Intergranular Oxidation of Nickel-Base Alloys: Potentialities of Focused Ion Beam Tomography

Oxidation of Metals - The present work focuses on the intergranular oxidation of Alloy 600 and its weld material Alloy 82 after exposure in simulated primary water at 340–360 °C...     

Iridium complexes incorporating coumarin moiety as catalyst photoinitiators: Towards household green LED bulb and halogen lamp irradiation

Household LED bulbs and halogen lamps are used to promote the ring-opening photopolymerization of epoxides in the presence of a new series of iridium(III) complexes (IrCs) exhibiting enhanced visible light absorption properties through the introduction of a coumarin moiety. These latter complexes are used as catalyst photoinitiators in an oxidative cycle in combination with a silane and an iodonium salt. Remarkably, even under the selected very soft irradiations (e.g. light intensity lower than 2 mW/cm²), excellent polymerization profiles are obtained (conversions > 80%). The mechanisms are investigated by ESR and luminescence experiments.     

CoopStor: a cooperative reliable and efficient data collection protocol in fault and delay tolerant wireless networks

Wireless Networks - Internet of things consist in the deployment of constrained and battery-powered devices with a radio interface. Most industrial applications require to respect strict...     

Drag Power Loss Investigation in Cylindrical Roller Bearings Using CFD Approach

In high-speed rolling element bearings, the drag forces can be prominent and it is demonstrated in this investigation that the classical models may not be appropriate for correctly estimating this power loss contribution. A modification of the models is thus proposed, including the usual drag forces formulation relying upon the drag coefficient to be evaluated from a numerical computational fluid dynamics (CFD) approach. A three-dimensional approach that considers both the rings and the cylinder ends seems the only adequate approach to be used because a two-dimensional approach predicts a drag coefficient value that is too low. When using the former computed drag coefficient for the evaluation of the total power losses, high values of oil volume fraction must be employed to recover the measured power losses.     

Fast Quadtree/Octree adaptive meshing and re-meshing with linear mixed elements

Engineering with Computers - In this paper, we will focus on adaptive meshing and re-meshing. We present an original approach, based on Quadtree and Octree, to construct the initial mesh and refine...     

Low speed lifting cable diagnosis using instantaneous angular speed

Journal of Mechanical Science and Technology - This paper describes an experimental study of lifting cable fault diagnostic based on instantaneous angular speed (IAS) technique. During the study...     

Bio-derived sodium silicate for the manufacture of alkali-activated binders: Use of bamboo leaf ash as silicate source

Alkali activated binders are a promising alternative to the use of Portland cement in the manufacture of concrete for curbing CO₂ emissions. Novel sources of silicates have been investigated in recent years for reducing cost and environmental impacts associated with the use of chemical activators. This study describes the production of solid sodium silicate (SS) activating powder from bamboo leaf ash (BLA). Bamboo leaves were calcined at 550–800°C, mixed with NaOH pellets, and heated in an oven at 300°C. The obtained silicate powder was used for activating blended fly ash/slag samples. Mechanical and microstructural properties of BLA-based samples were compared to those of samples made with commercially available chemicals. The strength of BLA-activated mortars matched the commercially-sourced activators, being 25–30 MPa at 7 days and exceeding 40 MPa at 28 days. The microstructural analysis suggested that BLA-based SS showed a lesser degree of dissolution of precursors at 7 days, but the quality of the matrix was higher than that of NaOH-activated samples. These results confirmed that the reactivity of BLA-silicate powder was similar to that of commercial SS solutions, and show the potential valorization of future biomass renewable waste in the production of low carbon, alkali-activated concretes.     

Slip Length Measurements Using µPIV and TIRF-Based Velocimetry

The goal of this paper is to review progress (mostly recent) made in micro and nanovelocimetry, focusing on two techniques: µPIV (microparticle image velocimetry) and nanoPTV (nanoparticle tracking velocimetry). The paper focuses on the measurement of slippage (taken as a benchmark for these techniques), concentrating on work done in our group. We review the developments of µPIV that led, in the last ten years, to the achievement of 100 nm accuracy in the measurement of slip lengths. Later, this approach was complemented by nanoPTV, which recently obtained ±5 nm precision. Here, we also mention recent application of these techniques toward better characterization of microgel and polymer flows. As a whole, the two techniques have conveyed valuable information on flow behavior within and close to the boundaries of microchannels, on the importance of wetting, and on the role of surface heterogeneities. µPIV is commercially available but nanoPTV is not mature. Interesting instrumental developments are expected in the future for the latter technique.     

Nickel phosphonate MOF as efficient water splitting photocatalyst

A novel microporous two-dimensional(2D)Ni-based phosphonate metal-organic framework(MOF;denoted as IEF-13)has been successfully synthesized by a simple and green hydrothermal method and fully characterized using a combination of experimental and computational techniques.Structure resolution by single-crystal X-ray diffraction reveals that IEF-13 crystallizes in the triclinic space group Pi having bi-octahedra nickel nodes and a photo/electroactive tritopic phosphonate ligand.Remarkably,this material exhibits coordinatively unsaturated nickel(II)sites,free-P0₃H₂and-P0₃H acidic groups,a C0₂accessible microporosity,and an exceptional thermal and chemical stability.Further,its in-deep optoelectronic characterization evidences a photoresponse suitable for photocatalysis.In this sense,the photocatalytic activity for challenging H₂generation and overall water splitting in absence of any co-catalyst using UV-Vis irradiation and simulated sunlight has been evaluated,constituting the first report for a phosphonate-MOF photocatalyst.IEF-13 is able to produce up to 2,200 fimol of H₂per gram using methanol as sacrificial agent,exhibiting stability,maintaining its crystal structure and allowing its recycling.Even more,170μmol of H₂per gram were produced using IEF-13 as photocatalyst in the absence of any co-catalyst for the overall water splitting,being this reaction limited by the 0₂reduction.The present work opens new avenues for further optimization of the photocatalytic activity in this type of multifunctional materials.