloys is reduced to 0.5 kg/t for 08кп steel and 1.4 kg/t for 09Г2C steel. In addition, the proposed technology increases the strength of the rolled steel, without loss in its plasticity; and reduces the environmental impact thanks to the replacement of fluorspar by colemanite.     

Ga-doped IZO films obtained by magnetron sputtering as transparent conductors for visible and solar applications

C-axis textured thin films of gallium-doped indium zinc oxide (GIZO) with a 2% ratio of Ga/Zn, were obtained via RF-magnetron sputtering with high transparency and electrical conductivity. A Box-Behnken response surface design was used to evaluate the effects of the deposition parameters (In₂O₃ target power, deposition time, and substrate temperature) on the chemical composition, optical, electrical, and structural properties of the GIZO films. The optical constants and the electrical properties were obtained using optical models. The GIZO stoichiometry, and therefore the In/Zn atomic ratio, affected the crystallinity, crystalline parameters, band gap, and charge carrier mobility of the GIZO films. The charge carrier density was related to the change in the crystalline parameters of the hexagonal structure and the In/Zn atomic ratio. The best electrical conductivity values (1.75?×?10³ Ω^?1 cm^?1) were obtained for GIZO films with In/Zn ratio ≥?1. Several figures of merit (FOM) defined for the visible and solar regions were comparatively used to select the optimal In/Zn atomic ratio that provided the best balance between the conductivity and the transparency. The optimal In/Zn ratio was in a range of 0.85–0.90 for the GIZO films.     

Modeling the Motion of a Saw Ginning Machine

The dynamic characteristics of a saw gin as a subsystem with lumped and distributed parameters are considered in the paper. On the basis of investigation of the machine assembly, graphs are drawn that allow establishing the maximum values of the angle of relative rotation and the angle of rotation of the saw cylinder shaft under torsion.     

Towards Diastereomeric Pure Salts with Antisolvent Methods

Chiral molecules, especially enantiomers and diastereomers of purity > 99 %, present a significant market share within the chemical, pharmaceutical, and flavor industries. Antisolvent precipitations, both batch and semicontinuous operations to serve the current trends in flow chemistry were demonstrated to be environmentally benign and efficient tools in achieving high optical purities. Although salts are known to be insoluble in supercritical CO₂, instabilities of the nascent salts were detected and applied for increasing efficiency. Diastereomeric excess values of the crystalline products exceeded 99 % in maximum of three consecutive steps both by repeated resolution with half molar equivalent of the amine to the acid and by direct recrystallization of the salts.     

A simple model for the semicontinuous heterophase polymerization: Ethyl methacrylate as a case example

A simple but comprehensive model considering homogeneous and micellar nucleation, coagulation, entry of radicals to particles and to micelles and radicals' exit from particles, is presented. The model is validated, in a starved semicontinuous heterophase polymerization of ethyl methacrylate, at three monomer addition rates. The model accurately describes the overall and instantaneous conversion, the average particle density and diameter, and the number and weight average molar masses evolutions over time. It is found that even though the average number of radicals is much smaller than 0.5, the system is not 0-1. An empirical function was used to describe the gel effect. The homogeneous nucleation was the prevailing mechanism for particle formation and large exit rates of radicals were observed. POLYM. ENG. SCI., 60: 223–232, 2019. © 2019 Society of Plastics Engineers