Colloidal silica removal in coagulation processes for wastewater reuse in a high-tech industrial park.

Four experiments of coagulation and flocculation were conducted to investigate the characteristics of colloidal silica removal in a high-tech industrial wastewater treatment plant for reclamation and reuse of the effluent. Experimental results illustrated that poly-aluminium chloride (PACl) showed higher performances on colloidal silica removal than alum. Interestingly, the two coagulants demonstrated the same capacity on silica removal. The specific silica removal capacity was approximately 0.135 mg SiO2/mg Al2O3 when the dosage of coagulants was in the range 30-150 mg/L Al2O3. In addition, the silica was reduced significantly at the condition of pH above 8. Experimental data implied that precipitation of aluminium flocs was the major mechanism for colloid silica removal in PACl and alum coagulation, besides, charge adsorption was also important for improving removal efficiency. Moreover, the addition of polyacrylic acid (PAA) as a flocculant could slightly advance silica removal in the PACl coagulation. The combined PACl/PAA/flocs coagulation was effective for the removal of colloidal silica, soluble COD, and turbidity and also suitable as a pretreatment unit in wastewater reclamation and reuse processes.     

Mössbauer spectroscopic studies of Fe-substituted YIG

Compositional dependence of hyperfine parameters, determined through Mössbauer spectral analysis has been studied for Y_3−xFe_5+xO₁₂ (x = 0.0, 0.1, 0.3 and 0.5) garnet system at 300 K. The Mössbauer spectra have been fitted with three sextets in the ferrimagnetic state corresponding to Fe³⁺ ions at tetrahedral (d), octahedral (a) and dodecahedral (c) sites of the crystal structure. It is observed that isormershift, quadrupole shift and hyperfine field of d-site show no significant variation with Fe³⁺ concentration. The change in hyperfine fields of a- and c-sites with composition (x) has been explained on the basis of strength of exchange integrals, change in isomershift can be understood due to s-electron charge distribution and asymmetric displacement of oxygen ions surrounding the a- and c-sites seems to be responsible for observable quadrupole shift. The magneton number values obtained from magnetization and Mossbauer data are in agreement to those calculated using Neel's three sublattice model of ferrimagnetism.     

Investigation of the geothermal anomaly of Travale (Tuscany) by telluric, magnetotelluric and geomagnetic deep sounding measurements

As part of the European Community research programme telluric, magnetotelluric and geomagnetic deep sounding measurements were undertaken at 40 sites within the geothermal area of Travale. In the period range of 6–10,000 s the telluric field inside the Travale graben is strongly polarized and directed, independent of the period, about parallel to the graben strike. The lateral variation of the telluric field amplitude is determined mainly by the distribution of the rocks (e.g. the central part of the geothermal anomaly inside the graben is correlated with a horst structure of resistive rocks) and an influence of the geothermal anomaly on the telluric field distribution cannot be observed. The apparent resistivity, as well as the phase curves, are rather similar at all sites within the graben, exhibiting 4–40 ohm · m for periods of 10 s and 50–500 ohm · m for periods of 10,000 s in E-polarization. In the period range of 10–100 s the E- and B-polarization of magnetotelluric measurements can be interpreted by the 2-D effect of the Travale graben, while with increasing period the induced current system becomes more and more 3-D below all sites. This limits the determination of the sedimentary cover thickness (max. 2500 m) by 1-D and 2-D model calculations to periods of less than 100 s.     

Integrated-optic device for a fibre laser Doppler velocimeter

We first demonstrate an integrated-optic device for a fibre laser Doppler velocimeter, which consists of a waveguide interferometer and a frequency shifter in z-propagation Ti-diffused LiNbO3. The device is also pigtailed with a single-mode fibre to pick up a Doppler-shifted signal. Using the fabricated device, the velocity of a moving object was successfully heterodyne-detected with a signal/noise ratio of 30dB.     

A Graphene Field-Effect Device

In this letter, a top-gated field-effect device (FED) manufactured from monolayer graphene is investigated. Except for graphene deposition, a conventional top-down CMOS-compatible process flow is applied. Carrier mobilities in graphene pseudo-MOS structures are compared to those obtained from the top-gated Graphene-FEDs. The extracted values exceed the universal mobility of silicon and silicon-on-insulator MOSFETs     

Sensitivity analysis of the scattering parameters of microwave filters using the adjoint network method

A novel approach is presented to calculate the sensitivities of the scattering parameters of microwave filters obtained with the full‐wave mode‐matching (MM) technique. Using only the MM simulation of the original network, the sensitivities of the scattering parameters with respect to all designable parameters are obtained. The adjoint network method (ANM) is applied to the generalized scattering matrices of the different filter components. This guarantees good accuracy of the calculated sensitivities. The implementation details are discussed for N‐resonator ridge waveguide filters. Excellent agreement is obtained between the sensitivities calculated using ANM and those obtained using the expensive central differences. © 2006 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2006.     

On the behavior of microstructures with multiple length scales

The current study aims to provide fundamental insight into the behavior of microstructures containing grain sizes that span multiple length scales. A commercial 5083 Al alloy was selected as the material of interest to facilitate comparison with recently published data. The materials studied here were prepared via the thermal consolidation of powders that were cryomilled for different times (i.e., 0, 2, 4, and 8 hours). Following consolidation, the resultant microstructure was characterized by an equiaxed grain morphology with a size distribution centered around 200∼300 nm. Dispersed among the 200- to 300-nm grains were coarse-grained regions or ligaments with a grain size ranging from 600 nm to 2 μm. The occurrence of coarse-grained regions is rationalized on the basis of recrystallization or subgrain coarsening, whereas the occurrence of equiaxed fine regions is proposed to be a result of continuous grain growth. Two types of microstructures were selected for study, containing coarse-grained volumes of approximately 28 pct and 43 pct that corresponded to an ultimate tensile strength (UTS) of 566 MPa and 535 MPa, and a fracture strain of 3.2 pct and 3.5 pct, respectively. The observed ductility and the relevant toughening mechanisms were discussed in light of the presence of multiple length scales.     

A risk approach to the management of boiler tube thinning

A large set of industrial thickness inspection data covering four boiler units of a power station over a period of five years was made available to the authors. The measurements were made in regions of the boiler where corrosion/erosion was the major cause of failure of the boiler tubes. There were over 40,000 separately measured data points in the data and all were collected with some care and expense.In the development of maintenance strategies for equipment, this type of data is typical of the data that must be collected and assessed. This data thus represents an opportunity to evaluate the ability to generate a useful risk approach to the management of the tubing.An important example of a risk-based approach is the American Petroleum Institute (API) Risk Based Inspection (“RBI”), API 581. A variety of problems were encountered applying this to boiler tubes. The problems include irrelevant API 581 corrosion rate tables, lack of information on how to analyse inspection data, difficulty of dealing with multiple inspection categories and lack of suitable direction for programming inspection intervals.     

Modeling the tensile properties in β-processed α/β Ti alloys

The development of a set of computational tools that permit microstructurally based predictions for the tensile properties of commercially important titanium alloys, such as Ti-6Al-4V, is a valuable step toward the accelerated maturation of materials. This paper will discuss the development of neural network models based on a Bayesian framework to predict the yield and ultimate tensile strengths of Ti-6Al-4V at room temperature. The development of such rules-based model requires the population of extensive databases, which in the present case are microstructurally based. The steps involved in database development include producing controlled variations of the microstructure using novel approaches to heat treatments, the use of standardized stereology protocols to characterize and quantify microstructural features rapidly, and mechanical testing of the heat-treated specimens. These databases have been used to train and test neural network models for prediction of tensile properties. In addition, these models have been used to identify the influence of individual microstructural features on the tensile properties, consequently guiding the efforts toward development of more robust mechanistically based models. Based on the neural network model, it is possible to investigate the influence of individual microstructural features on the tensile properties, and in certain cases these dependencies can point toward unrecognized phenomena. For example, the apparently unexpected trend of increase in tensile strength with increasing prior β-grain size has led to the determination of the pronounced role of the basketweave microstructure in strengthening these alloys, especially in case of larger prior β grains. This article is based on a presentation made in the symposium “Computational Aspects of Mechanical Properties of Materials,” which occurred at the 2005 TMS Annual Meeting, February 13–17, 2005, in San Francisco, CA, under the auspices of the MPMD-Computational Materials Science & Engineering (Jt. ASM-MSCTS) Committee.     

Poly-functional Catalyst Development for Benzene Production from Alkyl-aromatic Mixture via Hydrodealkylation

Development of a poly-functional catalyst that has higher hydrodealkylation activity based on 15% Cr/γ- Al₂ O₃ was researched for benzene production from an alkyl-aromatic mixture via hydrodealkylation. For this goal, the effects of the promoters like Fe, Co, or Ni and their concentrations on the activity of a Cr/Al₂ O₃ catalyst were investigated. Toluene + n-heptane + tetrahydrotiophene (89:10:1 w%) model mixture, which has the same content as industrial aromatics, was used as feedstock. The activities of catalysis in reactions of hydrodealkylation, hydrocracking, and hydrogenolize with respect to conversions of toluene, heptane, and tetrahydrotiophene were tested, respectively. As to the obtained results, the catalyst including 5% Fe has a higher hydrodealkylation activity, compared to the catalyst including Co, and especially to the alumocrom catalyst not including a promoter, while it has a lower coke formation and reduced activity to the catalyst including Ni.