Boosting nitrification by membrane-attached biofilm.

Nitrification is a key step for reliable biological nitrogen removal. In order to enhance nitrification in the activated sludge (AS) process, membrane-attached biofilm (MAB) was incorporated in a conventional activated sludge tank. Simultaneous organic carbon removal and nitrification of the MAB incorporated activated sludge (AS + MAB) process was investigated with continuous wastewater treatment. The effluent TOC concentration of AS and the AS + MAB processes were about 6.3 mg/L and 7.9 mg/L, respectively. The TOC removal efficiency of both AS and AS + MAB were above 95% during the wastewater treatment, indicating excellent organic carbon removal performance in both processes. Little nitrification occurred in the AS process. On the contrary, successful nitrification was obtained with the AS + MAB process with nitrification efficiency of about 90%. The volumetric and surface nitrification rates were about 0.14 g/Ld and 6.5 g/m2d, respectively. The results clearly demonstrated that nitrification in the conventional AS process was boosted by MAB. Furthermore, the microfaunal population in the AS + MAB process was different from that in the AS process. The high concentration of rotifers in the AS + MAB process was expected to decrease the generation of excess sludge in the process.     

Effect of grain boundaries on isothermal solidification during transient liquid phase brazing

The influence of liquid penetration at grain boundary regions on the rate of advance of the solid-liquid interface during isothermal solidification of transient liquid phase (TLP) brazed nickel joints has been examined. The test samples used in this study were Ohno-cast nickel with a grain size of >4 mm and a fine-grained nickel with a grain size of around 40 μm. Both Ni-base materials had the same chemical composition. The rate of isothermal solidification was greater when fine-grained nickel was employed during TLP brazing using Ni-11 wt pct P filler metal at 1200 °C. Liquid penetration at grain boundaries accelerates the isothermal solidification process by increasing the effective solid-liquid interfacial area and increasing the rate of solute diffusion into the base material. An analysis of electron channeling patterns has confirmed that random high-angle boundaries have a greater influence on the rate of isothermal solidification than ordered boundaries including small-angle or twin boundaries. Formerly Visiting Scientist, Department of Metallurgy and Materials Science, University of Toronto. Formerly Postdoctoral Fellow, Department of Metallurgy and Materials Science, University of Toronto     

Kinematic nonuniqueness of elastoplastic structures

Lack of uniqueness of the kinematic solution of structures, analyzed as an assemblage of discretized elements assuming nonholonomic linearly-elastic/perfectly-plastic behaviour and a linearized yield surface, is studied. The occurrence of an elastoplastic mechanism leads to nonuniqueness; an elastoplastic mechanism is defined as a kinematically-admissible strain rate field made up of an admissible elastoplastic solution of the governing conditions and an add-on variable component consisting of a linear combination of plastic (collapse) mechanisms. The scalar multipliers of this linear combination are bounded, except at plastic collapse in which case the elastoplastic mechanism degenerates to a plastic mechanism. In the space of loads, the load paths that could coexist with nonuniqueness are restricted to a hyperplane or a crease of intersection of hyperplanes, defined by the equilibrium equations arising from the associated plastic mechanisms of the elastoplastic mechanism. The difference between any two competing displacement vectors would be normal to that hyperplane or crease, in the same manner plastic strain rates are to the yield surface according to the flow rule.     

Comfort limits for asymmetric thermal radiation

Groups of 32 and 16 subjects of both sexes were exposed in an environmental chamber to radiant asymmetry caused by a cool wall, a warm wall, and a cool ceiling. Each subject was tested individually while seated and clothed at 0.6 clo. During each 3.5-hour experiment the subject was exposed to six radiant temperature asymmetries. He was asked whether and where he experienced any local cool or warm sensation, and whether it was felt to be uncomfortable. During the entire experiment he was kept thermally neutral by changing the air temperature according to his wishes.For cool walls, warm walls, and cool ceilings curves have been established showing the percentage of dissatisfied subjects as a function of the radiant asymmetry. Radiant asymmetry at a warm wall caused less discomfort than a cool wall. A cool ceiling caused less discomfort than a warm ceiling. Accepting that 5% of the subjects may feel uncomfortable. a radiant temperature asymmetry of 10°C is allowable at a cool wall, 23°C at a warm wall, and 14°C under a cool ceiling. A previous study showed that 4°C is allowable under a warm ceiling. Radiant asymmetry had no significant impact on the operative temperatures preferred by the subjects. No significant differences were observed between the responses of men and women exposed to radiant asymmetry.     

Hydrologic regionalisation impacts on wet-weather control selection.

Continuous simulation is performed using the US Environmental Protection Agency (USEPA) Storm Water Management Model (SWMM) to evaluate regional differences around the United States in hydrologic and water quality performance of wet-weather controls. Controls are characterised as being limited by peak inflow rate (i.e. any device with little or no storage, such as screens, filters and some proprietary devices) or by storage capacity (e.g., ponds, tanks). For flow-limited devices, results are presented in the form of percentage of annual runoff volume captured (passing through the device) for a given inflow capacity. For storage-limited devices, results are presented in two forms: percentage of annual runoff volume captured as a function of unit basin size and drawdown (drain) time, and as a percentage of total suspended solids captured, for the same two variables. Regional differences are apparent, driven mainly by variations in rainfall patterns around the country.     

THEORETICAL STUDY OF A NEW MATERIAL FOR FILTERS: AEROGELS

Aerogels are highly porous materials made by removing the liquid phase of a dilute suspension of solids by taking off the vapor under super-critical temperature and pressure conditions. The aerogel structure has a skeleton of nanometer-size elements forming pores that are tens of nanometers in dimension. In some cases the structure of the aerogel arises from clusters having fractal geometry. The collection efficiency and pressure drop for such material is predicted here from models in the literature. A quality factor is used to compare aerogel material with other filter materials. The quality factor relating gas filtration efficiency with pressure drop is predicted to be unusually high for these materials in comparison with other common fibrous filter media, predicting lower flow resistance for aerogels at equivalent particle collection efficiency levels.     

Fuel modelling in fast reactor whole core accident calculations

Transient fuel pin behaviour and fuel motion models are of major importance for the analysis of the initiation phase of unprotected whole-core LOF and TOP accidents in LMFBRs. The role played by these models is highlighted by discussing LOF and TOP accident sequences. This is followed by an overview of present whole-core fuel pin behaviour and fuel motion models and also a critical evaluation of these models.     

Pesticide monitoring programme of the Ministry of Health of Brazil

The structure of the recently introduced Brazilian government programme for monitoring pesticide residues in six major agricultural products is described. Residues found from the analysis of samples of tomatoes and strawberries are discussed in detail. The much greater frequency of detection of pesticide residues, many of which are not approved for use in Brazil, in produce being sold on the domestic market, as opposed to that produced for export, is of major concern. It is perceived that this new monitoring programme will become permanent and be used to underpin enforcement actions that will need to be taken to reduce the numbers of incidents of illegal residues occurring, particularly in fresh fruits and vegetables.     

The wear behaviour of oxide ceramics-A Review

The paper reviews the wear behaviour of oxide ceramics. Wear maps are considered and consequently mild and severe wear are defined. Since the use of ceramics in engineering applications require operation in the mild wear regime, the paper concentrates on mild wear mechanisms, but also considers factors which control the transition to severe wear. Within the mild wear regime, the formation of tribofilms are discussed and the manner in which dislocation activity leads to the wear transition is considered. The wear of so-called ceramic nanocomposites, for which no time dependent wear transition has yet been observed, is considered and the reasons for enhanced performance discussed. The role of transformation toughening in zirconia ceramics is considered in detail, and reasons for the generally poor wear response of these materials defined.