Mechanical properties and thermal stability of double‐shell thermal‐energy‐storage microcapsules

Double‐shell‐structured microcapsules encapsulating phase‐change materials (micro‐PCMs) with an average diameter of 5–10 μm were successfully fabricated with a melamine–formaldehyde resin as the coating material. The mechanical properties of the obtained piled micro‐PCMs, tested under compression, were evaluated with a pressure sensor. Typical stress–strain curves showed that both the single‐shell‐ and double‐shell‐structured microcapsules had yield points and maximum point pressures. The morphological changes in the shell surface confirmed the existence of yield points by scanning electron microscopy. When the pressure was beyond the yield point, the microcapsules showed conventional plastic behavior, and the double‐shell structure was more mechanically stable than the single‐shell one. Differential scanning calorimetry analysis results revealed that the properties of the phase‐change materials experienced no variation after coating with a single‐shell‐ or double‐shell‐structured polymer. Thermogravimetric analysis showed that the double‐shell‐structured micro‐PCMs experienced a weight loss of only about 5% from 86.3 to 232°C but did so more rapidly from 232 to 416°C. Thermoregulation was determined with periodical heating and cooling tests. The data showed that the micro‐PCMs changed temperature in a narrow range of 20–25°C with a time lag of 20 min to reach the maximum or minimum temperature in comparison with a reference temperature of 18–28°C. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1295–1302, 2007     

复杂制品注塑成型模拟分析

应用CAE软件MoldflowPlasticsInsight4.1的充模、保压、冷却、翘曲等分析模块,对汽车尾门饰件注塑成型过程进行CAE分析,研究了浇口位置、工艺参数等对制品性能的影响。最后,基于模拟结果分析了制品翘曲的主要原因,为模具设计及注塑工艺的确定提供参考。     

高固体分丙烯酸树脂相对分子质量的研究

采用溶液聚合法合成高固体分丙烯酸树脂,用凝胶渗透色谱(GPC)法分析引发剂的种类和用量、反应温度及聚合工艺对丙烯酸树脂的相对分子质量及其分布的影响。结果表明,选用偶氮二异丁腈和过氧化苯甲酰两种引发剂进行复配可提高聚合物的相对分子质量;采用“饥饿态”聚合工艺进行聚合反应可有效控制聚合物的相对分子质量,且相对分子质量分布均匀,分散度小于2;当引发剂用量为2%,在110℃的反应条件下制得的丙烯酸树脂的综合性能优异,固含量超过70%,相对分子质量可达4万。     

Structure and properties of regenerated cellulose films coated with polyurethane–nitrolignin graft‐IPNs coating

A regenerated cellulose film (RC) was coated with a graft‐IPNs coating, which was composed of castor oil‐based polyurethane and 2.8 wt % nitrolignin (NL), to obtain water‐resistant films. The effects of NCO/OH molar ratio and different polyols, such as 1,4‐butanediol (BDO) and trimethanol propane (TMP), on the structure and properties of the coated RC films were investigated. With an increase of the NCO/OH molar ratio, the tensile strength of the coated films increased, but the water resistivity and size contraction hardly changed. The coated films with TMP exhibited the higher breaking elongation at 1.5 of the NCO/OH molar ratio, while those with BDO have more excellent tensile strength, water resistivity, and dimensional stability. The coated films with the graft‐IPNs coating exhibited superior water resistivity and dimensional stability. The light transmittance of the coated films was more excellent than that of the RC film. Moreover, the results from the IR and electron probe microanalysis (EPMA) showed that the chemical bonding occurred between cellulose and coating, and the introduction of NL plays an important role in the enhancement of the interface adhesion of the coated films. Atomic force microscopy (AFM) depicted the flat and dense surface of the coated films, which restricted the water vapor penetration and the size contraction, resulting in the enhancement of water resistivity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1799–1806, 2002     

低密度冷模塑聚氨酯软质泡沫塑料

介绍了低密度冷模塑聚氨酯软质泡沫塑料的配方体系，工艺特点及泡沫性能。指出该泡沫应用范围较广，发展前景甚好。     

Subsolidus Phase Relationships in Si3N4–AlN–Rare-Earth Oxide Systems

The subsolidus phase relationships in Si₃N₄–AlN–rare-earth oxide (Me₂O₃ where Me=Nd, Sm, Gd, Dy, Er, and Yb) systems were studied. Solid-solution regions with the α-Si₃N₄ structure were delineated along the Si₃N₄–"Me₂O₃:9AIN" joins for all of the rare-earth oxide systems studied. The solubility limits of these solid solutions increased with decreasing size of the rare-earth ions.     

微波辅助萃取鱼香草挥发油工艺的研究

利用正交实验研究微波辅助萃取鱼香草挥发油的工艺条件。考察了微波辐射时间、微波功率、溶剂用量、洗涤滤饼的溶剂量对提取率的影响。实验结果表明,微波萃取的最佳工艺条件：辐射时间60s,微波功率288w,溶剂用量120ml,洗涤滤饼溶剂量20ml。     

丙烯酸酯改性双环戊二烯酚型环氧树脂及其性能研究

通过FT－IR光谱表征了丙烯酸酯改性的DCPD酚型环氧树脂／DDM体系结构，并通过测定改性体系的凝胶时间和分析凝胶时间的影响因素，研究了该体系的反应特性，同时，对改造前后DCPD酚型环氧树脂体系的性能做了分析。     

灰色—支持向量机的空调负荷预测

对空调负荷进行准确预测不仅对空调优化控制的意义重大,而且也是实现空调经济运行与节能的关键所在。为了提高建筑空调负荷的预测精度,在分析灰色模型和支持向量机建模特点基础上提出了一种空调负荷组合预测算法。该方法综合了灰色建模计算过程简单以及支持向量机自学习和泛化能力强的优点,能够更加有效地利用样本数据的有效信息,提高模型预测精度。首先,通过灰色建模过程弱化了样本数据的随机因素。然后,对灰色模型输出进行归一化处理及数据重构,以作为支持向量机的输入。最后,通过支持向量机模型的预测得到最终预测结果。将本文所提出的方法应用于福州一栋办公建筑的逐时空调负荷预测中,并与灰色模型及支持向量机模型作比较,证明了组合模型的预测值与实际运行值拟合度最高,平均绝对误差比灰色模型和支持向量机模型分别降低了47.84%和17.39%。该组合预测模型具有较高的预测精度和更好的泛化能力,具有较强的可行性和实用性。     

分析用水对陶瓷铅溶出量测定的影响

分析用水水质对日用陶瓷铅溶出量测定具有重要影响,CL-、SO42-、CO2等严重抑制铅的溶出,使测定结果偏低。