Interaction effects of multiple pool fires

What are the effects of flame behavior of a number of fires burning in close proximity to one another? The results of measurements of burning rates, heat feedback, flame height, and flame trailing are reported for fires involving liquid pools.     

Studies on oxidation of benzo [a] pyrene by sunlight and ozone

The destruction of the carcinogen benzo[a]pyrene (BaP) by light is well known; laboratory workers are routinely advised to cover fluorescent lamps with yellow filters while treating samples containing BaP. However until recently the mechanism of oxidation by sunlight and ozone had not been studied in detail. Concentrations of benzo[a]pyrene in urban air are in the range of 5–10 μg/1000 m³. Oxidant concentrations (predominantly in the form of ozone) are reported to be in the range of 0.01 ppm (22 μg per m³). Thus a sampling system with a filter paper would filter about 22,000 μg of ozone passing through and collect about 5 μg of BaP for analysis. The effect of interactions of such large ozone concentrations with BaP deposited on the filter paper is reported; data for the oxidation rates for benzo[a]pyrene coated on quartz surface and exposed to ozone or sunlight are presented. The oxidation products were analysed by thin-layer chromatography and highpressure liquid chromatography. From about eight products detected in these experiments, three have been identified as quinones based on UV-absorption spectrometry and mass spectrometry. Oxidation rates as high as 100% per hour of exposure are observed when less than 0.1 μg of BaP is coated inside the quartz tubes and exposed to ozone or sunlight. Oxidation rates for benzo[a]pyrene (using tritiated BaP) were determined for two types of experimental conditions. In the first set, tritiated BaP was spotted onto a glass fibre paper and sampling continued for 24 h; the loss of BaP was found to be 88%. In the second set tritiated BaP was spotted at intervals of one hour, for eight hours, while sampling is being carried out and the loss of BaP during the period was estimated to be 50%.     

The impact of using chilled water storage systems on the performance of air cooled chillers in Kuwait

In the air conditioning (AC) industry chilled water storage (CWS) systems are one form of cool thermal storage technology that can be used to time shift the electrical load of the system from the peak day periods to off peak night time periods. In this paper the data for the actual exported and generated electrical energy obtained for the power stations in Kuwait has been used to estimate the electrical energy consumption and the peak electrical load of AC systems. Since the chiller in an air cooled AC system represent more than 75% of the total electrical power consumed by an AC system during the peak demand period, the impact of using CWS systems with alternative operating strategies including partial (load levelling), partial (demand limiting) and full load has been investigated. In our conclusions we estimate that approximately 45% of the total annual exported electrical energy is consumed solely by AC systems as a result of the very high ambient temperatures occurring between March and October. Furthermore, it is estimated AC systems represent about 62% of the peak electrical load. The results demonstrate that CWS can reduce the peak electrical load of a chiller in an air cooled AC system by up to 100% and reduce the nominal chiller size by up to 33% depending upon the operating strategy adopted. This is achieved with only a 4% increase in power consumption of the chiller for all CWS strategies except for full storage where the energy consumption actually decreases by approximately 4%.     

A digital wind gust recorder

The instrument was a byproduct of an undergraduate final year project on wind power which was carried out by the Department of Mechanical Engineering of the University of Liverpool.The windmill test site was on an exposed, rocky island where there was no history of weather recording but a long tradition of violent winds.Field experience during the winter months suggested that corrosion fatigue arising from wind buffeting and salt spray would rank equally with maximum wind pressure as criteria of failure and if modern materials, so convenient for forming aerodynamic surfaces, were to be used then limited life concepts would need to be considered. This called for more knowledge of wind variations at the test site. A complete wind spectrum taken on chart recording instruments would have been ideal but since such such refined devices were not available the instrument to be described was designed.The only wind measuring instrument which was available was a rotating cup anemometer. This supplied an alternating voltage proportional to its rotational speed. It also operated a gear driven microswitch which could give an integrated “miles of wind” reading on an electromagnetic counter.Briefly the e.m.f. generated by the anemometer (Fig. 1) was matched against a pre-set voltage corresponding to the required gust velocity. When this was exceeded an appropriate counter was operated. Only the rising e.m.f. was significant. The subsequent fall was ignored. Initially three stages were incorporated which reported the gusts rising through forty, fifty and sixty knots, respectively. These recorded on separate counters. All basic settings were based on pitot-static speed determinations in a wind tunnel.     

Combined biological and ozone treatment of log yard run-off

Batch biological treatment of log yard run-off reduced biochemical oxygen demand (BOD), chemical oxygen demand (COD) and tannin and lignin (TL) concentration by 99%, 80%, and 90%, respectively. Acute (Microtox) toxicity was decreased over treatment, from an initial EC50 of 1.83% to a value of 50.4% after 48 h of treatment. Kinetics of biodegradation were determined using respirometry and fitted using the Monod and Tessier model. For the Monod model the maximum substrate uptake rate, and Ks values determined were 0.0038 mg BOD/mgVSS min, and 1.4 mg/L, respectively. The efficacy of ozone as a pre- and post- biological treatment stage was also assessed. During ozone pretreatment, TL concentration and acute toxicity were rapidly reduced by 70% and 71%, respectively. Pre-ozonation reduced BOD and COD concentration by < 10%, however a larger fraction of residual COD was non biodegradable after ozonation. Biologically treated effluent was subjected to ozonation to determine whether further improvements in effluent quality could be achieved. A reduction in COD and TL concentration was observed during ozonation, however no further improvement in toxicity was observed. Ozonation increased BOD by 38%, due to conversion of COD to BOD.     

The effect of a sprinkler on the stability of a smoke layer beneath a ceiling

A study has been made of the effect of sprinkler sprays on hot buoyant smoke layers with particular reference to covered shopping malls.     

Heavy metals in maternal and cord blood

Heavy metal concentrations have been determined in maternal and cord blood samples collected from mothers in the age group 20-25 years with full-term neonates (37-40 weeks). The concentrations of Pb, Cd, Cu and Zn were found to be low in cord blood as compared to mother's blood and the ratio between cord blood and maternal blood for the respective elements was found to be approximately 0.80, 0.86, 0.47 and 0.40. On the other hand, the concentrations of Fe and Mg in the mother's blood were found to be lower than those in the cord blood. Prenatal exposure to lead in Mumbai, though low (5.1 microg/dl), is approximately 2-3 times higher than that observed in Canada or Italy. A strong correlation (r = 0.79) between the maternal and cord blood lead levels has been observed during the present study.     

Application of GaN-based ultraviolet-C light emitting diodes--UV LEDs--for water disinfection

GaN-based ultraviolet-C (UV-C) light emitting diodes (LEDs) are of great interest for water disinfection. They offer significant advantages compared to conventional mercury lamps due to their compact form factor, low power requirements, high efficiency, non-toxicity, and overall robustness. However, despite the significant progress in the performance of semiconductor based UV LEDs that has been achieved in recent years, these devices still suffer from low emission power and relatively short lifetimes. Even the best UV LEDs exhibit external quantum efficiencies of only 1-2%.The objective of this study was to investigate the suitability of GaN-based UV LEDs for water disinfection. The investigation included the evaluation of the performance characteristics of UV LEDs at different operating conditions as well as the design of a UV LED module in view of the requirements for water treatment applications. Bioanalytical testing was conducted using Bacillus subtilis spores as test organism and UV LED modules with emission wavelengths of 269 nm and 282 nm.The results demonstrate the functionality of the developed UV LED disinfection modules. GaN-based UV LEDs effectively inactivated B. subtilis spores during static and flow-through tests applying varying water qualities. The 269 nm LEDs reached a higher level of inactivation than the 282 nm LEDs for the same applied fluence. The lower inactivation achieved by the 282 nm LEDs was compensated by their higher photon flux. First flow-through tests indicate a linear correlation between inactivation and fluence, demonstrating a well designed flow-through reactor. With improved light output and reduced costs, GaN-based UV LEDs can provide a promising alternative for decentralised and mobile water disinfection systems.     

Trace-metal concentrations in normal human liver: methods to cope with marked variability

Concentrations of trace elements in human tissues characteristically vary widely, and the distributions of most concentrations are skewed to the right. Examination of some of the factors which contribute to the marked variability and skewness of the concentrations revealed that: (1) distributions of concentrations are satisfactorily normal (Gaussian) after logarithmic transformation, (2) ash weight is the best frame of reference in which to report results, (3) the distributions of metal concentrations are not further normalized by adjustments which assume that tissue lipid or collagen contains a fixed fraction of the metal found in the parenchyma, and (4) the choice of sample site within the liver is of minimal significance.     

Impact wave propagation in tall buildings using advanced spectral element method

One of the major divisions in analysis and design of tall buildings is to account for forces induced by flying‐object impact and the subsequent progressive collapse. During the past three decades, problems of contact mechanics have been considered by some authors, and special attention has been devoted to high‐speed impact. Impact wave propagation in tall buildings may be analysed using the conventional finite element method. However, in order to guarantee stability and accuracy of the solution, the number of elements used to model the structure may be very large indeed; more precisely, accurate results can be obtained after a substantial computational effort. In this respect, an improved complex spectral element method is developed for analysing the wave propagation problems in large structures. The purpose of this paper is to obtain the resulting dynamic responses of a tall building induced by a high‐speed impact of a flying object. Copyright © 2003 John Wiley & Sons, Ltd.