Zr‐Doped Indium Oxide (IZRO) Transparent Electrodes for Perovskite‐Based Tandem Solar Cells

Parasitic absorption in transparent electrodes is one of the main roadblocks to enabling power conversion efficiencies (PCEs) for perovskite‐based tandem solar cells beyond 30%. To reduce such losses and maximize light coupling, the broadband transparency of such electrodes should be improved, especially at the front of the device. Here, the excellent properties of Zr‐doped indium oxide (IZRO) transparent electrodes for such applications, with improved near‐infrared (NIR) response, compared to conventional tin‐doped indium oxide (ITO) electrodes, are shown. Optimized IZRO films feature a very high electron mobility (up to ≈77 cm² V^?1 s^?1), enabling highly infrared transparent films with a very low sheet resistance (≈18 Ω □^?1 for annealed 100 nm films). For devices, this translates in a parasitic absorption of only ≈5% for IZRO within the solar spectrum (250–2500 nm range), to be compared with ≈10% for commercial ITO. Fundamentally, it is found that the high conductivity of annealed IZRO films is directly linked to promoted crystallinity of the indium oxide (In₂O₃) films due to Zr‐doping. Overall, on a four‐terminal perovskite/silicon tandem device level, an absolute 3.5 mA cm^?2 short‐circuit current improvement in silicon bottom cells is obtained by replacing commercial ITO electrodes with IZRO, resulting in improving the PCE from 23.3% to 26.2%.     

Use of basalt in asphalt concrete mixes

One of the main reasons behind the appearance of early distresses in Jordan roads and the low surface skid resistance is the use of marginal quality limestone aggregate. Large quantities of good quality basalt are available in the Northeastern parts of Jordan. In this research, the possibility of improving the properties of local asphalt concrete mixes by replacing different portions of the normally used limestone aggregate by basalt was investigated. The replacement included total replacement of the limestone by basalt, replacing the coarse aggregate, and replacing the fine aggregate. Results showed that the optimal mix was the mix that had basalt coarse aggregate and limestone fine aggregate. In order to overcome the stripping potential of the optimal mix, 20% of the filler portion of the aggregate, material smaller than 0.075 mm, was replaced by lime. The optimal mix showed superiority, over the tested mixes, in all the evaluated properties, which were Marshall Stability, indirect tensile strength, stripping resistance, resilient modulus, dynamic creep, fatigue, and rutting.     

Enabling machine understandable exchange of energy consumption information in intelligent domotic environments

In the 21st century, all the major countries around the world are coming together to reduce the impact of energy generation and consumption on the global environment. Energy conservation and its efficient usage has become a top agenda on the desks of many governments. In the last decade, the drive to make homes automated and to deliver a better assisted living picked pace and the research into home automation systems accelerated, usually based on a centralized residential gateway. However most devised solutions fail to provide users with information about power consumption of different house appliances. The ability to collect power consumption information can lead us to have a more energy efficient society. The goal addressed in this paper is to enable residential gateways to provide the energy consumption information, in a machine understandable format, to support third party applications and services. To reach this goal, we propose a Semantic Energy Information Publishing Framework. The proposed framework publishes, for different appliances in the house, their power consumption information and other properties, in a machine understandable format. Appliance properties are exposed according to the existing semantic modeling supported by residential gateways, while instantaneous power consumption is modeled through a new modular Energy Profile ontology.     

Use of low CaO unprocessed steel slag in concrete as fine aggregate

Steel slag, which is produced locally in great amounts, has a negative impact on the environment when disposed. Local steel slag has a low CaO content and has no pozzolanic activity.In this research, local unprocessed steel slag is introduced in concrete mixes. Various mixes with compressive strength ranging from 25 to 45 MPa are studied. The slag is used as fine aggregate replacing the sand in the mixes, partly or totally. Ratios of 0%, 15%, 30%, 50% and 100% are used.Depending on the grade of concrete, the compressive strength is improved when steel slag is used for low sand replacement ratios (up to 30%).When optimum values are used, the 28-day tensile strength of concrete is improved by 1.4–2.4 times and the compressive strength is improved by 1.1–1.3 times depending on the replacement ratio and the grade of concrete. The best results are obtained for replacement ratios of 30–50% for tensile strength and 15–30% for compressive strength.Therefore, the use of steel slag in concrete would enhance the strength of concrete, especially tensile strength, provided the correct ratio is used.     

Design,characterization and implementation of a fiber Bragg grating temperature sensor for application in solar power electronic inverters

This paper reports the design, characterization and implementation of a fiber Bragg grating (FBG) temperature sensor in a power electronic inverter which has a high electromagnetic interference (EMI) radiation. The performance and characteristics of the sensor are investigated by monitoring the temperature variation of the insulated gate bipolar transistor (IGBT) in photovoltaic (PV) arrays inverter. The thermal expansion of the optical fiber is enhanced by mounting the FBG sensor to a metal sheet. Due to this enhancement, the FBG temperature sensor recorded an improvement in terms of linearity and sensitivity. A comparison is made between the performance of the enhanced FBG sensor and a thermocouple in a high EMI environment, and the results show that the FBG sensor performs better.     

Scalable Parallel Algorithms for FPT Problems

Algorithmic methods based on the theory of fixed-parameter tractability are combined with powerful computational platforms to launch systematic attacks on combinatorial problems of significance. As a case study, optimal solutions to very large instances of the NP-hard vertex cover problem are computed. To accomplish this, an efficient sequential algorithm and various forms of parallel algorithms are devised, implemented, and compared. The importance of maintaining a balanced decomposition of the search space is shown to be critical to achieving scalability. Target problems need only be amenable to reduction and decomposition. Applications in high throughput computational biology are also discussed.     

Linking learning goals and educational resources through interactive concept map visualizations

Concept browsing interfaces can help educators and learners to locate and use learning resources that are aligned with recognized learning goals. The Strand Map Service enables users to navigate interactive visualizations of related learning goals and to request digital library resources aligned with learning goals. These interfaces are created using a programmatic Web service interface that dynamically generates interactive visual components. Preliminary findings suggest that these library interfaces appear to help users stay focused on the scientific content of their information discovery task, as opposed to focusing on the mechanics of searching.     

Contractors’ Views of the Potential Causes of Inconsistencies between Design and Construction in Saudi Arabia

The study identifies the causes of inconsistencies between the design and construction of large building projects. To achieve the study objectives, a questionnaire survey was carried out to collect information on potential causes of inconsistencies at the project design and construction interface. Responses from 27 contractors were analyzed. The results suggest that the involvement of designer as consultant, communication gap between constructor and designer, insufficient working drawing details, lack of coordination between parties, lack of human resources in design firm, lack of designer’s knowledge of available materials and equipment, and incomplete plans and specifications were considered as the most important causes of the project design and construction interface inconsistencies. On the other hand, project management as a professional service, weather conditions, nationalities of participants, involvement of the contractor in design conceptual phase, unforeseen problems, involvement of the contractor in design development phase, and government regulations were the least important causes of inconsistencies between professionals at the project design and construction interface in large building projects.