Hydrolysis of tetracalcium phosphate in H3PO4 and KH2PO4

The activity product of tetracalcium phosphate (TTCP, Ca₄(PO₄)₂O), was determined at 37°C, and the hydrolysis of TTCP was investigated in 0.01–0.1 mol l^–1 H₃PO₄ and KH₂PO₄ solutions by means of calcium and phosphorus analyses, X-ray diffraction and infrared analysis. The activity product, defined as K _sp=(Ca²⁺)⁴ (PO ₄ ^3– )² (OH^–)², was 37.36 as pK _sp, which was smaller than that previously reported (42.4). TTCP easily hydrolysed to form calcium-deficient apatite (Ca-def OHAp, Ca_5–x (HPO₄) _x (PO₄)_3–x (OH)_1–x ), or dicalcium phosphate dihydrate (DCPD, CaHPO₄2H₂O), depending on the initial phosphate concentration. With 0.1 mol l^–1 H₃PO₄, TTCP hydrolysed to form DCPD within several minutes. In 0.025 mol l^–1 H₃PO₄ and 0.1 mol l^–1 KH₂PO₄, TTCP hydrolysed to form Ca-def OHAp through DCPD. In the latter solution, a small amount of octacalcium phosphate (OCP, Ca₈(H₂PO₄)₂(PO₄)₄5H₂O), was detected as an intermediate product. In 0.025 mol l^–1 KH₂PO₄, TTCP hydrolysed directly to form Ca-def OHAp. In 0.01 mol l^–1 H₃PO₄, hydrolysis of TTCP was not completed, although Ca-def OHAp was only a product. Thus the final product and the degree of hydrolysis depended on the pH and the overall Ca/P ratio in the reaction system. The rate of Ca-def OHAp formation seemed to be controlled by the dissolution rate of TTCP rather than the crystallization rate of the OHAp.     

The use of doped polyaniline as an electrode in the galvanic anodic protection of ferrous metals in industrial acid solutions

In order to investigate the galvanic anodic protection (GAP) of ferrous metals (such as 410, 304 and 316 stainless steels) in acid solutions by doped polyaniline (PANi), separate doped PANi powder-pressed electrodes with different surface areas (the area ratio of the PANi electrode to stainless steel is between 1:1 and 1:2) have been prepared. These were coupled with ferrous metal in the following solutions: 5 M sulphuric acid, 5 M phosphoric acid and industrial phosphoric acid (containing 5 M phosphoric acid and 0.05% chloride ion) to construct a galvanic cell, in which PANi is cathode while ferrous metal is anode. The results indicate that a PANi electrode with sufficient area can provide corrosion protection to stainless steel in these acidic solutions. A pilot scale coupling experiment was carried out. The results indicate that PANi is a promising material as an electrode for the anodic protection of ferrous metals in acidic solutions in industrial situations.     

Comparative hall measurements on wet- and dry-oxidized 4H-SiC MOSFETs

Hall measurements have been used to compare the properties of 4H-SiC inversion-mode MOSFETs with “wet” and “dry” gate oxides. While the field-effect mobilities were approximately 3–5 cm²/Vs, the Hall mobilities in 4H-SiC MOSFETs in the wet and dry oxide samples were approximately 70–80 cm²/Vs. The dry-oxidized metal oxide semiconductor field effect transistors (MOSFETs) had a higher transconductance, improved threshold voltage, improved subthreshold slope, and a higher inversion carrier concentration compared to the wet-oxidized MOSFETs. The difference in characteristics between the wet- and the dry-oxidized MOSFETs is attributed to the larger fixed oxide charge in the dry oxide sample and a higher interface trap density in the wet oxide sample.     

A transmit/receive IF chip set for WCDMA mobiles in 0.35 /spl mu/m CMOS

An implementation of the IF section of WCDMA mobile transceivers with a set of two chips fabricated in an inexpensive 0.35-/spl mu/m two-poly three-metal CMOS process is presented. The transmit/receive chip set integrates quadrature modulators and demodulators, wide dynamic range automatic gain control (AGC) amplifiers, with linear-in-decibel gain control, and associated circuitry. This paper describes the problems encountered and the solutions envisaged to meet stringent specifications, with process and temperature variations, thus overcoming the limitations of CMOS devices, while operating at frequencies in the range of 100 MHz-1 GHz. Detailed measurement results corroborating successful application of the new techniques are reported. A receive AGC dynamic range of 73 dB with linearity error of less than /spl plusmn/2 dB and spread of less than 5 dB for a temperature range of -30/spl deg/C to +85/spl deg/C in the gain control characteristic has been measured. The modulator measurement shows a carrier suppression of 35 dB and sideband/third harmonic suppression of over 46 dB. The core die area of each chip is 1.5 mm/sup 2/.     

Performance evaluation of a multichannel transceiver system forADSL and VHDSL services

The authors study the performance of a multichannel modulation method for asymmetric digital subscriber lines (ADSLs) and very high-speed digital subscriber lines (VHDSLs). In the ADSL case, over all unloaded North American subscriber lines in the test set, a unidirectional 1.536 Mb/s data rate service from the end office to the customer premises is possible on a single twisted pair at an error rate of 10^-7 with at least a 6 dB margin used coded multichannel modulation with sufficient transmit power. In the VHDSL case, data rates in excess of 100 Mb/s can be transmitted reliably, at an error rate of 10^-7, using uncoded multichannel modulation on a single twisted pair over a distance ⩽150 ft with a sufficiently high sampling rate (≈24 MHz) and transmit power. It is shown that a cost-effective multichannel transceiver design suggested for high-speed digital subscriber line (HDSL) service will also work well for ADSL and VHDSL services with only minimal modifications     

An anisotropic theory of elasticity for continuum damage mechanics

This paper presents the development of an anisotropic elastic damage theory. This is achieved by deriving a modified damage effect tensor M(D) for the effective stress equations capable of including the effect of anisotropic material damage. The modified tensor removes the restriction of a priori knowledge of the directions of principal stresses imposed by a damage effect tensor developed earlier and can now be made for general practical engineering applications of failure analysis. Reduction of the proposed tensor to a scalar for isotropic damage is shown to be possible when it is expressed not only in the principal directions but also in any arbitrary coordinate system, a necessary condition to verify the validity of the proposed tensor. Uniaxial tension and pure torsion are chosen to illustrate the application of the theory as well as associated damage variables that may be experimentally determined using laboratory size specimens. The measured damage variables confirm the presence of anisotropic damage from an initially isotropic material specimen and the magnitude is more pronounced at higher stresses and strains.

---

Résumé On présente un développement d'une théorie sur l'endommagement élastique anisotrope en déduisant un tenseur modifié décrivant l'effet de l'endommagement pour un système d'équations de contraintes effectives susceptible d'inclure l'effet d'un endommagement dans un matériau anisotrope. Le tenseur modifié supprime la restriction de la connaissance a priori des directions des contraintes principales imposées par un tenseur d'effet d'endommagement développé précédemment; il peut à présent entrer dans les applications pratiques en construction de l'analyse des ruptures.On montre qu'il est possible de réduire le tenseur proposé à une valeur scalaire dans le cas d'un dommage isotrope, dès lors qu'il est exprimé non seulement suivant les directions principales, mais dans un système de coordonnées arbitraires, ce qui est une condition nécessaire pour en vérifier la validité.On choisit une traction multiaxiale et une torsion pure pour illustrer l'application de la théorie ainsi que des variables d'endommagement associées, susceptibles d'être déterminées expérimentalement à l'aide d'éprouvettes de laboratoire.Les variables d'endommagement mesurées confirment la présence d'un dommage anisotrope dans le cas d'une éprouvette d'un matériau initialement isotrope; son amplitude est plus prononcée à des contraintes ou des déformations plus importantes.

     

微波辐射电镜生物样品制备方法研究

本文报道一种快速微波辐射电镜样品制备方法──水浴法，以及这个方法在动植物样品超薄切片制备中的应用。实验结果表明，水浴法使得样品可以接受相对较长时间的微波辐射而不致造成任何损伤，浸泡液和样品的温度控制简单而且准确，样品处理的结果内外均匀一致，超微结构保存优秀，完全可与常规制样法和Ｌｏｇｉｎ法的结果相媲美，而且在某些方面水浴法要优于常规法和Ｌｏｇｉｎ法。     

烷基化原料预加氢工艺应用分析

由于来自催化裂化装置的烷基化原料中所含有的丁二烯在烷基化反应中可生成重质油,使产品干点上升,辛烷值下降,并使酸耗增加.针对这种状况,齐鲁石化公司研究院和胜利炼油厂联合开发了QSH-01烷基化原料预加氢催化剂及其相应的工艺技术,来脱除原料中丁二烯.笔者对该工艺技术及其应用作了阐述,并对该技术的应用前景作出分析.