Infrared study of salt free and salt treated cellulose pyrolysis under nitrogen atmosphere

The pyrolysis under nitrogen of salt free and salt treated cellulose was studied by infrared spectroscopy. The results confirm the unzipping mechanism suggested by DTA and TGA studies, and show this mechanism to apply to the untreated and salt treated samples. The results also show the unzipping to stop at the stage of char formation. The onset of this stage was found to occur after the volatilization of only 45–50% of the initial sample of the borax treated cellulose, compared with 65–70% of the KCl treated cellulose and 80–85% of the untreated cellulose.     

Target following with motion prediction for unmanned surface vehicle operating in cluttered environments

The capability of following a moving target in an environment with obstacles is required as a basic and necessary function for realizing an autonomous unmanned surface vehicle (USV). Many target following scenarios involve a follower and target vehicles that may have different maneuvering capabilities. Moreover, the follower vehicle may not have prior information about the intended motion of the target boat. This paper presents a trajectory planning and tracking approach for following a differentially constrained target vehicle operating in an obstacle field. The developed approach includes a novel algorithm for computing a desired pose and surge speed in the vicinity of the target boat, jointly defined as a motion goal, and tightly integrates it with trajectory planning and tracking components of the entire system. The trajectory planner generates a dynamically feasible, collision-free trajectory to allow the USV to safely reach the computed motion goal. Trajectory planning needs to be sufficiently fast and yet produce dynamically feasible and short trajectories due to the moving target. This required speeding up the planning by searching for trajectories through a hybrid, pose-position state space using a multi-resolution control action set. The search in the velocity space is decoupled from the search for a trajectory in the pose space. Therefore, the underlying trajectory tracking controller computes desired surge speed for each segment of the trajectory and ensures that the USV maintains it. We have carried out simulation as well as experimental studies to demonstrate the effectiveness of the developed approach.     

Al2O3─SiC Composites from Aluminosilicate Precursors

Al₂O₃ and SiC composite materials have been produced from mixtures of aluminosilicates (both natural minerals and synthetic) and carbon as precursor materials. These composites are produced by heating a mixture of kaolinite (or synthetic aluminosilicates) and carbon in stoichiometric proportion above 1550°C, so that only Al₂O₃ and SiC remain as the major phases. A similar process has also been used for synthesizing other composite powders having mixtures of Al₂O₃, SiC, TiC, and ZrO₂ in different proportions (all compounds together or selective mixtures of some of them), as desired. The microstructure of hot-pressed dense compacts, produced from these powders, revealed that the SiC phase is distributed very homogeneously, even occasionally within Al₂O₃ grains on a nanosize scale. The homogeneous distribution of SiC particles within the system produced high fracture toughness of the hot-pressed material (K_IC∼ 7.0 MPa · m^1/2) and having Vicker's hardness values greater than 2000 kgf/mm².     

Analysis of sucrose mono- And diesters prepared from triglycerides containing C12 @#@ C18 Fatty Acids

A quantitative gas liquid Chromatographic method of analysis for sucrose mono- and diesters, prepared from naturally occurring triglycerides, is described. For esters containing predominantly C₁₆C_1s alkyl groups, a common calibration curve was obtained. Calibration standards were prepared by column chromatography using silica gel adsorbent. Methods of analysis for the major impurities present in the sucrose mono- and diesters are also described.     

Melt rheology and morphology of PP/SEBS/PC ternary blend

Melt rheological properties of the ternary blend of isotactic polypropylene (PP), styreneethylene–butylene–styrene terpolymer (SEBS), and polycarbonate (PC), PP/SEBS/PC, are studied in a wide range of composition, such that PP is the matrix and SEBS and PC are the minor components, with the proportion of one varying from 0 to 30% at various fixed compositions of the other. The respective binary blends, PP/SEBS and PP/PC, studied as the reference systems for interpretation of results on the ternary blends yielded interesting new information about the morphology development and its correlation with melt rheological properties of these binary blends. The studies include the measurement of melt rheological properties on a capillary rheometer in the shear rate range 10¹–10⁴ s^?1 at a fixed temperature of 240°C. The data presented as conventional flow curves are analyzed for the effect of blend composition and shear rate on pseudoplasticity, melt viscosity, and melt elasticity, and role of each individual component is identified. Morphology of dispersed phases of these blends is studied through scanning electron microscopy of the cryogenically fractured and suitably etched surfaces. Variations of morphology with blend composition and shear rate showed interesting correlation with melt rheological properties, which are discussed in detail. An important finding of the morphological studies is that in the PP/SEBS/PC ternary blend the SEBS phase forms two types of morphologies depending on the blend composition and shear rate: (i) simple droplets and (ii) boundary layer at the surface of the PC droplets. © 1993 John Wiley & Sons, Inc.     

Studies in a modified cadoxen solvent

A cadmium ethylenediamine solvent (cadoxen) of modified composition containing 0.5 M sodium hydroxide, 5% cadmium, and 28–30 % ethylenediamine was found to dissolve high molecular cotton materials even under higher ambient temperature conditions as in India. The stability of cellulose solutions in this solvent was still high enough to enable viscosity measurements without exclusion of air. Intrinsic Viscosity values were determined for a large number of cellulosic materials. A study of the kinetics of degradation of cellulosic solutions in cadoxen gave comparatively higher rate constants in nitrogen atmosphere and a higher energy of activation as compared to other alkaline solvents indicating that degradation in cadoxen cannot be considered primarily oxidative in nature.     

Development of antimicrobial polypropylene sutures by graft copolymerization. II. Evaluation of physical properties,drug release,and antimicrobial activity

Polypropylene (PP) sutures are prepared by the simultaneous radiation grafting of 1‐vinylimidazole (VIm) onto PP monofilament sutures. The tenacity slightly decreases whereas the elongation increases with the increase in the degree of grafting. Thermogravimetric analysis shows that the stability of the sutures is enhanced by the grafting process. The grafted sutures have reasonably good water uptake. They are subsequently immobilized with an antimicrobial drug, ciprofloxacin. The modified suture releases the drug over a period of 4–5 days. The antimicrobial activity of the modified suture is determined against Esherichia coli by the zone of inhibition technique. A clear zone of inhibition is observed around the drug‐containing suture. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3534–3538, 2007     

Kinetics of vinyl polymerization initiated by potassium permanganate/β-hydroxybutyric acid redox system

The aqueous polymerization of acrylamide initiated by potassium permanganate/β-hydroxybutyric acid has been studied volumetrically at 35 ± 0.01°C in an inert medium. The rate of polymerization shows nearly square root dependence on β-hydroxybutyric acid at low concentration (3.12 – 12.5 · 10^?3 mol dm^?3). The order with respect to potassium permanganate has been found to be 0.6 indicating thereby a bimolecular mode of termination. The polymerization rate has been varied linearly at low monomer concentrations i.e. from 2.5 –7.0 · 10^?2 mol dm^?3. The dependence of number average degree of polymerization on the initial rate of polymerization and temperature has been determined. The over-all activation energy has been found to be 51.66 kJ mol^?1. A kinetic reaction scheme is proposed on the basis of experimental results.     

A model for transitional breakage probability of droplets in agitated lean liquid-liquid dispersions

A model for transitional breakage probability of droplets in agitated lean fiquid-liquid dispersions is proposed based on the mechanism of breakage of droplets due to their oscillations resulting from relative velocity fluctuations. A universal transitional breakage probability in terms of non-dimensionalized drop diameter is derived for all dispersed phases whose density and viscosity are almost the same as that of continuous phase. The maximum stable drop diameter d_s derived from the model, shows a dependence of N_We^?0.6. It is shown that a “power law” approximation Kvⁿ is valid for transitional breakage probability for d/d_s up to 2. The exponent 2.67, predicted by this model corresponds rather well with an estimate of 2, obtained from experimental observations. A functional relation for the rate constant K in terms of the parameters and physical properties of the system is derived. A universal non-dimensionalized equilibrium drop-size distribution for agitated lean liquid-liquid dispersions is derived by analytical solution of a population balance equation simplified by order of magnitude estimates. Interestingly enough, this analytical solution is the same as the Gaussian distribution suggested empirically by Chen and Middleman.     

Frying quality and stability of low-and ultra-low-linolenic acid soybean oils

To determine effects of very low levels of linolenic acid on frying stabilities of soybean oils, tests were conducted with 2% (low) linolenic acid soybean oil (LLSBO) and 0.8% (ultra-low) linolenic acid soybean oil (ULLSBO) in comparison with cottonseed oil (CSO). Potato chips were fried in the oils for a total of 25 h of oil use. No significant differences were found for either total polar compounds or FFA between samples of LLSBO and ULLSBO; however, CSO had significantly higher percentage of polar compounds and FFA than the soybean oils at all sampling times. Flavor evaluations of fresh and aged (1, 3, 5, and 7 wk at 25°C) potato chips showed some differences between potato chips fried in different oil types. Sensory panel judges reported that potato chips fried in ULLSBO and aged for 3 or 7 wk at 25°C had significantly lower intensities of fishy flavor than did potato chips fried in LLSBO with the same conditions. Potato chips fried in ULLSBO that had been used for 5 h and then aged 7 wk at 25°C had significantly better quality than did potato chips fried 5 h in LLSBO and aged under the same conditions. Hexanal was significantly higher in the 5-h LLSBO sample than in potato chips fried 5 h in ULLSBO. The decrease in linolenic acid from 2 to 0.8% in the oils improved flavor quality and oxidative stability of some of the potato chip samples.