Design of Lu2O3-reinforced Cf/SiC-ZrB2-ZrC ultra-high temperature ceramic matrix composites: Wetting and interfacial reactivity by ZrSi2 based alloys

The wettability and infiltration of molten ZrSi₂ and ZrSi₂-Lu₂O₃ alloys into C_f/SiC and B₄C-infiltrated C_f/SiC composites were investigated to understand the interfacial interactions that occur during the development of C_f/SiC-ZrC and C_f/SiC-ZrB₂-ZrC-Lu₂O₃ materials. A significant evaporation of Si from the liquid affected the wetting behaviour of the alloy when tested in a vacuum at 1670 °C. The better wetting and spreading of the alloy over the surface was observed for the composites with lower overall porosity (12 %). On the other hand, the formation of an outer dense layer, followed up by the uniform infiltrated region up to ～ 1 mm was observed for the C_f/SiC with higher porosity (21 %). The infiltrated alloy reacted with SiC matrix to form ZrC or with B₄C-infiltrated SiC matrix to form ZrB₂-ZrC-SiC. The Lu₂O₃ particles were not wetted by the melt, and were pushed away of the reaction zone by the solidification front.     

Biobased surfactant-like molecules from organic wastes: the effect of waste composition and composting process on surfactant properties and on the ability to solubilize Tetrachloroethene (PCE)

In this work, four surfactant-like humic acids (HAs) obtained from garden lignocellulose wastes and kitchen food wastes mixed with garden-lignocellulose wastes, both before and after composting, were tested for surfactant properties and the ability to solubilize tetrachloroethene (PCE). The waste-derived HAs showed good surfactant properties, lowering the water surface tension from 74 mN m(-1) to 45.4 +/- 4.4 mN m(-1), with a critical micelle concentration (CMC) of 1.54 +/- 1.68 g L(-1), which is lower than many synthetic ionic surfactants. CMC was affected by both waste origin and composting processes. The addition of food waste and composting reduced CMC by adding alkyl-C (measured by CP MAS 13C NMR) and N- and S-HA contents (amide molecules), so that a multistep regression was found [CMC = 24.6 - 0.189 alkyl C - 2.64 (N + S); R2 = 0.77, P < 0.10, n = 6]. The four HAs solubilized PCE at the rate of 0.18-0.47 g PCE/g aqueous biosurfactant. These results were much higher than those reported in the literature for a commercial HA (0.026 g/g), but they were in line with those measured in this work for nonionic surfactants such as Tween-80 (0.69 g/g) and Triton X-100 (1.08 g/g).     

Optimization of the working cycle for a hydrogen production and power generation plant based on aluminum combustion with water

The working cycle of a novel hydrogen and power generation system based on aluminum combustion with water is analyzed in order to evaluate the best performance in terms of energy conversion efficiency. The system exploits the exothermic reaction between aluminum and steam and produces thermal power for a super-heated steam cycle and hydrogen as a by-product of the reaction.     

Comparative analysis of the outdoor performance of a dye solar cell mini‐panel for building integrated photovoltaics applications

New generation photovoltaic (PV) devices such as polymer and dye sensitized solar cells (DSC) have now reached a more mature stage of development, and among their various applications, building integrated PVs seems to have the most promising future, especially for DSC devices. This new generation technology has attracted an increasing interest because of its low cost due to the use of cheap printable materials and simple manufacturing techniques, easy production, and relatively high efficiency. As for the more consolidated PV technologies, DSCs need to be tested in real operating conditions and their performance compared with other PV technologies to put into evidence the real potential. This work presents the results of a 3 months outdoor monitoring activity performed on a DSC mini‐panel made by the Dyepower Consortium, positioned on a south oriented vertical plane together with a double junction amorphous silicon (a‐Si) device and a multi‐crystalline silicon (m‐Si) device at the ESTER station of the University of Rome Tor Vergata. Good performance of the DSC mini‐panel has been observed for this particular configuration, where the DSC energy production compares favorably with that of a‐Si and m‐Si especially at high solar angles of incidence confirming the suitability of this technology for the integration into building facades. This assumption is confirmed by the energy produced per nominal watt‐peak for the duration of the measurement campaign by the DSC that is 12% higher than that by a‐Si and only 3% lower than that by m‐Si for these operating conditions. Copyright © 2013 John Wiley & Sons, Ltd.     

SOFC anodes for direct oxidation of hydrogen and methane fuels containing H2S

Single cell solid oxide fuel cells using Ni-YSZ and Co-YSZ anodes were tested in H₂, CH₄, H₂S/H₂ and H₂S/CH₄ fuel mixtures. Their performance was found to quickly degrade in dry CH₄ due to carbon deposition and lifting of the anode from the electrolyte. In contrast, hydrogen or methane containing H₂S showed an increase in exchange current densities when compared to H₂,M/YSZ/LSM,air systems (M = Ni or Co) despite having less optimal anode microstructure. Conversion from metal to metal-sulfide in the presence of H₂S produced large, dense metal-sulfide particles surrounded by YSZ, thus decreasing the triple-phase boundary. Furthermore, CoS-based anodes showed phase segregation and densification toward the electrolyte. Despite this, long-term testing at η_a = 0.5 V of the H₂S/CH₄,CoS-YSZ/YSZ/LSM,air system showed no signs of degradation of the anode over a 6-day period. Only after removal of H₂S from the H₂S/CH₄ stream did the CoS-anode reduce back to Co, signifying H₂S is required to maintain the metal-sulfide active anode.     

Ultrahydrophobic PMMA micro- and nano-textured surfaces fabricated by optical lithography and plasma etching for X-ray diffraction studies

Polymeric (PMMA) ultrahydrophobic surfaces with contact angles up to about 170° have been fabricated and used in the context of synchrotron radiation experiments on biological droplets. The different microfabrication processes included either an optical lithography phase followed by a plasma texturing one or a single step deep reactive ion etch attack.The drying of several biological solution droplets has been monitored. Room temperature evaporation experiments (lysozyme, lactalbumin, cytochrome C, doxorubicin and synthesized peptides) finally result in the formation of easily detachable hollow residuals because of the low interaction between the ultrahydrophobic substrate and the aqueous droplet while pilot experiments (bovine insulin) in a sitting-drop environment bring to the formation of well defined crystals. Recent results about in situ X-ray diffraction experiments by SAXS & WAXS (Small and Wide Angle X-ray Scattering) μ-beam techniques confirm that the presence of such surfaces influences the formation of crystal or fibril structures. These substrates represent indeed a suitable support to study biological and inorganic droplets in a near contact-free environment exploiting the homogeneous evaporation rate induced by the ultrahydrophobicity of the system.     

Optical micro-structures fabricated on top of optical fibers by means of two-photon photopolymerization

In this work we report, for the first time to our knowledge, the possibility to fabricate various structures, with good optical proprieties, on the top of optical fibers, using the two-photon lithography (TPL) technique. We show the convenience of this approach to quickly create generic 3D shapes using a single set-up by contrast to past shape-dependent methods. A set of different structures are fabricated and characterized to demonstrate the versatility of this approach and their high optical quality.     

Planar packing of trees and spider trees

In [A. García, C. Hernando, F. Hurtado, M. Noy, J. Tejel, Packing trees into planar graphs, J. Graph Theory (2002) 172-181] García et al. conjectured that for every two non-star trees there exists a planar graph containing them as edge-disjoint subgraphs. In this paper we prove the conjecture in the case in which one of the trees is a spider tree.