The growth of ambient aerosols in the conditions of the respiratory system

The effect on ambient aerosols of exposure to the conditions of the respiratory system was determined by sampling simultaneously through two dichotomous samplers in parallel. In one of the samplers the aerosol was brought to 37°C and near 100% relative humidity before passing through the virtual impactor. The results show that, as a result of humidification, about 10–15% by mass of the aerosol which would normally been collected in the fine (less than 2.5 μm aerodynamic diameter) fraction of the sample grows sufficiently when humidified to be collected with the coarse fraction. It is suggested that the direct application to inhalation studies of dichotomous sampler results should be approached with some caution.     

Unsaturated polyesters. II. Structure and properties of polyester resins based on cinnamylsuccinic acid

Unsaturated Polyester resins were prepared by the reaction of cinnamylsuccinic acid with saturated diols, namely, ethylene, diethylene, propylene, dipropylene, tetramethylene, and hexamethylene glycols, and the unsaturated diols, namely, 1,4-butene- and 1,4-butynediols. All the polyester resins obtained have been characterized and were found to cure with styrene, with relatively low conversions. The properties of the cured polyesters in the form of films were determined. IR and ¹H-NMR spectroscopy were used for both qualitative and quantitative analyses of the polyesters and their hydrolyzate products, after curing with styrene.     

Experimental Procedure for Determining Transport Properties of Oxide Scales

To determine the transport properties of oxide scales growing on an alloy, a laboratory apparatus was developed which allows plotting of characteristic V = f (i) curves and oxidation with an applied electric field. The apparatus and formalism used are described; it appears that such experimental procedures allow determination of the mean ionic transport number, ti; the conductivity values σ, σ_i, and σ,_e; and the effective charge, Z*, of the moving species in the oxide scale (A1₂O₃ in the present case).     

Preparation of vanadyl porphyrin complexes from a metal-porphyrin petroleum concentrate and study of their catalytic activity

A mixture of vanadyl porphyrin complexes was obtained from a metal-porphyrin concentrate (MPC) isolated from crude petroleum by selective extraction. The petroleum MPC was subjected to demetallization and the subsequent introduction of the vanadyl cation into the porphyrin ring. It was shown that the mixture of vanadyl-porphyrin complexes obtained from MPC catalyzes the cyclohexene epoxidation reaction. On the basis of experimental data, it was assumed that the mechanism of olefin oxygenation in the presence of vanadyl porphyrin complexes is similar to the mechanism of the Prilezhaev epoxidation reaction of unsaturated compounds.     

Application of a multi-channel system for continuous monitoring and an early warning system.

A multi-channel continuous toxicity monitoring system developed in our laboratory, based on two-stage mini-bioreactors, was successfully implemented in the form of computer-based data acquisition. The multi-channel system consists of a series of a two-stage minibioreactor systems connected by a fiber optic probe to a luminometer, and uses genetically engineered bioluminescent bacteria for the detection of the potential toxicity from the soluble chemicals. This system can be stably and continuously operated due to the separation of the culture reactor from the test reactor and accomplish easy and long-term monitoring without system shut down by abrupt inflows of severe polluting chemicals. Four different recombinant bioluminescent bacteria were used in different channels so that the modes of the samples toxicities can be reasonably identified and evaluated based upon the response signature of each channel. The bioluminescent signatures were delivered from four channels by switching one at once, while the data is automatically logged to an IBM compatible computer. We also achieved the enhancement of the system through the manipulation of the dilution rate and the use of thermo-lux fusion strains. Finally, this system is now being implemented to a drinking water reservoir and river for remote sensing as an early warning system.     

Monitoring of human enteric viruses and coliform bacteria in waters after urban flood in Jakarta, Indonesia.

Floodwaters in Kampung Melayu village, Jakarta, Indonesia, as well as river water and consumable water (including groundwater and tap water) samples in flooded and non-flooded areas, were quantitatively analysed to assess occurrence of viruses and total coliforms and E. coli as bacterial indicators after flooding event. High numbers of enterovirus, hepatitis A virus, norovirus (G1, G2) and adenovirus were detected at high concentration in floodwaters and waters sampled from Ciliwung River which runs across metropolitan Jakarta and is used widely for agriculture and domestic purposes by poor residents. One out of three groundwater wells in the flooded area was contaminated with all viruses tested while no viruses were found in groundwater samples in non-flooded areas and tap water samples. The results revealed that human enteric viruses, especially hepatitis A virus and adenovirus, were prevalent in Jakarta, Indonesia. This study suggested that flooding posed a higher risk of viral infection to the people through contamination of drinking water sources or direct contact with floodwaters.     

Boosting nitrification by membrane-attached biofilm.

Nitrification is a key step for reliable biological nitrogen removal. In order to enhance nitrification in the activated sludge (AS) process, membrane-attached biofilm (MAB) was incorporated in a conventional activated sludge tank. Simultaneous organic carbon removal and nitrification of the MAB incorporated activated sludge (AS + MAB) process was investigated with continuous wastewater treatment. The effluent TOC concentration of AS and the AS + MAB processes were about 6.3 mg/L and 7.9 mg/L, respectively. The TOC removal efficiency of both AS and AS + MAB were above 95% during the wastewater treatment, indicating excellent organic carbon removal performance in both processes. Little nitrification occurred in the AS process. On the contrary, successful nitrification was obtained with the AS + MAB process with nitrification efficiency of about 90%. The volumetric and surface nitrification rates were about 0.14 g/Ld and 6.5 g/m2d, respectively. The results clearly demonstrated that nitrification in the conventional AS process was boosted by MAB. Furthermore, the microfaunal population in the AS + MAB process was different from that in the AS process. The high concentration of rotifers in the AS + MAB process was expected to decrease the generation of excess sludge in the process.     

Effect of grain boundaries on isothermal solidification during transient liquid phase brazing

The influence of liquid penetration at grain boundary regions on the rate of advance of the solid-liquid interface during isothermal solidification of transient liquid phase (TLP) brazed nickel joints has been examined. The test samples used in this study were Ohno-cast nickel with a grain size of >4 mm and a fine-grained nickel with a grain size of around 40 μm. Both Ni-base materials had the same chemical composition. The rate of isothermal solidification was greater when fine-grained nickel was employed during TLP brazing using Ni-11 wt pct P filler metal at 1200 °C. Liquid penetration at grain boundaries accelerates the isothermal solidification process by increasing the effective solid-liquid interfacial area and increasing the rate of solute diffusion into the base material. An analysis of electron channeling patterns has confirmed that random high-angle boundaries have a greater influence on the rate of isothermal solidification than ordered boundaries including small-angle or twin boundaries. Formerly Visiting Scientist, Department of Metallurgy and Materials Science, University of Toronto. Formerly Postdoctoral Fellow, Department of Metallurgy and Materials Science, University of Toronto     

Nanolayered lightweight flexible shields with multidirectional optical transparency

New nanolayered coatings are designed and deposited on flexible plastic substrate having the thickness of 100 /spl mu/m, in order to realize lightweight ultrathin transparent shielding foils. The structure of the coating is optimized considering three figures of merit: the average transmittance in the visible range for normal incidence, the normalized average transmittance for oblique incidence at 550 nm, and the transmittance quality factor. The nanotechnology exploited for the deposition of the transparent metals is the dual ion beam sputtering. Tests of durability, optical transmission, and shielding effectiveness demonstrate that the film has a high adhesion under mechanical solicitation, high resistance against aging, peak transmittance in the visible range higher than 70%, omnidirectional properties in the range 0/spl deg/-60/spl deg/, and shielding effectiveness of 40 dB up to 6 GHz.