External heat transfer in infiltrated granular beds. Experimental study

Experimental data was obtained on external heat transfer in infiltrated granular beds of coarse particles. It was determined that calcualtions with the proposed model agree satisfactorily with the experimental results.Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 53, No. 6, pp. 919–923, December, 1988.     

Heat transfer at the base of a cylindrical cavity oriented perpendicular to a freestream flow

The average and local heat transfer at the base surface of a cylindrical cavity whose opening is perpendicular to an oncoming freestream have been determined experimentally. During the course of the experiments, the cavity depth was varied from zero to 65% of the diameter, while the freestream Reynolds number ranged between about 5000 and 50,000. The average heat transfer coefficient decreased sharply with increasing cavity depth, the reduction being slightly greater than 50% at a depth-diameter ratio of 0.10 and greater than 90% when the depth-diameter ratio was 0.65. For the finite-depth cavities, the local heat transfer coefficient attained its maximum value at the center of the base surface and decreased with increasing radial distance from the center until a minimum was reached, after which there was a moderate increase adjacent to the outer edge of the base. The minimum occurred at the location where the radial outflow along the base separated from the surface, and a toroidal-shaped recirculation zone occupied the corner region at the intersection of the cavity base and side wall. In contrast, for the zero-depth cavity (i.e. a free disk oriented perpendicular to the oncoming flow), the local coefficient attained its minimum at the center of the surface and increased with increasing radial distance from the center.     

A dynamic linear programming approach to market allocation of renewable resources in the italian energy system: The case of solar thermal and biogas technologies

In Italy solar thermal energy and energy from biogas are two possible means of reducing dependence on energy imports. Using a multiperiod LP model (MARKAL) the authors assessed the likely potential of both technologies under various circumstances. The study covered the period 1980–2005, in five segments of five years. It focused only on the subsystem of the energy end-uses which can be substituted for by solar thermal and biogas technologies. The overall non-renewable sources which can be saved in 20 years by these technologies total 450 PJ (1 PJ = 10^{1 5} J) if the fuel prices rise at 0 per cent average annual, 1450 PJ if the fuel prices rise at 4.2 per cent average annual, 1860 PJ if the fuel prices rise at 7.2 per cent average annual and 3780 PJ if the fuel prices rise at 15 per cent average annual. However the most competitive technologies appear to be solar water heaters used mainly in the private and commercial sectors and biogas systems used mainly in the agricultural sector. The study was carried out by APRE under ENEA (formerly CNEN) contract and was intended to serve as an analytical basis for establishing an overall development and demonstration strategy for end-use renewable technologies in Italy.     

From practical methods to theoretical foundations

The year 2006 marks the ninetieth anniversary of the air navigation (later called navigation) service of the Air Forces of this country. The history of air navigation is investigated, and an opinion about its modern state and directions of further development is presented.     

Characterization of an ASIC for CPG sensors with grid-only depth of interaction sensing

A new version of the front-end application specific integrated circuit (ASIC) for co-planar-grid (CPG) sensors is presented. Compared to the first version, the ASIC is optimized for signal/noise performance, modified in peaking time, and it implements timing signals to measure the depth of interaction using the grids signals only. Experimental results using state-of the-art CPG sensors and different approaches for reducing the error due to electron trapping are reported. A new technique that makes use of the sum and difference of the grids signals is also presented.     

Microprocessor testability

As the level of microprocessor complexity increases to several hundred thousand transistors for a single-chip machine, it is becoming very difficult to test commercially available designs to the level of fault coverage desired by some customers. In order to achieve near 100-percent coverage of single stuck-at faults, future microprocessors must be designed with special testing features (designed for testability). The authors describe the testing problem for microprocessors, including the various methods of generating test sets and their application by the user. A survey of the testability features of some of today's commercially available microprocessors is presented. Suggestions for testability features for future-generation microprocessors are also discussed