Neutron diffraction measurement was performed in-situ at high temperatures on Co-Re-Ta-C alloys with and without Cr addition. This included alloys containing different C content with the C/Ta ratio varying between 0.5 and 1.0. The Co-Re-solid solution matrix of the experimental alloys is polymorphic (like in pure cobalt) and transformed from low temperature hexagonal ? phase to high temperature cubic γ phase on heating. This transformation is reversible and show hysteresis. The main alloying addition, Re, stabilizes the ? Co-phase and increases the transformation temperature to above 1273 K. The onset of the \(\varepsilon \rightleftharpoons \gamma\) transformation during heating and cooling was found to differ depending on the alloy composition. In alloys without Cr addition the transformation was not completed on cooling and the high temperature γ phase was partly retained at room temperature in metastable state with the amount depending on the cooling rate from high temperature. The diffraction and microstructural results showed that Cr is ? stabilizer (similar as Re) but the role of Ta is not clear. The C/Ta ratio has no direct effect on the matrix phase transformation. Nevertheless, it influences indirectly by determining the amount of Ta which is freely available in the matrix. 相似文献
The selective wetting behavior of silica in emulsion styrene butadiene rubber (ESBR)/solution styrene butadiene rubber (SSBR) blends is characterized by the wetting concept, which is further developed for filled blends based on miscible rubbers. It is found that not only the chemical rubber–filler affinity but also the topology of the filler surface significantly influences the selective filler wetting in rubber blends. The nanopore structure of the silica surface has been recognized as the main reason for the difference in the wetting behavior of the branched ESBR molecules and linear SSBR molecules. However, the effect of nanopore structure becomes more significant in the presence of silane. It is discussed that the adsorption of silane on silica surface constricts the nanopore to some extent that hinders effectively the space filling of the nanopores by the branched ESBR molecules but not by the linear SSBR molecules. As a result, in silanized ESBR/SSBR blends the dominant wetting of silica surface by the tightly bonded layer of SSBR molecules causes a low‐energy dissipation in the rubber–filler interphase. That imparts the low rolling resistance to the blends similar to that of a silica‐filled SSBR compound, while the ESBR‐rich matrix warrants the good tensile behavior, i.e., good abrasion and wear resistance of the blends.
Grundwasser - Eine erfolgreiche biologische In-situ-Sanierung von PCE-kontaminierten Grundwasserleitern erfordert hinreichend reduzierende Bedingungen sowie die Anwesenheit von molekularem... 相似文献
Routine bridge inspections usually consist of visual observations. These inspections are time-consuming and subjective. There is a need to identify new inspection techniques for infrastructure that reduce traffic disturbance, and improve the efficiency and reliability of the acquired data. This study compared the performance of three different imaging technologies for the three-dimensional (3D) geometric modeling of existing structures: terrestrial laser scanning, close-range photogrammetry, and infrared scanning. Each technology was used to assess six existing concrete railway bridges. The technologies were compared in terms of geometric deviations, visualization capabilities, the level of the inspector’s experience, and degree of automation. The results suggest that all methods investigated can be used to create 3D models, however, with different level of completeness. Measurements such as span length, deck widths, etc. can be extracted with good accuracy. Although promising, a full off-site inspection is currently not feasible as some areas of the bridges were difficult to capture mainly due to restricted access and narrow spaces. Measurements based on terrestrial laser scanning were closer to the reality compared to photogrammetry and infrared scanning. The study indicates the no special training is needed for photogrammetry and infrared scanning to generate a 3D geometric model. 相似文献
Journal of Chemical Ecology - MACE is an open access collection of electron impact (EI) mass spectra for coupled gas chromatography-mass spectrometry (GC/MS) that serves as an add-on database,... 相似文献
Flowering plants often use chemical signals to attract their pollinators, and compounds that elicit attraction are known for several groups of pollinators. For other pollinators such as gall midges, however, compounds responsible for their attraction to flowers are largely unknown. Here, we describe the pollination biology of Anthurium acutangulum, a Neotropical aroid species found to be attractive to gall midges. We collected and analyzed its floral scent by dynamic headspace collections and gas chromatography coupled to mass spectrometry, and identified compounds responsible for pollinator attraction. The inflorescences were almost exclusively visited by gall midges (females; Cecidomyiidae: Cecidomyiinae) and released a strong scent reminiscent of freshly cut cucumber, mainly (5S,7S)-trans-conophthorin, (E2,Z6)-2,6-nonadienal, and cis-conophthorin. Behavioral assays with the two most abundant compounds identified (E2,Z6)-2,6-nonadienal as being highly attractive to the female gall midge pollinators, whereas (5S,7S)-trans-conophthorin was not attractive. Overall, we introduce a new specialized gall midge pollination system and identify the chemical mediating communication between the pollinators and their host plants.