Study of the effect of BDMA catalyst in the epoxy novolac curing process by isothermal DSC

Epoxy novolac/anhydride cure kinetics has been studied by differential scanning calorimetry under isothermal conditions. The system used in this study was an epoxy novolac resin (DEN431), with nadic methyl anhydride as hardener and benzyldimethylamine as accelerator. Kinetic parameters including the reaction order, activation energy and kinetic rate constants, were investigated. The cure reaction was described with the catalyst concentration, and a normalized kinetic model developed for it. It is shown that the cure reaction is dependent on the cure temperature and catalyst concentration, and that it proceeds through an autocatalytic kinetic mechanism. The curing kinetic constants and the cure activation energies were obtained using the Arrhenius kinetic model. A suggested kinetic model with a diffusion term was successfully used to describe and predict the cure kinetics of epoxy novolac resin compositions as a function of the catalyst content and temperature. Copyright © 2003 Society of Chemical Industry     

Oligo(ethylene oxide) side‐chain steric screening effects on conductimetric properties of grafted poly(4‐vinylpyridinium) salts in aqueous solutions

A set of poly[N‐oligo(ethylene oxide)yl 4‐vinylpyridinium tosylate] (P4VOEOOTs) has been prepared by spontaneous polymerization of 4‐vinylpyridine. This method gives a grafted polyelectrolyte having a positive charge on every backbone pyridinic moiety. The P4VP15Ts, P4VP164Ts, P4VP350Ts and P4VP750Ts aqueous solution conductivities were determined in the concentration range from 6 × 10^?4 to 10^?2 M at 25 °C. The variation of the conductivity versus concentration of the investigated system exhibits typical polyelectrolyte behaviour. The polyelectrolyte mobility was found to be dependent on the oligo(ethylene oxide) (OEO) side‐chain length. Manning's rod‐like model fails to describe these results. A simple steric effect is proposed to explain the influence of the OEO length. Copyright © 2003 Society of Chemical Industry     

Flow Reaction Forces upon Blowdown of Safety Valves

The activation of safety valves causes the development of flow reaction forces that have to be transferred in an adequate way via the piping to the steel structure or via the connected vessel into the foundation. If the safety valve outlet piping is connected to a blowdown system or, in case of blowing off into the atmosphere, are equipped with a T‐piece at the outlet, the stationary reaction forces are compensated completely. The transient opening process, however, develops flow reaction forces which culminate in peaks of short duration. In this article, a simple method will be proposed for the estimation of the resulting reaction forces as a function of the length of the pipe at the safety valve outlet. CFD calculations and blowdown tests executed with a full‐lift safety valve have confirmed this method on principle. Special importance is attributed to the short duration of the effect of the reaction forces which seems to have only a negligible impact on the supporting steel structure.     

Catalytic aminolysis of epoxide by alumina prepared from amine-protected Al precursor

The catalytic activities of alumina prepared from an Al alkoxide-amine adduct monomer for the reaction of cyclopentene oxide with piperidine was determined after various pretreatments, including calcination and exposure to moisture. They were compared with the activity of alumina prepared by the conventional hydrolysis method. It was found that the as-prepared sample from the alkoxide-amine monomer preparation was five times more active than a conventional preparation, suggesting that it has a higher density of surface Lewis acid sites. However, its activity was much more severely suppressed by exposure to moisture.     

Nonlinearity analysis and optimization of HBTs for optical mixer designs

Two types of photo heterojunction bipolar transistor (HBT) to directly down-convert optical signals to electronic signals have been reported in the literature: a conventional photo-HBT in which light penetrates through the area of the base-collector junction and an HBT where light shines through the base-collector edge for higher conversion efficiency. Although the performance in relation to bias conditions has been published, the detailed analyses for identifying the parameters and bias conditions that provide optimum direct down-conversion have not been examined. This paper provides a full explanation of the operation of the down-conversion for both HBT configurations based on low-frequency analyses. Such information is useful for both understanding the nonlinear mechanisms involved and designing for maximum efficiency. In addition, a new circuit has been developed from the basic HBT down-conversion circuit that provides improved performance.     

Radiometric sensor for temperature control of food processing

This paper describes a novel planar antenna sensor created for the purpose of noninvasive temperature measurements using microwave radiometry. In order to improve radiometric measurements in industrial applications, a new generation of sensors is introduced, composed of a metallic sheet. Simulations based upon the method of moments is used both to design and to determine their electromagnetic performances. This paper also describes a radiometric device using these sensors to measure and control the temperature of food products during deep freezing processes. The results and discussions are presented.     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.