Electrical behaviour of discontinuous silver films deposited on softened polystyrene and poly (4-vinylpyridine) blends

Results of the studies carried out on the electrical behaviour of silver island films deposited on the blends of polystyrene (PS) and poly (4-vinylpyridine) (P4VP) are presented here. The substrates were held at 457 K, much above the glass transition temperature of both the polymers to ensure sufficient polymer fluidity during deposition, to obtain a sub-surface particulate film. A constant deposition rate of 0.4 nm/s was used throughout the study. Films on softened PS gives rise to a very high room temperature resistance approaching that of the substrate resistance due to the formation of a highly agglomerated structure. On the other hand, films on softened P4VP gives rise to a room temperature resistance in the range of a few tens to a few hundred MΩ/, which is desirable for device applications. The blends of PS and P4VP show room temperature resistances in the desirable range even at a PS/P4VP ratio of 75:25. The films show an increase in resistance when they are exposed to atmosphere. This is attributed to the oxidation of silver islands. The film resistances in the desired range could be obtained even after exposure to atmosphere up to a PS concentration of 50%.     

Flexible Hardware Acceleration for Instruction-Grain Lifeguards

Instruction-grain lifeguards monitor executing programs at the granularity of individual instructions to quickly detect bugs and security attacks, but their fine-grain nature incurs high monitoring overheads. This article identifies three common sources of these overheads and proposes three techniques that together constitute a general-purpose hardware acceleration framework for lifeguards.     

Erosion of atmospheric plasma sprayed rare earth oxide coatings under air suspended corundum particles

Atmospheric plasma sprayed (APS) zirconium oxide based coatings are used widely in aero engine components for providing thermal insulation, improving the corrosion and oxidation resistance. Despite its wide spread industrial use, little is known about the basic erosion behaviour and the mechanisms by which such coatings erode. In this paper, the erosive wear behaviours of Yttria Stabilized Zirconia (YSZ) coatings; Lanthanum Zirconate (LZ) coatings and Inconel 738 base material (BM) were studied and compared under air jet erosion conditions with corundum particles as erodent material. The erosion behaviour was studied with respect to the different porosity volume percentages of the coatings and the changes in velocity of erodent, impact angle of erodent and erodent particle flux. It was found that in solid particle erosion, the wear resistances of YSZ and LZ coatings were the best at their lowest porosity volume and it decreased with the increase in the percentage volume of porosity. There was a linear increase in the wear resistance with the increase in hardness. Further, relationships among the erosion parameters with respect to erosive wear loss were derived by using the response surface methodology and the erosion mechanisms were discussed adequately.     

Exploring the Influence of Methylene Diphenyl Diisocyanate as a Modifier for Ethylene Vinyl Acetate/Thermoplastic Polyurethane Blends

Ethylene vinyl acetate (EVA)/thermoplastic polyurethane (TPU) blend at various blend ratios has been modified via reactive processing with 4,4′-methylene diphenyl diisocyanate (MDI). Modification of the blends with even small amount of MDI shows significant improvement in physico-mechanical properties for EVA/TPU 50/50 and 30/70 blends, and it is also supported by the superior melt rheological behavior and dramatic improvement in oil resistance property. After the treatment of electron beam (dose range: 50–150?kGy), radiation crosslinked EVA/TPU (30:70) blend reveals further improvement in various properties. This particular material can find potential application as cable sheathing component.     

Asiatic acid prevents lipid peroxidation and improves antioxidant status in rats with streptozotocin-induced diabetes

Oxidative stress is a common pathogenesis of diabetes mellitus and asiatic acid (AA) plays an important role in ameliorating those difficulties. The present study was designed the protective effects of AA on altered lipid peroxidation products, enzymic and nonenzymic antioxidants in streptozotocin (STZ)-induced diabetic rats. Diabetes was induced in experimental rats by single dose STZ (40 mg/kg b.w.) injection. Diabetic rats showed significantly increased levels of plasma glucose, thiobarbituric acid reactive substances, lipid hydroperoxides, aspartate aminotransferase, alanine aminotransferase, bilirubin, creatine kinase, urea, uric acid, creatinine and decreased levels of plasma insulin. The activities of enzymatic antioxidants such as superoxide dismutase, catalase, glutathione peroxidase and glutathione-S-transferase and the levels of non-enzymatic antioxidants such as vitamin C, vitamin E and reduced glutathione were decreased in diabetic rats. Oral treatment with AA (20 mg/kg b.w.) showed near normalized levels of plasma glucose, insulin, lipid peroxidation products, enzymatic and nonenzymatic markers in diabetic rats. The results demonstrate that AA possesses potent antioxidant effect comparable with glibenclamide in improving antihyperglycemia and attenuating antioxidant status in diabetic rats.     

Characterization of Morphological Changes in Agglomerates Subject to Condensation and Evaporation Using Multiple Fractal Dimensions

Multiple fractal dimensions are used to characterize morphological changes that occur when an aerosol composed of irregularly shaped agglomerates is subject to condensation followed by evaporation. The agglomerates change from a branched, chainlike structure to a more regular, near-spherical or clumplike structure reflected in a decrease in the structural fractal dimension. The textural fractal dimension remains constant because the primary particles, of which the agglomerates are composed, do not change in shape. The degree of supersaturation and the number of condensation-evaporation cycles that the aerosol undergoes are major factors that influence morphological change. Even at low supersaturations, increasing the number of condensation-evaporation cycles makes the agglomerates more regular and thus decreases the structural fractal dimension. The transition point in the Richardson plot is a good indicator of the size of the primary particles in the agglomerate.     

Effect of channel geometry on solute dispersion in pressure-driven microfluidic systems

Pressure-driven transport of fluid and solute samples is often desirable in microfluidic devices, particularly where sufficient electroosmotic flow rates cannot be realized or the use of an electric field is restricted. Unfortunately, this mode of actuation also leads to hydrodynamic dispersion due to the inherent fluid shear in the system. While such dispersivity is known to scale with the square of the Peclet number based on the narrower dimension of the conduit (often the channel depth), the proportionality constant can vary significantly depending on its actual cross section. In this article, we review previous studies to understand the effect of commonly microfabricated channel cross sections on the Taylor–Aris dispersion of solute slugs in simple pressure-driven flow systems. We also analyze some recently proposed optimum designs which can reduce the contribution to this band broadening arising from the presence of the channel sidewalls. Finally, new simulation results have been presented in the last section of this paper which describe solutal spreading due to bowing of microchannels that can occur from stresses developed during their fabrication or operation under high-pressure conditions.     

UbiqStack: a taxonomy for a ubiquitous computing software stack

This paper describes a taxonomy for a ubiquitous computing software stack called UbiqStack. Through the lens of the UbiqStack taxonomy we survey a variety of subsystems designed to be the building blocks from which sophisticated infrastructures for ubiquitous computing are assembled. Our experience shows that many of these building blocks fit neatly into one of the five UbiqStack categories, each containing functionally-equivalent components. Effectively identifying the best-fit “Lego pieces”, which in turn determines the composite functionality of the resulting infrastructure, is critical. The selection process, however, is impeded by the lack of convention for labeling these classes of building blocks. The lack of clarity with respect to what ready-made subsystems are available within each class often results in naive re-implementation of ready-made components, monolithic and clumsy implementations, and implementations that impose non-standard interfaces onto the applications above. This paper describes the UbiqStack classes of subsystems and explores each in light of the experience gained over 2 years of active development of both ubiquitous computing applications and software infrastructures for their deployment.     

Rheological characterization of hydroxypropylcellulose gels

The present paper describes the rheological properties of hydroxypropylcellulose (HPC) gels formulated in propylene glycol (PG), water, ethanol, and mixtures of these components. The effects of molecular weight, polymer concentration, and solvent composition on the apparent viscosity and flow characteristics have been studied by continuous shear rheometry. The HPC gels are shear thinning and do not exhibit significant yield or hysteresis in their rheograms. The apparent viscosity increases with increasing molecular weight and concentration of the polymer, as expected. Although not so pronounced at lower concentrations (≤ 1.5%), HPC gels tend to become increasingly non-Newtonian with increasing molecular weight at higher polymer concentrations (3%). A mathematical model has been proposed for the prediction of viscosities of HPC gels. There exists a high degree of dependence on molecular interactions between various solvent molecules in the prediction of mixture viscosities in ternary systems. The effects of solvent composition on the viscoelastic behavior of these gels have also been examined by dynamic mechanical analysis. The HPC gels are highly viscoelastic and exhibit greater degrees of elasticity with increased PG content in ternary solvent mixtures with water and ethanol. The study also suggests that dynamic mechanical analysis could prove to be a useful tool in the determination of zero-shear viscosities, viscosities that are representative of most realistic situations.     

The specificity of the N-terminal SH2 domain of SHP-2 is modified by a single point mutation

SH2 domains are small protein domains of approximately 100 amino acids that bind to phosphotyrosine (pY) in the context of a specific sequence surrounding the target pY. In general, the residues C-terminal to the pY of the binding target are considered most important for defining the binding specificity, and in particular the pY + 1 and pY + 3 residues (i.e., the first and third amino acids C-terminal to the pY). However, our previous studies with the SH2 domains of the protein tyrosine phosphatase SHP-2 [Huyer, G., Li, Z. M., Adam, M., Huckle, W. R., and Ramachandran, C. (1995) Biochemistry 34, 1040-1049] indicated important interactions with the pY - 2 residue as well. In the SH2 domains of SHP-2, the highly conserved alphaA2 Arg is replaced by Gly. A comparison of the published crystal structures of the Src SH2 domain and the N-terminal SH2 domain of SHP-2 complexed with high-affinity peptides suggested that the alphaA2 Gly of SHP-2 creates a gap which is filled by the side chain of the pY - 2 residue of the bound peptide. It was predicted that replacing this Gly with Arg would alter or eliminate the involvement of the pY - 2 residue in binding. The alphaA2 Gly --> Arg mutant was constructed, and indeed, this mutant no longer required residues N-terminal to the target pY for high-affinity binding, making its specificity more like that of other SH2 domains. The alphaA2 Gly is clearly involved in directing the unusual requirement for the pY - 2 residue in the binding sequence of this SH2 domain, which has important implications for its in vivo targeting and specificity.