Fuzzy logic switching of thyristor controlled braking resistorconsidering coordination with SVC

This paper presents a new switching control scheme for braking resistors (BR) using fuzzy logic to enhance overall stability of electric power systems. In addition, the coordination with an SVC is also considered to achieve a wider stable region. The braking resistor is set on one of the generator busbars, where the real power output from the generator is measured to determine the firing-angle of the thyristor switch. The switching control scheme is simple so as not to require heavy computation on the microcomputer based switching controller. An SVC is set on one of the busbars in the system. The switching of the SVC uses a similar fuzzy logic control scheme to the one for the BR. Simulation results show the effectiveness of the proposed fuzzy logic switching control scheme     

Transcutaneous measurement and spectrum analysis of heart wallvibrations

For the noninvasive diagnosis of heart disease based on the acoustic and elastic characteristics of the heart muscle, it is necessary to transcutaneously measure small vibration signals, including components with an amplitude of less than 100 μm, from various parts of the heart wall continuously for periods of more than several heartbeats in a wide frequency range up to 1 kHz. Such measurement, however, has not been realized by any ultrasonic diagnostic methods or systems to date. By introducing the constraint least-square approach, this paper proposes a new method for accurately tracking the movement of the heart wall based on both the phase and magnitude of the demodulated signal to determine the instantaneous position of the object so that the vibration velocity of the moving object can be accurately estimated. By this method, small vibrations of the heart wall with small amplitudes less than 100 μm on the motion resulting from a heartbeat with large amplitude of 10 mm can be successfully detected with sufficient reproducibility in the frequency range up to several hundred Hertz continuously for periods of about 10 heartbeats. The resultant small vibration is analyzed not only in the time domain, but also in the frequency domain. As confirmed by the preliminary experiments herein reported, the new method offers potential for research in acoustical diagnosis of heart disease     

Some factors affecting the electrical properties of carbon-black-loaded butyl rubber during vulcanization

Butyl rubber mixtures loaded with 70 phr general purpose furnace black (GPF) and tetramethyl thiuram disulphide (TMTD)/S as vulcanizing system were prepared. The kinetics of their electrical conductivity development during the vulcanization process were followed by using an especially devised system. It was found that the increase in the electrical conductivity during vulcanization obeys an exponential growth function with time constant τ, which markedly decreases with increasing vulcanization temperature as well as with the efficiency of the vulcanizing system. After completion of the vulcanization process, about 80 min, the samples obtained possess reasonable stability and reproducibility of electrical conductivity.     

Creating and Justifying Research and Development Value: Scope,Scale, Skill and Social Networking of R&D

In this paper we describe a framework for analysing the creation and justification of Research & Development. The 4S framework is developed for analysing the scope, scale, skills and social network aspects of Research & Development value. The framework is based on social system theory, a process contingency model, and recent Research & Development metrics. We present a first empirical assessment based on a workshop using the 4S framework for leveraging Research & Development. Results that assist in the assessment of value creation utilising R & D within networks are very relevant in high tech industries. The multi–dimensional process approach of this framework seems promising for understanding and managing R&D value creation, but needs further operationalisation. Case studies are described and a Dutch network on leveraging R&D has been initiated.     

Object-oriented H.263 compatible video coding platform forconferencing applications

This paper describes a prototype video coding platform meant for the conception and testing of multimedia products such as next-generation videophones. The platform is largely based on ITU-T Recommendation H.263, with a number of additional object-oriented quality enhancement features which make it especially well suited for very low bit-rate coding of “head-and-shoulders” video material typical of real-time multimedia applications, video teleconferencing, and video telephony. These features consist of: (1) segmentation into objects of interest, (2) segmentation-based prefiltering, (3) model-assisted rate control, (4) adaptive vector quantization, and finally (5) segmentation-based postfiltering. In the spirit of Recommendation H.263, these enhancements are modular and can be selectively turned on or off, thereby enabling a wide variety of coding modes     

Diarrhea in young children associated with Escherichia coli non-O157 organisms that produce Shiga-like toxin

The aim of this study was to evaluate the way in which short-term protection declines and is eventually lost in preconditioning and to determine the efficacy of a second preconditioning at various reperfusion intervals. Male rabbits were divided into six groups. Forty-five minutes (sustained) ischemia followed by 120 minutes reperfusion was applied 60, 65, 70, 75, and 80 minutes after a 5 minute preconditioning (groups A, B, C, D, and E) and in a control group (F) after no preconditioning. The infarct to risk ratio (I/R) was 38.3 +/- 3.5% in group A, 46.0 +/- 7.8% in B, 61.6 +/- 9.7% in C, 68.1 +/- 4.2% in D, 64.5 +/- 7.8% in E, and 61.0 +/- 7.7% in F. Group A had a smaller I/R compared with groups C, D, E, and F (p < 0.05). In another series, groups G, H, and I were exposed to two 5-minute preconditioning stimuli, separated, respectively, by 45, 60, and 75 minutes of reperfusion; 10 minutes after the last preconditioning, the animals were exposed to 45-minutes ischemia and 120 minutes reperfusion. Groups A and D (with the smaller and higher I/R ratio) were also incorporated into this protocol in order to compare the effect of the additional preconditioning with the single one. The I/R ratio was 25.4 +/- 8.5% in group G, 22.8 +/- 7.0% in group H, and 14.7 +/- 4.0% in group I (p = NS). Group D showed a higher I/R compared with groups G, A, and H (p < 0.01), and group I had a smaller I/R compared with groups A (p < 0.01) and D (p < 0.001). Cardioprotection after a first preconditioning declines gradually and is eventually lost. An additional preconditioning is always effective, and the longer the interval from the first preconditioning, the more potent is the effect.     

Neurocontrol for lateral vehicle guidance

A solution to autonomous lateral vehicle guidance using a neurocontroller that can learn from measured human-driving data without knowledge of the physical car parameters is discussed. Simulations and practical tests confirm that a small-size feedforward autonomous neural network (21 neurons) can learn to steer a vehicle at high speeds only from looking at human-driving examples. In this way, the network learns the total closed-loop behavior, including the nonlinear dynamics of the vehicle and the driver's individual driving style. The main result of practical investigations is that the neutral controller trained on human-driving examples exhibits an aperiodic behavior that does not vanish at higher speeds (tests performed up to 130 km/h) and produces fewer lateral deviations than the linear state controller     

Effects of forced power transfer on high speed generator-loadsystems

A computer-aided method for investigating disturbances due to the forced paralleling of out of phase high speed salient pole AC generator systems feeding isolated loads is presented. The method is used to predict the system performance including the reverse voltage across the rotating bridge rectifier of the field exciter. This paper presents the fundamentals and the modeling approach used in the development of this method. In addition, the results of using this approach to compute the machine parameters under different load conditions including saturation effects due to magnetic material nonlinearities and space harmonics effects due to machine geometry and winding layouts are presented. The computed parameters are validated by comparison to test data. These parameters form the main data for simulating the forced paralleling of out of phase high speed salient pole AC generator systems feeding isolated loads. Further, the results of using this modeling approach in a case study to predict the system performance due to forced power transfer are summarized and are shown to be in good agreement with test data     

Vessel wall detection and blood noise reduction in intravascularultrasound imaging

Scattering from blood limits the contrast between the vessel wall and the lumen in intravascular ultrasound imaging. This makes it difficult to localize the vessel wall, especially on still images. This paper presents a method for automatic detection of vessel walls and reduction of blood noise based on correlation of the RF-signal between adjacent frames. The ultrasound RF-signal is quadrature demodulated, digitized, stored in memory, and transferred to a computer for processing and analysis. The absolute value of the cross-correlation coefficient between two adjacent frames is used to differentiate between stationary and fluctuating signals. Models and numerical calculations presented in this work indicate that the cross-correlation coefficient obtained from a radially dilating vessel wall will be larger than 0.8 under standard 20 MHz imaging conditions. The corresponding value from blood is less than 0.2 for blood velocities exceeding 0.5 cm s^-1 . The blood-noise filter is based on detecting this difference in correlation and displays vessel wall regions with no modifications, while regions detected as blood are rejected. A simplified vessel-wall detector that is suitable for real-time implementation is proposed. The performance of this detector and the blood noise filter are demonstrated by in vitro experiments     

Instron texture profile of buffalo milk cheddar cheese as influenced by composition and ripening changes

Buffalo milk Cheddar cheese samples of different ages were analysed for compositional attributes (CA), ripening indices (RI) and Instron Textural Profile (ITP). All samples were compositionally alike, except for pH and salt-in-moisture (SM) contents. RI showed significant variations. CA and RI showed highly significant correlations within themselves and with each other, except for moisture with pH, SM with moisture, MNFS, Fat and FDM and Fat with MNFS. The ITPs of cheeses showed significant variations and had highly significant intercorrelations indicating their interdependence. CA (except moisture and MNFS) and RI showed a highly significant correlationship with ITPs. Moisture content showed a highly significant correlationship with all ITPs, except cohesiveness and springiness, where it was significant. MNFS content showed significant correlations only with hardness and brittleness. Stepwise regression analysis revealed that MI was the most predominant factor influencing cheese texture, followed by pH, SM, FDM and TVFA. Knowing Ca and RI, the textural properties of cheeses can be forecast through mathematical equations. Similarly the age of cheese can also be predicted if RI and/or textural properties are known.