Interface stability during displacement reactions between Cu<Subscript>2</Subscript>O and Co<Subscript>1−<Emphasis Type="Italic">X</Emphasis></Subscript>Fe<Subscript><Emphasis Type="Italic">X</Emphasis></Subscript> alloys at 1223 K

The stability of the reactive interface during the solid-state displacement reaction, Cu₂O+Co_1−X Fe _X =2Cu+(Co_1−X Fe _X )O, is studied as a function of Co-Fe alloy composition at 1223 K. For X≤0.03, the reaction zone has a layered structure, and the cation diffusion in (Co, Fe)O is the rate-limiting step. The interface is unstable in the early stages of the reaction; the instability decreases with time as the oxide thickness increases, and the interface becomes planar at long times. The time required for the attainment of interface planarity increases with the value of X. The reaction kinetics are consistent with the available cation-diffusion data in (Co, Fe)O. For X≥0.045, the product zone is a composite of Cu+(Co, Fe)O, and the rate is limited by the oxygen transport in copper. The transition to interface instability occurs when the oxide can support a cation flux that exceeds the maximum possible oxygen flux in copper. During the reaction, composition gradients develop in (Co, Fe)O because of higher diffusion rates for iron than for cobalt.     

用于千兆以太网基带铜缆接收器均衡的甚高频自适应 连续时间Gm-C 二阶带通滤波器的研究和设计

本文设计了用于千兆以太网基带铜缆接收器均衡的甚高频自适应连续时间Gm-C二阶带通滤波器。基于最陡梯度下降算法，带通滤波器的零点在57－340MHz的频率范围内可以自适应地调节，中心频率为1.278GHz。通过外接电阻伺服环路，滤波器中跨导转换器的跨导值不受工艺偏差和温度变化的影响，采用CSMC－HJ0.6μm CMOS工艺器件模型，用Cadence Spectres仿真器仿真了设计的自适应滤波器电路，仿真结果验证了设计原理和设计的电路。系统的最长学习时间为880个参考时钟周期。     

On the development of a direct method of determining the microcrack resistance curve

This report deals with direct observations of microcrack linkage at the crack tip prior to macroscopic crack initiation. It is shown that this process is directly linked to the inclusion distribution in the material and can be considered in terms of an R curve to describe microcrack development.     

The contact of elastic regular wavy surfaces

A complete solution in closed form to the elastic contact of a one-dimensional sinusoidal surface with a flat surface was presented by Westergaard in 1939. This paper is concerned with the elastic contact of a two-dimensional sinusoidal surface with a flat. In this case the stress distribution within the elastic solids is three-dimensional. As the load is increased the contact areas change in shape from being circular to square and finally leave a circular region of no contact when the waves are almost squashed flat. The problem is solved in general using a numerical method due to Kalker, but asymptotic solutions in closed form have been found for light loads and also for heavy loads at which contact is almost complete. The variation of the mean separation with load, which determines the volume of the space trapped between the two surfaces, is also found.     

An Investigation into Glucose as a Potential Precursor of N-Nitrosothiazolidine in Bacon

The possible involvement of glucose in the formation of N-nitrosothiazolidine (NTHZ) in bacon was investigated by pumping pork bellies with brines containing added glucose (2 and 4%). Raw bacon samples processed with glucose had significantly lower levels of N-nitrosothiazolidine-4-carboxylic acid than the smoked control bacons. When the bacon samples with glucose were fried for 6 and 12 min, no NTHZ was detected in the fried products. N-Nitrosopyrrolidine (NPYR) levels in these samples were much lower than those in the fried control samples. Results of this study demonstrate that the contribution of glucose to NTHZ formation in bacon is minimal relative to that of formaldehyde in the wood smoke.     

Discrete singular convolution and its application to the analysis of plates with internal supports. Part 2: Applications

Part 2 of this series of two papers presents the applications of the discrete singular convolution (DSC) algorithm. The main purpose of this paper is to explore the utility, test the accuracy and examine the convergence of the proposed approach for the vibration analysis of rectangular plates with internal supports. Both partial internal line supports and complex internal supports are considered for 21 square plates of various combinations of edge support conditions. The effects of different size, shape and topology of the internal supports and different boundary conditions on the vibration response of plates are investigated. The partial internal line supports may vary from a central point support to a full range of cross or diagonal line supports. Several closed‐loop supports, such as ring, square and rhombus, and their combinations are studied for complex internal supports. Convergence and comparison studies are carried out to establish the correctness and accuracy of the DSC algorithm. The DSC results are compared with those in the available literature obtained by using other methods. Numerical results indicate that the DSC algorithm exhibits controllable accuracy for plate analysis and shows excellent flexibility in handling complex geometries, boundary conditions and support conditions. Copyright © 2002 John Wiley & Sons, Ltd.     

Optimization of Automated Synthesis of 2-[18F]Fluoro-2-deoxy-D-glucose Involving Base Hydrolysis

Synthesis of 2-[¹⁸F]fluoro-2-deoxy-D-glucose ([¹⁸F]FDG) involving base hydrolysis was optimized. Fluorine-18 was isolated from irradiated water to more than 90% by sorption of [^{1 8}F]fluoride on QMA anion-exchange resin, which was followed by elution with a 96 : 4 (by volume) acetonitrile-water mixture containing Kryptofix 2.2.2 and potassium carbonate (molar ratio 2 : 1). This composition is the best for preparing the complex [K/K2.2.2]^{+ 18}F^- used in nucleophilic fluorinations. No additional azeotropic drying is required. Base hydrolysis under optimized conditions (40-45°C), followed by neutralization with HCl, removal of traces of the solvent, and purification of the final product on a combined SCX/Alumina N column, yielded [^{1 8}F]FDG of high radiochemical (>99%) and chemical purity with minimal product loss. With an RB-86 robotic system (Anatech, Sweden), the synthesis time was 38 min. The procedure is used in the Institute of Human Brain, Russian Academy of Sciences for routine synthesis of FDG; the radiochemical yield of the product by the end of synthesis (EOS) is reproducibly high: 63±3% (n = 40).