Optimal Performance in Tracking Stochastic Signal Under Disturbance Rejection

The analysis method of optimal tracking performance is proposed for multiple‐input multiple‐output (MIMO) linear time‐invariant (LTI) systems under disturbance rejection. An H₂ criterion of the error signal between the output of the plant and the reference signal is used as a measure for the tracking performance. Spectral factorization is applied to obtain the optimal solution of the system tracking error. The explicit expressions are derived for this minimal tracking error with respect to random reference signals under disturbance rejection. It is shown that the nonminimum phase zeros, the zero direction, the unstable poles, the pole direction of a given plant, statistical characteristics of the reference input signal, and disturbance signal have a negative effect on a feedback system's ability to reduce the system error with disturbance rejection. The results show that the optimal tracking performance will further be damaged because of disturbance rejection. Some typical examples are given to illustrate the theoretical results.     

方柱体镦粗的两个新力学模型

在对平板间镦粗圆柱体的研究［１，２，３］基础上，进一步对普通平板间的方柱体镦粗，进行了工程力学的分析，提出了二个新力学模型，并进行了实验验证。这为形成新的拔长理论［４，６］奠定了力学基础。     

基于改进下垂控制的多微网并联运行控制策略研究

多微网并联的电网系统结构复杂、连接方式多样,在并网、解列的过程中由于子微网之间的频率和电压偏差,会在平衡点产生较大的电动力,对系统产生冲击,影响系统的动态稳定。本文针对多微网并网、解列过程中控制精度和动态稳定的问题,基于长距离线路电压降落和电压相角偏移,提出了一种改进的下垂控制方法,减少了系统的电压震荡和频率波动。最后基于Matlab/Simulink建立仿真模型,仿真结果验证了改进控制策略的合理性和有效性。     

侧向土体影响下盾构隧道引起上覆管线变形

目前盾构隧道开挖对邻近管线影响的理论研究一般基于Winkler地基模型和Pasternak地基模型,较少考虑精度更高的Kerr地基模型及管线侧向土体影响对管线变形的约束作用. 将管线简化成Euler-Bernoulli梁搁置在Kerr地基模型上,利用差分法得到盾构隧道引起上覆管线竖向位移半解析解,在此基础上进一步推导考虑管线侧向土体影响的Kerr地基模型差分解. 通过与已有工程案例和离心机数据对比,验证Kerr地基模型相比于其他地基模型的优越性,也验证了考虑管线侧向土体影响的Kerr地基模型计算结果更加符合实测数据. 参数分析表明, 随着隧道开挖地层损失率和土体弹性模量的增大,管线的竖向位移和弯矩均增大;随着管线与隧道夹角的增大,管线的竖向位移和弯矩均减小.     

Crystallographic structure- and texture-dependent fracture behavior of polycrystalline lead zirconate titanate ceramics

Journal of Electroceramics - The effect of crystallographic structure and texture on the fracture behavior of lead zirconate titanate (PZT) ceramics was investigated. PZT ceramics with Zr/Ti ratio...     

焊接热源有效利用率的测试计算法

给出实际热输入值是正确求解焊接热弹塑性问题和焊接残余应力与变形问题的前提;因而,准确地确定热源有效利用率η,在焊接力学的发展中是一个急待解决的命题。本文推荐采用的“测试计算法”提供了一个能够准确、简捷地求得η值的新途径。引入被焊材料的熔化潜热系数后,给出了线热源加热焊缝金属至熔化温度(处于液态)时的实际热有效利用率ηt 的表达式。在四种不同类型的薄板材料上进行了钨极氩弧焊试验,测试计算结果与理论值相符合。理论推导与试验结果均证明,形成焊缝所需要的线能量的无量纲数值等于焊缝金属熔化热有效利用率ηt 的倒数。文中给出的焊接规范参数选择原则也适用于符合线热源条件的其它熔焊热源。η值不但与焊接工艺方法、规范参数有关,而且也随被焊材料的热物理特性不同而异。     

基于粒子群算法的移动机器人全局最优路径规划*

以栅格法和粒子群算法为基础,提出了一种新的机器人实时全局最优路径规划方法.该方法包括采用栅格法对环境进行建模和直接运用粒子群算法在环境模型中搜索全局最优路径.在计算机上进行了仿真,仿真结果证明了该方法的可行性和有效性.     

Correction to: Bismuth Yttrium Oxide (Bi3YO6), A New Electrode Material For Asymmetric Aqueous Supercapacitors

Journal of Inorganic and Organometallic Polymers and Materials - The original version of this article unfortunately contained mistakes. In line 9 of the abstract, 5% should read as 2%. The...     

Design and Achievement of Metallurgical Bonding of Mg/Al Interface Prepared by Liquid–Liquid Compound Casting via a Co-deposited Cu–Ni Alloy Coating

The metallurgical bonding of Mg/Al bimetal by liquid–liquid compound casting was realized via co-deposition Cu–Ni alloy coating. The metallurgical layer of the Mg/Al bimetal consisted of Cu solid solution, Cu₂Mg and (Al0.7Cu1.3) Mg, Mg solid solution, Al₃Ni₂, and Mg₂Cu. Vickers hardness of the interface was between 149.9 and 209 HV, which was significantly lower than those of Al–Mg intermetallic compounds. The formation mechanism of the interface was attributed to interdiffusion among AZ91D, A356, and Cu–Ni alloy coating.

     

硬脆材料专用ELID磨削液的研制

本文在已有新型通用ELID磨削液(HDMY-20型)的基础上，根据硬脆材料的磨削特点和ELID磨削过程中磨削液的电解修锐生膜缓蚀作用、结合通用ELID磨削液的研制经验．通过增添表面活性剂、稳定剂、防锈剂、油性极压剂和调整无机盐等成分的比例关系．优化出适合硬脆材料ELID磨削最佳状态的专用ELID磨削液。应用此磨削液磨削硬质合金表面粗糙度可达Ra0．007μm比通用型磨削液磨削的硬质合金Ra值降低了0．005μm。