Phase development and pore stability of yttria- and ytterbia-stabilized zirconia aerogels

High-porosity yttria- and ytterbia-stabilized zirconia aerogels offer the potential of extremely low thermal conductivity materials for high-temperature applications. Yttria- and ytterbia-doped zirconia aerogels were synthesized using a sol-gel approach over the dopant range of 0-20 atomic percent. Surface area, pore volume, and morphology of the as-dried aerogels and materials thermally exposed for short periods of time to temperatures up to 1200°C were characterized by nitrogen physisorption, scanning and transmission electron microscopy, and X-ray diffraction. The aerogels as supercritically dried all were X-ray amorphous. At a 5% dopant level, a tetragonal structure with a smaller monoclinic phase developed on thermal exposure. Mixed tetragonal and cubic phases or predominantly cubic materials were observed at higher dopant levels, depending on the dopant level, temperature and exposure time. The formation of crystalline phases was accompanied by loss of surface area and pore volume, although some mesoporous structure was maintained on short-term exposure to 1000°C. Incorporation of the smaller Yb atom into the lattice structure resulted in smaller lattice dimensions on crystallization than was seen with Y doping and favored a more highly equiaxed structure. Aerogels synthesized with 15% Y maintained the smallest particle size without evidence of sintering at 1100°C. Largest shrinkage and loss of pore volume occurred on crystallization from the amorphous phase, with further loss of pores at temperatures above 1000°C attributable to changes in lattice parameters.     

Off-axis tensile properties and fracture in a unidirectional graphite/polyimide composite (celion 6000/PMR 15)

Tensile properties of unidirectional Celion 6000 graphite/PMR 15 polyimide composites prepared by hot molding and cold molding processes were measured at room temperature and 316°C, the upper use temperature of the polyimide resin, at both 45 and 90° to the fiber axis. The resulting fractures were characterized by scanning electron microscopy and materialographic techniques. Variation in tensile properties with processing history occurred in the elastic modulus and strain to failure for specimens loaded at 90° at 316°C, and in the fracture stress, and hence the in-plane shear stress, for those loaded at 45° at room temperature. Significant plastic deformation was observed in the 45° orientation at 316°C for material produced by both processing methods. In general, fracture occurred by both failure within the matrix and at the fiber-matrix interface; the degree of interfacial failure increased with temperature. Secondary cracking below the primary fracture surface also was observed.     

Forced torsional properties of PMR composites with varying nadic ester concentrations and processing histories

PMR polyimide resin was prepared from 4,4′-methylenedianiline (MDA), the dimethyl ester of 3,3′,4,4′- benzophenonetetracarboxylic acid (BTDE) and the monomethyl ester of 5-norbornene-2,3-dicarboxylic acid (NE). The NE group serves as a chain terminator and crosslinking site. PMR/Celion 6000 composites were fabricated from resins having varying NE concentrations using two molding processes, and the laminates characterized in forced torsion. Glass transition temperatures (T_g) of 360–390°C were observed in the crosslinked resins, as compared with the literature value of 284°C reported for the uncrosslinked systemT_g did not decrease with decreasing NE concentrations over the range from 2.0 to 1.25 moles. Stoichiometry, within the range studied, showed little influence on shear properties; however, a 25% variation in matrix shear modulus with processing was observed. The G₁₂ values determined in forced torsion were in excellent agreement with those reported from tensile tests of ±45° laminates. A branching and possible secondary crosslink mechanism is proposed based on dynamic mechanical behavior and infrared spectra of the composites.     

Changes in blubber contaminant concentrations in California sea lions (Zalophus californianus) associated with weight loss and gain during rehabilitation

California sea lions have high levels of persistent organic pollutants (POPs) in their blubber. Animals affected by domoic acid fast and refeed during their rehabilitation. We studied the effect of decreases in total body mass (16 +/- 7% of initial body mass) on blubber POP contaminant concentrations and estimated POP burdens during fasting (12 +/- 5 days) in 19 California sea lions. The effect of refeeding (92 +/- 8% of initial body mass) was also investigated. Significant increases in the concentration of all POPs were found over the mass loss period and decreases during mass gain. A basic mass balance model indicated that the changes did not conform to a simple concentrating and diluting pattern and a proportion of the contaminants were lost from the lipid pool. During mass loss, the lower chlorinated polychlorinated biphenyl congeners, chlordanes, and hexachlorocyclohexanes were lost at a higher rate than the other contaminant classes (particularly polybrominated diphenyl ethers). During mass gain the behavior of all contaminant classes was more consistent with the dilution model. These results indicate the importance of considering the energetic contextwhen sampling blubberfor long-term contaminant monitoring and suggest an initial approach to adjust for such differences.     

Sex- and Genotype-Dependent Nicotine-Induced Behaviors in Adolescent Rats with a Human Polymorphism (rs2304297) in the 3′-UTR of the CHRNA6 Gene

In human adolescents, a single nucleotide polymorphism (SNP), rs2304297, in the 3′-UTR of the nicotinic receptor subunit gene, CHRNA6, has been associated with increased smoking. To study the effects of the human CHRNA6 3′-UTR SNP, our lab generated knock-in rodent lines with either C or G SNP alleles. The objective of this study was to determine if the CHRNA6 3′-UTR SNP is functional in the knock-in rat lines. We hypothesized that the human CHRNA6 3′-UTR SNP knock-in does not impact baseline but enhances nicotine-induced behaviors. For baseline behaviors, rats underwent food self-administration at escalating schedules of reinforcement followed by a locomotor assay and a series of anxiety tests (postnatal day (PN) 25-39). In separate cohorts, adolescent rats underwent 1- or 4-day nicotine pretreatment (2×, 30 μg/kg/0.1 mL, i.v.). After the last nicotine injection (PN 31), animals were assessed behaviorally in an open-field chamber, and brain tissue was collected. We show the human CHRNA6 3′-UTR SNP knock-in does not affect food reinforcement, locomotor activity, or anxiety. Further, 4-day, but not 1-day, nicotine exposure enhances locomotion and anxiolytic behavior in a genotype- and sex-specific manner. These findings demonstrate that the human CHRNA6 3′-UTR SNP is functional in our in vivo model.     

W-Hierarchies Defined by Symmetric Gates

The classes of the W-hierarchy are the most important classes of intractable problems in parameterized complexity. These classes were originally defined via the weighted satisfiability problem for Boolean circuits. Here, besides the Boolean connectives we consider connectives such as majority, not-all-equal, and unique. For example, a gate labelled by the majority connective outputs true if more than half of its inputs are true. For any finite set C\mathcal{C} of connectives we construct the corresponding W( C\mathcal{C} )-hierarchy. We derive some general conditions which guarantee that the W-hierarchy and the W( C\mathcal{C} )-hierarchy coincide levelwise. If C\mathcal{C} only contains the majority connective then the first levels of the hierarchies coincide. We use this to show that a variant of the parameterized vertex cover problem, the majority vertex cover problem, is W[1]-complete.