Microwave signal generation using an optical self-heterodyne technique

A new technique for mixing optical waves to generate microwave-frequency signals using an injection laser diode and a fibre-optic interferometer is reported. A beat signal is produced by interfering light from the laser with light from the same laser emitted earlier at a different frequency. The interferometer consists of an evanescent-field fibre coupler joined to a length of single-mode optical fibre. The laser is tuned by pulsed or bipolar current waveforms superimposed on a DC bias current. Feedback from an external cavity stabilises the laser frequency and reduces its linewidth. Efficient mixing at difference frequencies from 250 MHz to 2 GHz is obtained, with spectral widths of less than 1% of the centre frequency.     

Pulse-stream VLSI neural networks mixing analog and digitaltechniques

The pulse-stream technique, which represents neural states as sequences of pulses, is reviewed. Several general issues are raised, and generic methods appraised, for pulsed encoding, arithmetic, and intercommunication schemes. Two contrasting synapse designs are presented and compared. The first is based on a fully analog computational form in which the only digital component is the signaling mechanism itself-asynchronous, pulse-rate encoded digital voltage pulses. In this circuit, multiplication occurs in the voltage/current domain. The second design uses more conventional digital memory for weight storage, with synapse circuits based on pulse stretching. Integrated circuits implementing up to 15000 analog, fully programmable synaptic connections are described. A demonstrator project is described in which a small robot localization network is implemented using asynchronous, analog, pulse-stream devices.     

Effects of seat slope and hip flexion on spinal angles in sitting

Lumbar and thoracic spinal angles of 25 male and 25 female subjects were measured in four sitting postures, with standing angles used as reference. Subjects sat with either 90 deg or 65 deg of hip flexion on either flat or forward-sloping seats. Lumbar kyphosis was greatest when the flat seat/90-deg posture was adopted and least when the sloping seat/65-deg posture was adopted. The opposite was observed for the thoracic angles, and intermediate results were observed for the other two sitting postures. No statistically significant interactions were observed among seat slope, hip flexion, and subject sex. The findings are discussed with reference to the anatomy of sitting and factors influencing pelvic tilt and the implications for the ergonomic design of chairs.     

Measurement of the delayed-neutron yields in the fission of233U,236U,237Np,240Pu,and241Pu by neutrons from the spectrum of a fast reactor

Translated from Atomnaya Énergiya, Vol. 66, No. 2, pp. 100–103, February, 1989.     

A mixed finite element model for the elastic contact problem

The static elastic contact problem is approached using Lagrange multipliers, leading to a mixed finite element problem. A non-linear friction law is introduced explicitly and the non-local character of the friction phenomena is implicitly assumed. In order to avoid stress oscillations near singular points, a perturbed Lagrangian functional is considered. The algorithms herein proposed do not impose nodal dependencies over the contact surfaces, allowing for the independent discretization of both bodies. The method is able to model simultaneous contact over different regions of any geometrical shape. Computer code, examples and results presented here are restricted to axisymmetrical and bidimensional cases.     

Failure analysis of aluminum cable steel reinforced (ACSR) conductor of the transmission line crossing the Paraná River

The failure of the conductor of the 460 kV overhead transmission line located along the crossing of the Paraná River was investigated. As a result of this failure, a blackout took place in the southern states of Brazil in January of 2002, reaching approximately 67 million inhabitants. Investigation of the external aluminium layer of the ACSR conductor near the fracture showed typical static deformation marks and dynamic fretting wear tangential marks, both associated with the presence of Al₂O₃ debris. Additionally, encrusted silicon particles were observed on the external surface of the strands. The internal Al layer showed elliptical deformation marks also associated with Al₂O₃ debris. Both Al₂O₃ and Si particles are efficient abrasive material, which associated with slight relative motion of metallic surfaces (clamp/strand and strand/strand) can promote fretting wear. Two types of fracture surface of the Al strands were identified: 45° and quasi-normal surfaces, the former being the predominant type. Delamination and particle detachment were the mechanisms of superficial degradation observed on the Al strands, indicating that the rupture of the strands occurred under a gross slip fretting regime induced by sub-conductor oscillation. Inspection of the internal surface of as-cast Al–10%Si spacer clamps revealed different stages of intense circumferential wear caused by the preferential cracking and particle detachment of the eutectic constituent of the as-cast microstructure. This intense wear reduces the clamping contact pressure, which allows higher displacement amplitude and leads to the critical fretting regime. Finally, a few suggestions are discussed to minimise the occurrence of future failures.     

Magnetic field dependence of shielding current density in Y-Ba-Cu-O rings at 77 K

A method for contactless measurement of the shielding critical current density and its dependence on the external magnetic field is described and analyzed. The obtained values are compared with those measured resistively on two different samples. It is shown that the shielding critical current densityJ _cs and the intergranular transport current densityJ _cr are identical if the measurement conditions are similar. A degradation ofJ _cs measured in the external field with AC ripple has been observed.