Thermal conductivity analysis using three‐dimensional microstructures of gelation freezing derived cellular mullite

The relationship between thermal conductivity and unidirectional cellular mullite microstructures created with the freeze casting route is discussed using actual three‐dimensional (3D) images, in which a homogenization method was conducted with microscopic models created from 3D images, the temperature variation in macroscopic models by the finite element method (FEM), and local heat conduction in microscopic models. The simulation results were consistent with the experimental results. This image‐based modeling technique was thus confirmed to be a strong tool for the prediction of various thermal properties of porous ceramics.     

Tensile Test Specimens with a Circumferential Precrack for Evaluation of Interfacial Toughness of Thermal-Sprayed Coatings

A new testing procedure to evaluate the interfacial toughness of thermal-sprayed coatings has been developed. The newly designed test specimen is a modification of the pin test with an artificially introduced weak interface, which is expected to open up easily under tensile loading and act as a circumferential precrack along the interface between a coating and the substrate. This configuration makes it possible to calculate the stress intensity factor K _Int at the tip of the precrack, which can be expressed as , where σ₀ is the apparent average stress, a the crack length, R the specimen radius, and F _I the geometrical correction function. Finite-element analysis was carried out to calculate the correction function F _I for various values of a/R. In the experiments, the flat surface of a pin was grit-blasted and a ring-shaped area from the periphery was covered with carbon using a pencil and set into a mating dice. SUS316L stainless steel was plasma-sprayed onto the flat surface of the pin and the dice. Then, tensile load was applied to the pin to break the weak interface containing the carbon and finally the unmodified coating-substrate interface. The load required to pull out the pin was measured for various specimen parameters such as a and R. The results indicate that the adhesion of the tested coatings can be represented by interface toughness of 1.9 ± 0.1 MPa m^1/2. As a consequence, this testing procedure can be considered as a viable method to evaluate adhesion of a thermal-sprayed coating on a substrate.     

New Approach for Macro Porous RB‐SiC Derived from SiC/Novolac‐type Phenolic Composite

A novel fabrication route to make macroporous silicon carbide (SiC) has been proposed in this study. The route is composed of the following two steps: the fabrication of porous α‐SiC/novolac‐type phenolic composite using hexamethylenetetramine (HMT) as a curing/blowing agent for the novolac monomer and a conventional reaction‐bonded (RB) sintering of the composite. The α‐SiC/novolac‐type phenolic composite was carbonized at 800°C for 2 h in N₂ gas and then reacted with the molten silicon at 1450°C for 30 min under vacuum, resulting in the macroporous RB‐SiC with an open porosity of 48% and relatively large pore size of ~110 μm. The compressive strength of the macroporous RB‐SiC was 113 MPa, which is relatively high compared to those reported for macroporous SiC of equivalent porosities and pore sizes.     

Potato and soy peptides alter caecal fermentation and reduce serum non‐HDL cholesterol in rats fed cholesterol

We examined the effect of potato peptides (PPC) in rats fed a cholesterol‐enriched diet, in comparison with two cholesterol‐enriched diets containing soy peptides (SPC) or casein (CNC), and a cholesterol‐free diet containing casein (CN) for 4 weeks. The serum non‐high‐density lipoprotein (HDL) cholesterol level was lower in the PPC‐ (–18.39%) and SPC‐fed (–32.76%) groups (p <0.05) than in the CNC‐fed group at the end of the feeding period. The low‐density lipoprotein receptor mRNA level in the PPC‐fed group, and cholesterol 7α‐hydroxylase and scavenger receptor class B type 1 mRNA levels in the SPC‐fed group, were higher (p <0.05) than in the CN‐ and CNC‐fed groups. Faecal neutral sterol and caecal short‐chain fatty acid concentrations in the PPC‐ and SPC‐fed groups were higher (p <0.05) than in the CN‐ and CNC‐fed groups. The faecal total acidic sterol concentration was higher in the SPC‐fed group than in the CN‐ and PPC‐fed groups. Caecal anaerobe and Bifidobacterium populations were higher (p <0.05) in the PPC‐ and SPC‐fed groups than in the CN‐fed group. This study suggests that potato peptides, as soy peptides, alter caecal fermentation and steroid absorption and reduce the serum non‐HDL cholesterol level in rats fed cholesterol.     

Degradation pathways of pentachlorophenol by photo-Fenton systems in the presence of iron(III), humic acid, and hydrogen peroxide

The degradation characteristics and pathways of pentachlorophenol (PCP) by the photo-Fenton systems were studied in H2O2 aqueous solutions, which contained Fe(III) only [H2O2/Fe(III) system] and Fe(III) + humic acid (HA) [H2O2/Fe(III)/HA system] at pH 5.0. Although 40% of the PCP was degraded after 5 h of irradiation in the H2O2/Fe(III) system, more than 90% was degraded in the H2O2/Fe(III)/HA system. This shows that at pH 5.0 the degradation of PCP is clearly enhanced by the presence of HA in the photo-Fenton system. In the H2O2/Fe(III) system, the production of octachlorodibenzo-p-dioxin (OCDD) was detected, and 2-hydroxy nonachlorodiphenyl ether was also identified as a precursor of OCDD. However, no OCDD production was observed in the H2O2/Fe(III)/HA system. This indicates that the presence of HA represses the production of OCDD during the degradation of PCP by the photo-Fenton system. Such an effect by HA can be attributed to a reaction sequence wherein reaction intermediates derived from PCP, such as PCP., are incorporated into HA. This was verified by 13C NMR and pyrolysis-GC/MS studies.     

A Two‐Stage Stochastic Mixed‐Integer Programming Approach to the Smart House Scheduling Problem

A “smart house” is a highly energy‐optimized house equipped with photovoltaic (PV) systems, electric battery systems, fuel cell (FC) cogeneration systems, electric vehicles (EVs), and so on. Smart houses are attracting much attention recently because of their enhanced ability to save energy by making full use of renewable energy and by achieving power grid stability despite an increased power draw for installed PV systems. Yet running a smart house's power system, with its multiple power sources and power storages, is no simple task. In this paper, we consider the problem of power scheduling for a smart house with a PV system, an FC cogeneration system, and an EV. We formulate the problem as a mixed‐integer programming problem, and then extend it to a stochastic programming problem involving recourse costs to cope with uncertain electricity demand, heat demand, and PV power generation. Using our method, we seek to achieve the optimal power schedule running at the minimum expected operation cost. We present some results of numerical experiments with data on real‐life demands and PV power generation to show the effectiveness of our method. © 2013 Wiley Periodicals, Inc. Electr Eng Jpn, 186(4): 48–58, 2014; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.22336     

First nuclear transmutation of 237Np and 241Am by accelerator-driven system at Kyoto University Critical Assembly

This study demonstrates, for the first time, the principle of nuclear transmutation of minor actinide (MA) by the accelerator-driven system (ADS) through the injection of high-energy neutrons into the subcritical core at the Kyoto University Critical Assembly. The main objective of the experiments is to confirm fission reactions of neptunium-237 (²³⁷Np) and americium-241 (²⁴¹Am), and capture reactions of ²³⁷Np. Subcritical irradiation of ²³⁷Np and ²⁴¹Am foils is conducted in a hard spectrum core with the use of the back-to-back fission chamber that obtains simultaneously two signals from specially installed test (²³⁷Np or ²⁴¹Am) and reference (uranium-235) foils. The first nuclear transmutation of ²³⁷Np and ²⁴¹Am by ADS soundly implemented by combining the subcritical core and the 100 MeV proton accelerator, and the use of a lead-bismuth target, is conclusively demonstrated through the experimental results of fission and capture reaction events.     

Magnetization measurement of 3He film adsorbed on sintered silver powder

The static magnetization of ³He film adsorbed on sintered silver powder has been measured for coverages from 0.10 to 0.54 atoms/»² in steps of 0.02 atoms/»² and at a coverage of 4.5 atoms/»². Below 0.20 atoms/»² the magnetization well obeys the Curie law, while above that coverage a ferromagnetic tendency appears. The coverage dependence of the magnetization greatly differs from that for graphite. At 0.23 atoms/»² the magnetization has apeak like that for graphite; however, the magnitude of the peak is not so large. Furthermore, a multipeak structure is found in the isotherm of the magnetization at 0.2 mK. It has two prominent peaks at 0.23 and 0.29 atoms/»², and two other peaks are found at 0.35 and 0.41 atoms/»². These appear periodically with an interval of 0.06 atoms/»², which is nearly equal to the coverage of one liquid layer.     

Loss factors of mirrors for a gravitational wave antenna

Low-loss mirrors fabricated by ion-beam-sputtering machines for possible application in an interferometric gravitational wave antenna were evaluated by use of Nd:YAG laser light (lambda = 1064 nm) with two distinct measurements: a tabletop experiment that used a short cavity with a small beam with a beam waist of approximately 2w(0) = 0.82 mm, and an optical test that used a 20-m prototypical gravitational-wave detector with a large beam with a beam waist of approximately 2w(0) = 4.4 mm. A multilayer coating comprised 29 layers of SiO(2)/Ta(2)O(5) and one protective coating of SiO(2). The best values obtained as a result of these measurements were 16 ppm (parts in 10(6)) and 30 ppm in total loss, respectively. Also, a two-dimensional loss map generated by use of a small beam successfully revealed the existence of a loss structure within the coating surface. These results imply that a high-reflectance multilayer coating has some inhomogeneities and a loss distribution with a typical scale of a few millimeters and that the total measured losses depend on the beam spot size.     

Wideband and high-power compressively strained GaInAsP/InPmultiple-quantum-well ridge waveguide lasers emitting at 1.3 μm

Compressively strained 1.3-μm GaInAsP/InP multiple-quantum-well (MQW) ridge waveguide lasers were fabricated. Through optimizing the total well thickness, large bandwidth over 11 GHz was achieved, together with high quantum efficiency of about 0.48 W/A and high power output of 60 mW before rollover. The laser also showed less temperature sensitivity up to an elevated temperature of 85°C