Spray dryer processed graphene oxide/reduced graphene oxide for high-performance supercapacitor

This study deals with the utility of mini spray dryer process to improve the dispersibility, of graphene oxide(GO) and its application for high-performance supercapacitor. Initially, the neutral solution of GO was obtained using the modified Hummer's method. After this, the prepared GO solution was processed by mini spray dryer to obtain a more purified, lighter, and dispersed form of GO which is named as spray dryer processed GO (SPGO). The SPGO thus obtained showed excellent dispersibility behavior with various solvents, which is not found in case of conventional oven drying. Furthermore, utility of SPGO and its reduced form (r-SPGO) for supercapacitor applications have been investigated. Results obtained from the cyclic voltammetry(CV) analysis, impedance, and charge-discharge behavior of supercapacitor fabricated using r-SPGO shows enhanced features. Therefore, the simple spray dried GO and its reduced form, that is, r-SPGO can be utilized as a potential candidate for the supercapacitor application. Herein, as synthesized SPGO exhibited the specific capacitance of 12.07 and 37.6 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively, at a scan rate of 5 mV/s. On the other hand, reduced form of SPGO, that is, r-SPGO showed the specific capacitance of 27.16 and 230 F/g with PVA-H₃PO₄ and 1 mol/L H₃PO₄, respectively.     

An optimization study for preventing silica gelation and improving filtration effectiveness during pH reduction of high concentration silica solutions

The steam generation processes at the steam-assisted gravity drainage facilities result in huge quantities of wastewater streams, which are characterized by high pH and high silica levels. These concentrated streams need to be neutralized before their disposal via down-hole injection. The neutralization of these high-pH brines results in the formation of a gel-like substance, which makes it difficult to filter the amorphous silica gel. The wastewater used in this study was synthetically prepared using sodium metasilicate to mimic high-concentration silica solutions. Our experiments did not show any advantage of a two-step pH-neutralization process over the single-step process for suppressing silica gelation. A systematic experimental campaign was undertaken to investigate the effects of SiO₂ concentration, NaCl:SiO₂ ratio, and pH on the residual silica concentration, percent silica removal, filtration rate, and filtration effectiveness. For NaCl:SiO₂ ratios higher than 4.5, silica precipitation during pH reduction did not lead to the formation of gel or sol. The response surface methodology (RSM), based on the Doehlert design of experiments, was implemented to optimize the responses and provide high efficacy with fewer experiments. The results from the analysis of variance (ANOVA) analyses of the experimental data were used to evaluate the significance of each term in the quadratic model. 3D response surfaces and 2D contour plots were generated for determining the optimal ranges of independent factors for achieving the maximum silica removal, the highest filtration rate, the best filtration effectiveness, and the minimum residual silica concentration. An optimum operating region was established from the RSM analysis and overlay plot.     

pH-Responsive and Reversible A-Motif-Based DNA Hydrogel: Synthesis and Biosensing Application**

Functional DNA hydrogels with various motifs and functional groups require perfect sequence design to avoid cross-bonding interference with themselves or other structural sequences. This work reports an A-motif functional DNA hydrogel that does not require any sequence design. A-motif DNA is a noncanonical parallel DNA duplex structure containing homopolymeric deoxyadenosines (poly-dA) strands that undergo conformation changes from single strands at neutral pH to a parallel duplex DNA helix at acidic pH. Despite this and other advantages over other DNA motifs like no cross-bonding interference with other structural sequences, the A-motif has not been explored much. We successfully synthesized a DNA hydrogel by using an A-motif as a reversible handle to polymerize a DNA three-way junction. The A-motif hydrogel was initially characterized by electrophoretic mobility shift assay, and dynamic light scattering, which showed the formation of higher-order structures. Further, we used imaging techniques like atomic force microscopy and scanning electron microscope to validating its hydrogel like highly branched morphology. pH-induced conformation transformation from monomers to gel is quick and reversible, and was analysed for multiple acid-base cycles. The sol-to-gel transitions and gelation properties were further examined in rheological studies. The use of the A-motif hydrogel in the visual detection of pathogenic target nucleic acid sequence was demonstrated for the first time in a capillary assay. Moreover, pH-induced hydrogel formation was observed in situ as a layer over the mammalian cells. The proposed A-motif DNA scaffold has enormous potential in designing stimuli-responsive nanostructures that can be used for many biological applications.     

Microstructural Evolution in Liquid-Phase-Sintered SiC: Part III, Effect of Nitrogen-Gas Sintering Atmosphere

Effects of N₂ sintering atmosphere and the starting SiC powder on the microstructural evolution of liquid-phase-sintered (LPS) SiC were studied. It was found that, for the β-SiC starting powder case, there was complete suppression of the β→α phase transformation, which otherwise goes to completion in Ar atmosphere. It was also found that the microstructures were equiaxed and that the coarsening was severely retarded, which was in contrast with the Ar-atmosphere case. Chemical analyses of the specimens sintered in N₂ atmosphere revealed the presence of significant amounts of nitrogen, which was believed to reside mostly in the intergranular phase. It was argued that the presence of nitrogen in the LPS SiC helped stabilize the β-SiC phase, thereby preventing the β→α phase transformation and the attendant formation of elongated grains. To investigate the coarsening retardation, internal friction measurements were performed on LPS SiC specimens sintered in either Ar or N₂ atmosphere. For specimens sintered in N₂ atmosphere, a remarkable shift of the grain-boundary sliding relaxation peak toward higher temperatures and very high activation energy values were observed, possibly due to the incorporation of nitrogen into the structure of the intergranular liquid phase. The highly refractory and viscous nature of the intergranular phase was deemed responsible for retarding the solution–reprecipitation coarsening in these materials. Parallel experiments with specimens sintered using α-SiC starting powders further reinforce these arguments. Thus, processing of LPS SiC in N₂ atmosphere open the possibility of tailoring their microstructures for room-temperature mechanical properties and for making high-temperature materials that are highly resistant to coarsening and creep.     

Occurrence of wax esters and 1-O-alkyl-2,3-diacylglycerols in goat epididymal sperm plasma membrane

Two unusual lipid classes were detected by thin-layer chromatography in the neutral lipids derived from goat cauda-epididymal sperm plasma membrane. The lipids were identified as wax esters and 1-O-alkyl-2,3-diacylglycerols based on chromatographic properties, identity of their hydrolysis products, and infrared/¹H nuclear magnetic resonance spectral evidence. The membrane containedca. 3 and 5 μg/mg protein of wax esters and alkyldiacylglycerols, respectively. The relative proportions of wax esters and alkyldiacylglycerols in the total neutral lipids were 1.5% and 2.4%, respectively. The lipids contained fatty acids with chain lengths of C₁₄ to C₂₂. The major fatty acids of the wax esters were 14∶0, 16∶0, 16∶1ω7, 18∶0 and 18∶1ω9. The fatty acids in alkyldiacylglycerol were 16∶0, 18∶0, 22∶5ω3 and 22∶6ω3. Alkyldiacylglycerol was particularly rich in docosahexaenoic acid 22∶6ω3) representing 30% of the total fatty acids. The alcohols of wax ester were all saturated with C₂₀–C₂₉ carbon chains. The deacylated products derived from alkyldiacylglycerols were identified as hexadecyl, octadecyl and octadec-9′-enyl glycerol ethers.     

Microstructural Evolution in Liquid-Phase-Sintered SiC: Part I, Effect of Starting Powder

The effect of starting SiC powder (β-SiC or α-SiC), with simultaneous additions of Al₂O₃ and Y₂O₃, on the microstructural evolution of liquid-phase-sintered (LPS) SiC has been studied. When using α-SiC starting powder, the resulting microstructures contain hexagonal platelike α-SiC grains with an average aspect ratio of 1.4. This anisotropic coarsening is consistent with interface energy anisotropy in α-SiC. When using β-SiC starting powder, the β→α phase transformation induces additional anisotropy in the coarsening of platelike SiC grains. A strong correlation between the extent of β→α phase transformation, as determined using quantitative XRD analysis, and the average grain aspect ratio is observed, with the maximum average aspect ratio reaching 3.8. Based on these observations and additional SEM and TEM characterizations of the microstructures, a model for the growth of these high-aspect-ratio SiC grains is proposed.     

Transcritical CO2 Heat Pump Dryer: Part 2. Validation and Simulation Results

The simulation model of a transcritical CO₂ heat pump dryer presented in Part 1 has been first validated with available experimental data in this part and then used to simulate the heat pump dryer to study the variation of performance parameters such as heating COP, moisture extraction rate, and specific moisture extraction rate. The validation with experimental data shows that the model slightly over predicts the system performance. The possible reasons for the difference between experimental and numerical results are explained. Simulation results show the effect of key operating parameters such as bypass air ratio, re-circulation air ratio, dryer efficiency, ambient condition (temperature and relative humidity), and air mass flow rate. Results show that unlike bypass air ratio and ambient relative humidity, the effect of dryer efficiency, recirculation air ratio, ambient temperature, and air mass flow rate are very significant as far as the system performance is concerned.     

Effect of Repetitive Lysine-Tryptophan Motifs on the Eukaryotic Membrane

In a previous study, we synthesized a series of peptides containing simple sequence repeats, (KW)_n–NH₂ (n = 2,3,4 and 5) and determined their antimicrobial and hemolytic activities, as well as their mechanism of antimicrobial action. However, (KW)₅ showed undesirable cytotoxicity against RBC cells. In order to identify the mechanisms behind the hemolytic and cytotoxic activities of (KW)₅, we measured the ability of these peptides to induce aggregation of liposomes. In addition, their binding and permeation activities were assessed by Trp fluorescence, calcein leakage and circular dichrorism using artificial phospholipids that mimic eukaryotic liposomes, including phosphatidylcholine (PC), PC/sphingomyelin (SM) (2:1, w/w) and PC/cholesterol (CH) (2:1, w/w). Experiments confirmed that only (KW)₅ induced aggregation of all liposomes; it formed much larger aggregates with PC:CH (2:1, w/w) than with PC or PC:SM (2:1, w/w). Longer peptide (KW)₅, but not (KW)₃ or (KW)₄, strongly bound and partially inserted into PC:CH compared to PC or PC:SM (2:1, w/w). Calcein release experiments showed that (KW)₅ induced calcein leakage from the eukaryotic membrane. Greater calcein leakage was induced by (KW)₅ from PC:CH than from PC:SM (2:1, w/w) or PC, whereas (KW)₄ did not induce calcein leakage from any of the liposomes. Circular dichroism measurements indicated that (KW)₅ showed higher conformational transition compared to (KW)₄ due to peptide-liposome interactions. Taken together, our results suggest that (KW)₅ reasonably mediates the aggregation and permeabilization of eukaryotic membranes, which could in turn explain why (KW)₅ displays efficient hemolytic activity.     

PG-2, a Potent AMP against Pathogenic Microbial Strains,from Potato (Solanum tuberosum L cv. Gogu Valley) Tubers Not Cytotoxic against Human Cells

In an earlier study, we isolated potamin-1 (PT-1), a 5.6-kDa trypsin-chymotrypsin protease inhibitor, from the tubers of a potato strain (Solanum tuberosum L cv. Gogu Valley). We established that PT-1 strongly inhibits pathogenic microbial strains, but not human bacterial strains, and that its sequence shows 62% homology with a serine protease inhibitor. In the present study, we isolated an antifungal and antibacterial peptide with no cytotoxicity from tubers of the same potato strain. The peptide (peptide-G2, PG-2) was isolated using salt-extraction, ultrafiltration and reverse-phase high performance liquid chromatography (RP-HPLC). Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF/MS) showed the protein to have a molecular mass of 3228.5 Da, while automated Edman degradation showed the N-terminal sequence of PG-2 to be LVKDNPLDISPKQVQALCTDLVIRCMCCC-. PG-2 exhibited antimicrobial activity against Candida albicans, a human pathogenic yeast strain, and Clavibacter michiganensis subsp. michiganensis, a plant late blight strain. PG-2 also showed antibacterial activity against Staphylococcus aureus, but did not lyse human red blood cells and was thermostable. Overall, these results suggest PG-2 may be a good candidate to serve as a natural antimicrobial agent, agricultural pesticide and/or food additive.     

Multi Response Optimization on Machinability of SiC Waste Fillers Reinforced Polymer Matrix Composite Using Taguchi’s Coupled Grey Relational Analysis

Silicon - Recycling and reutilization of industrial waste is one way to minimize land pollution to attain green environment. In this research waste SiC grinding wheel was ball milled to powder form...