Telerobot-enabled HUB-CI model for collaborative lifecycle management of design and prototyping

The HUB-CI model is investigated in a telerobotic system in a client/server network to manage the lifecycle of engineering design and prototyping. The purpose of this platform is to support collaborative engineering design and proof of concept to enhance distributed team collaboration and resource utilization. The suggested platform is exemplified in two collaboration support tools and a physical prototyping platform. Structured Co-Insight Management is developed to support innovative idea exchanges and the consensus decision-making during the design process. Conflict/error detection management helps preventing conflicts and errors during the lifecycle of design and development. Physical collaboration over the network occurs when a team controls the telerobot operation during prototyping and testing in design cycles. A pilot system is implemented with a group project for the design of an electronic circuit (including both hardware and software designs). The functional assessment method is used to compare this platform to other collaborative design tools. The system presented offers unique qualitative advantages as an integrated collaboration support system.     

基于PLC的水泥生料配料控制系统研究

1 率值控制工艺结构 衡量生料质量的标准是水泥的三个率值．石灰石饱和系数KH、硅酸率SM、铝氧率IM，即在出磨生料中，、Fe2O3、Al2O3、SiO2诸氧化物的百分比含量必须满足以下二三式：     

Preparation of phenolic resin derived 3-D ordered macroporous carbon

Three-dimensionally ordered long-range macroporous carbon structures were prepared using commercially available phenolic resin by utilizing sacrificial colloidal silica crystalline arrays as templates that were subsequently removed by HF etching after pyrolysis in an argon atmosphere. SEM, TEM, and BET were employed to characterize the morphology and the surface area of the porous carbon structures. The pore size (150–1000 nm) and BET surface area, which reflect pore volume (298.6 m²/g (1.32 cm³/g) ∼ 93.7 m²/g (0.12 cm³/g)), of the macroporous carbon structures produced were approximately proportional to the size (150–1000 nm) of the sacrificial silica sphere templates used (annealing temp. 550°C). The achieved 550 nm porous carbon structures were examined to function as potential catalyst carriers and were successfully impregnated with Ag or Pt-Ru on their inner walls after borohydride reduction at room temperature. In addition, porous carbon patterns were fabricated using the ‘micromolding in capillary’ technique, which has potential applications in the microreaction technology.     

心理资本前因变量研究

采用心理资本问卷对分别属于医药、建筑、水利工程、电信、通讯运营和服务行业的6家企业的员工进行了调查.根据对回收的283份有效问卷的统计分析,认为员工的性别、受教育程度和所在企业的性质对员工心理资本不会产生显著性影响,而员工年龄的影响显著,50岁以上员工的总体心理资本水平高于其他年龄段员工.     

Fabrication and characterization of nano silver powder prepared by spray pyrolysis

Silver powder was fabricated by spray pyrolysis, using 2%–20% AgNO₃ solution, 336–500 mL/h flux of AgNO₃ solution, 0.28–0.32 MPa flux of carrier gas and in the 620–820 °C temperature range. The effects of furnace set temperature, concentration of AgNO₃ aqueous solution, flux of AgNO₃ aqueous solution as well as carrier gas on the morphology and particle size distribution of silver powder, were investigated. The experimental results showed that with the high concentration of AgNO₃ aqueous solution, the average grain size of silver decreased with the increasing of furnace set temperature. But the gain size distribution was not homogenous, the discontinuous grain growth occurred. With the low concentration of AgNO₃ aqueous solution, the higher furnace set temperature made the nano sliver grains sintered together to grow. Nano silver powder about 100 nm was fabricated by spray pyrolysis, using 2wt% AgNO₃ solutions, 336 mL/h flux of AgNO₃ aqueous solution, 0.32 MPa flux of carrier gas at 720 °C furnace set temperature.     

Zonal disintegration phenomenon in enclosing rock mass surrounding deep tunnels -- Elasto-plastic analysis of stress field of enclosing rock mass

The zonal disintegration phenomenon (ZDP) is a typical phenomenon in deep block rock masses. In order to investigate the mechanism of ZDP, an improved non-linear Hock-Brown strength criterion and a bi-linear constitutive model of rock mass were used to analyze the elasto-plastic stress field of the enclosing rock mass around a deep round tunnel. The radius of the plastic region and stress of the enclosing rock mass were obtained by introducing dimensionless parameters of radial distance. The results show that tunneling in deep rock mass causes a maximum stress zone to appear in the vicinity of the boundary of the elastic and the plas-tic zone in the surrounding rock mass. Under the compression of a large tangential force and a small radial force, the rock mass in the maximum stress zone was in an approximate uniaxial loading state, which could lead to a split failure in the rock mass.     

自激振荡脉冲射流的研究与进展

指出了自激振荡脉冲射流的产生机理,概述了国内外主要的研究和应用成果,并对这些成果进行分析后指出：目前的研究方法主要基于经验,基于理论或基于方法;目前主要的应用领域为石油钻井、油罐清淤和渔业充氧等.最后对进一步研究的方向和应用的领域作出了展望,可为相关研究参考.     

制备温度和压力对纳米氧化锆相组成的影响

利用压力[CD*2/3]热液法制备纳米氧化锆粉体,考察不同温度和压力下的制备工艺条件,以及采用XRD分析经过热处理后粉体的相组成和晶粒的长大倾向.结果表明,制备出的氧化锆粉体平均粒径约15 nm,粉体在600℃、800℃、1 000℃热处理1 h后,晶粒随温度长大趋势较小,抗老化能力较好.     

青县电子机箱产业集群核心竞争力评价

根据核心竞争力理论,运用层次分析法,构建了对产业集群的核心竞争力评价体系,并用此方法对青县的的电子机箱产业进行了实证分析.研究结果表明青县电子机箱行业的核心竞争力不强,其中资源整合与控制能力,技术创新能力、组织管理能力、人力资源竞争力和企业文化聚合力较弱、在此基础上提出了相应的政策建议.