Signal tracking method of GNSS receivers for spinning vehicles

A signal tracking method of GNSS receivers for spinning vehicles is proposed in order to eliminate the influence of spinning to the GNSS signal of a vehicle. In the proposed method, a rotation tracking loop is added into the carrier tracking loop of a conventional GNSS receiver. The proposed method was verified through computer simulations and an experiment for live GPS signals. The results show that the proposed method gives an accurate tracking performance.     

The α- to β-Si3N4 transformation in the presence of liquid silicon

The compacts consisted of , -Si₃N₄ and free silicon are heat treated in the range 1650° C to 1750° C in an argon atmosphere in order to observe the following behaviours; the to phase transformation and variations of the microstructure during heat treatment in silicon nitride. For the microstructural observation of the heat treated specimens, the same grains in the polished surface were investigated before and after eliminating the retained silicon by etching. The to phase transformation, in this case, occurs via silicon melts irrespective of added -Si₃N₄. Both and phases are soluted and precipitated into molten silicon and their morphology are changed from an equiaxed shape to prismatic one. Although elongated grains are precipitated at low temperature or in the early stage of heat treatment, fine precipitated grains are mainly observed with increasing heat treating temperature.     

In-Plane Cracking Behavior and Ultimate Strength for 2D Woven and Braided Melt-Infiltrated SiC/SiC Composites Tensile Loaded in Off-Axis Fiber Directions

The tensile mechanical properties of ceramic matrix composites (CMC) in directions off the primary axes of the reinforcing fibers are important for the architectural design of CMC components that are subjected to multiaxial stress states. In this study, two-dimensional (2D)-woven melt-infiltrated (MI) SiC/SiC composite panels with balanced fiber content in the 0° and 90° directions were tensile loaded in-plane in the 0° direction and at 45° to this direction. In addition, a 2D triaxially braided MI SiC/SiC composite panel with a higher fiber content in the ±67° bias directions compared with the axial direction was tensile loaded perpendicular to the axial direction tows (i.e., 23° from the bias fibers). Stress–strain behavior, acoustic emission, and optical microscopy were used to quantify stress-dependent matrix cracking and ultimate strength in the panels. It was observed that both off-axis-loaded panels displayed higher composite onset stresses for through-thickness matrix cracking than the 2D-woven 0/90 panels loaded in the primary 0° direction. These improvements for off-axis cracking strength can in part be attributed to higher effective fiber fractions in the loading direction, which in turn reduces internal stresses on weak regions in the architecture, e.g., minicomposite tows oriented normal to the loading direction and/or critical flaws in the matrix for a given composite stress. Both off-axis-oriented panels also showed relatively good ultimate tensile strength when compared with other off-axis-oriented composites in the literature, both on an absolute strength basis as well as when normalized by the average fiber strength within the composites. Initial implications are discussed for constituent and architecture design to improve the directional cracking of SiC/SiC CMC components with MI matrices.     

Effects of Y2O3 and ZrO2 on the Densification of Si3N4-Zr(Y)O2 Composites

The effects of ZrO₂ and Y₂O₃ on the densification of hotpressed Si₃N₄-Zr(Y)O₂ composites have been studied. High density could not be obtained by the addition of pure or 3-mol%-Y₂O₃-doped ZrO₂ in this composite; however, nearly full density (>97%) could be obtained in Si₃N₄ using 6- and 8-mol%-Y₂O₃-doped ZrO₂. It is concluded that Y₂O₃ diffusing out from the added Zr(Y)O₂ promoted the densification and that ZrO₂ also had some role in the formation of an oxynitride glass.     

Effect of adsorptive gaseous reactant on non-isothermal behavior for gas-solid reactions

The effect of adsorptive species on non-isothermal gas-solid reactions is studied on the basis of Langmuir-Hinshelwood kinetics. The concept of an effectiveness factor provides good information to ascertain the effect of adsorptive species and the transition of the rate controlling regime, in connection with the parameters, generally used in the analysis of non-isothermal behavior. For highly exothermic reactions, the effectiveness factor-Thiele modulus curves with multiple solutions are presented with respect to the modified adsorption equilibrium constant. The variations of the rate-controlling regime by the effect of adsorptive species are also discussed.     

A new characterization procedure for aqufous solutions with unknown composition

A new characterization procedure for aqueous solutions with unknown composition was proposed based on the binomial distribution of TOC (total organic carbon) fraction in terms of a characterizing variable, the Freundlich coefficient, k, so that the solution in question can be described by a finite number of pseudo.species identified with a certain k value. The validity and computational accuracy of this procedure has been demonstrated by characterizing three sets of experimental data chosen from different sources. Predictions based on this procedure yielded acceptable results that agreed closely with experimental data.     

Diffusional interference in liquid phase counter-adsorptions

A surface diffusion mocel with diffusional interference has been presented for the analysis of multicomponent adsorption of phenols by activated carbon. Surface diffusion coefficients for multicomponent adsorptions were estimated from the relationship between. the surface diffusion coefficient of each species and the surface coverage. The diffusional interference coefficients, W_ij, was determined from experimental counter-adsorption data. The numerical values of W_ij were in the range of 0.4–0.9, which show that the introduction of diffusional interference is necessary to analyze multicomponent counter-adsorptions properly. The proposed model successfully simulates the behaviour of phenols-activated carbon system in a batch adsorber.     

A study on the factors for improving the ethanol production from Jerusalem artichoke by Kluyveromyces fragilis

This study is to investigate the factors influencing the alcohol production byKluyveromyces fragilis using the juice of Jerusalem Artichoke tubers. The cell growth rate and ethanol production rate were stimulated by aeration and by the addition of unsaturated fatty acids and the cell mass production and the ethanol production were substantially improved. It was found that oxygen and unsaturated fatty acids added played a decisive role on the increase of alcohol tolerance of yeast.     

Companion robots for older adults: Rodgers’ evolutionary concept analysis approach

Intelligent Service Robotics - This study aims to analyze the concept of companion robots for older adults from the perspective of nursing. This study employed a concept analysis. The literature...