A comparison between the axial flux and the radial flux structures for PM synchronous motors

The aim of this paper is the comparison of the axial flux (AF) structures versus the conventional radial flux (RF) structures for permanent-magnet synchronous motors. The comparison procedure is based on simple thermal considerations. Two motor typologies are chosen and compared in terms of delivered electromagnetic torque. The comparison is developed for different motor dimensions and the pole number influence is put into evidence. The paper reports the complete comparison procedure and the related results analysis. The obtained results show that, when the axial length is very short and the pole number is high, the AF motors can be an attractive alternative to the conventional RF solutions.     

Incremental transmission loss allocation under pool dispatch

Incremental transmission loss analysis has been used for decades, but recent interest in its application to loss allocation calls for new in-depth results. This paper demonstrates that, for incremental methods to be applied correctly in loss allocation, it is first necessary to specify the load distribution and loss supply strategies. Incremental loss allocation among bus power injections is shown to be arbitrary and, therefore, open to challenge as discriminatory. Loss allocation is possible among incremental loads and/or generators, but the proportion of the total losses assigned to either one is arbitrary. Unique, nonarbitrary incremental loss allocations are however possible among the "equivalent" incremental bilateral exchanges between generators and loads. From these basic components it is possible then to calculate the allocation among generators or loads in any specified proportion. The main results, although developed initially for small increments, are extended to large variations. Finally, a general incremental loss allocation algorithm is developed and tested     

Crisis phenomena upon evaporation in grid capillary and porous coatings and arterial structures of heat pipes

The article presents the results of experimental investigations of critical (limit) heat fluxes upon evaporation on porous coatings, and it substantiates the physical model of the process.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 49, No. 4, pp. 607–614, October, 1985.     

The hot blow forming of AZ31 Mg sheet: Formability assessment and application development

The hot blow forming of magnesium sheet offers significant opportunity for forming complex, lightweight parts for automotive applications. This paper characterizes the elevated-temperature formability of AZ31 magnesium sheet materials and the effect of processing conditions on the performance of these materials. In addition, magnesium sheet application development at General Motors Corporation is reviewed.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Fuzzy Learning of Talbot Effect Guides Optimal Mask Design for Proximity Field Nanopatterning Lithography

Processing methods used in photonics and nanotechnology possess many limitations restricting their application areas such as high cost, inability to produce fine details, problems with scalability, and long processing time. Proximity field nanopatterning is a lithography method which surpasses these limitations. By using interference patterns produced by a two-dimensional phase mask, the technique is able to generate a submicron detailed exposure on a millimeter-size slab of light sensitive photopolymer, which is then developed like a photographic plate to reveal three-dimensional interference patterns from the phase mask. While it is possible to use simulations to obtain the interference patterns produced by a phase mask, realizing the mask dimensions necessary for producing a desired interference pattern is analytically challenging due to the intricacies of light interactions involved in producing the final interference pattern. An alternative method is to iteratively optimize the phase mask until the interference patterns obtained converge to the desired pattern. However, depending on the optimization technique used, one either risks a significant probability of failure or requires a prohibitive number of iterations. We argue that an optimization technique that is to take advantage of the physics of the problem using machine learning methods (here fuzzy learning) can lead to competent mask design. This technique is described in this letter.     

Modification of platinum surfaces by spontaneous deposition: Methanol oxidation electrocatalysis

The presence of a second metal on platinum surfaces affects the performance of methanol oxidation. However, most of the electrocatalytic reactions are studied by using electrochemically deposited platinum alloys, but in the case of spontaneous deposition the situation is not so clear since the surface distribution, stability and morphology are usually not well documented. The formation of surface decorated samples on mono- and poly-crystalline platinum is followed by electrochemical and spectroscopic techniques and analysis of their performance towards methanol adsorption and oxidation compared with that on pure platinum. Pt/Sn and Pt/Ru are of special interest because of their well-known performance in methanol fuel cells. Methanol oxidation on Pt(111)/Ru, Pt(111)/Sn and Pt(111) shows that ruthenium is the only one able to promote the reaction since the simultaneous dissolution of tin occurs and competes with the process of interest. The in situ infrared spectroscopy is used to compare methanol oxidation on Pt(111)/Ru and Pt(111) in acid media using p-polarized light. The formation of bridge bound carbon monoxide is inhibited in the presence of ruthenium ad-species, whereas on Pt(111) the three adsorption configurations are observed. Linear sweep polarization curves and Tafel slopes (calculated from steady state potentiostatic plots) for methanol oxidation are compared on polycrystalline surfaces modified by tin or ruthenium at different coverages. There is almost no change in the Tafel slopes due to the presence of the foreign metal except for Pt/Ru, where a 0.09 V decade⁻¹ slope was calculated below 0.55 V due to hydroxyl adsorbates on ruthenium islands. The anodic stripping of methanol residues on the three surfaces indicates a lower amount of carbon monoxide-type adsorbates on Pt/Ru, and the simultaneous tin dissolution process leading to residues oxidation on Pt/Sn electrodes.