Effect of hydrogen addition using on-board alkaline electrolyser on SI engine emissions and combustion

In this study, an electrolyser was used to supply hydrogen to the SI engine. Firstly, the appropriate operation point for the electrolyser was determined by adjusting the amount of KOH in the electrolyte to 5%, 10%, 20% and 30% by mass, and applying 12 V, 16 V, 20 V, 24 V and 28 V voltages. Tests were first carried out with the gasoline without the use of an electrolyser, followed by operating the electrolyser at the appropriate point and sending obtained H₂ and O₂ to the engine in addition to the gasoline. The SI engine was operated between 2500 rpm and 3500 rpm engine speeds with and without hydrogen addition. Cylinder pressure, the amount of gasoline, H₂ and O₂ consumed by the engine and the emission data were collected from the test system at the aforementioned engine speeds. Furthermore, indicated engine torque, indicated specific energy consumption, specific emissions and HRR values were calculated. According to the results obtained, improvement in ISEC values was observed, and CO and THC values were improved by up to 21.3% and 86.1% respectively. Even though the dramatic increase in NO_x emissions cannot be averted, they can be controlled by equipment such as EGR three-way catalytic converter.     

Design and model confirmation of the intermediate scale VolturnUS floating wind turbine subjected to its extreme design conditions offshore Maine

Floating offshore wind turbines are gaining considerable interest in the renewable energy sector. Design standards for floating offshore wind turbines such as the American Bureau of Shipping (ABS) Guide for Building and Classing Floating Offshore Wind Turbine Installations are relatively new and few if any floating wind turbines have yet experienced the prescribed design extreme environmental conditions. Only a few pilot floating turbines have been deployed in Europe and Japan. These turbines have been designed for long return period storm events and are not likely to see their extreme design conditions during early deployment periods because of the low probability of occurrence. This paper presents data collected for an intermediate scale floating semi‐submersible turbine intentionally placed offshore Maine in a carefully selected site that subjects the prototype to scale extreme conditions on a frequent basis. This prototype, called VolturnUS 1:8, was the first grid‐connected offshore wind turbine in the Americas, and is a 1:8 scale model of a 6 MW prototype. The test site produces with a high probability 1:8 scale wave environments, and a commercial turbine has been selected so that the wind environment/rotor combination produces 1:8‐scale aerodynamic loads appropriate for the site wave environment. In the winter of 2013–2014, this prototype has seen the equivalent of 50 year to 500 year return period storms exercising it to the limits prescribed by design standards, offering a unique look at the behavior of a floating turbine subjected to extreme design conditions. Performance data are provided and compared to full‐scale predicted values from numerical models. There are two objectives in presenting this data and associated analysis: (i) validate numerical aeroelastic hydrodynamic coupled models and (ii) investigate the performance of a near full‐scale floating wind turbine in a real offshore environment that closely matches the prescribed design conditions from the ABS Guide. Copyright © 2015 John Wiley & Sons, Ltd.     

Regional Flood Frequency Analysis in Tunisia: Identification of Regional Distributions

Best-fit distributions of floods in Tunisia are determined based on L-moment diagram and statistical tests. GEV and GLO distributions provided the best fit to seven and three regions of Tunisia respectively. In each homogeneous region, hierarchical approaches and regression models were developed for gauged and ungauged watersheds. The first two parameters of the distributions (GEV and GLO) were estimated from measured data while the third parameter was represented by the regional average value weighted by the record length of all stations in the region. The obtained parameters were correlated to the catchment size. Quantiles obtained by the proposed models were compared with those obtained using local conventional models. Statistical tests showed that the proposed models provided a much better agreement with observed floods than any of the conventional methods generally used in Tunisia.     

Complete dynamic modeling and approximate state space equations of the flexible link manipulator

This work treats the problem of dynamic modeling and state space approximation for robotic manipulators with flexibility. Case studies are planar manipulators with a single flexible link together with clamped-free ends and tip mass conditions. In this paper, complete dynamic modeling of the flexible beam without premature linearization in the formulation of the dynamics equations is developed, whereby this model is capable of reproducing nonlinear dynamic effects, such as the beam stiffening due to the centrifugal and the Coriolis forces induced by rotation of the joints, giving it the capability to predict reliable dynamic behavior. On the other hand, in order to show the joint flexibility effects on the model dynamic behaviors, manipulator with structural and joint flexibility is considered. Thus, a reliable model for flexible beam is then presented. The model is founded on two basic assumptions: inextensibility of the neutral fiber and moderate rotations of the cross sections in order to account for the foreshortening of the beam due to bending. To achieve flexible manipulator control, the standard form of state space equations for a flexible manipulator system (flexible link and actuator) is very important. In this study, finite difference method for discretization of the dynamic equations is used and the state space equations of the flexible link with tip mass considering complete dynamic of the system are obtained. Simulation results indicated substantial improvements on dynamic behavior and it is shown that the joint flexibility has a considerable effect on the dynamic behavior of rotating flexible arm that should not be simply neglected. The effects of tip mass is proved to be increasing the elastic deformations?? amplitudes and increasing stability.     

Campylobacter contamination in broiler carcasses and correlation with slaughterhouses operational hygiene inspection

This study investigates factors associated with Campylobacter contamination of broiler carcasses, using survey data collected from nine Belgian slaughterhouses in 2008 in accordance with a European Union baseline study. Campylobacter were detected in 51.9% (202/389) (95% confidence interval, 46.8%-56.9%) of broiler carcasses. Campylobacter concentration was <10 CFU/g in 49.6% of carcasses, while 20.6% were contaminated with ≥1000 CFU/g. The mean Campylobacter concentration, as calculated by maximum likelihood estimation for left-censored data, was 1.8 log₁₀ CFU/g, with a standard deviation of 1.9 log₁₀ CFU/g. There was statistically significant variation among slaughterhouses in prevalence and concentrations of Campylobacter in their sampled carcasses. Campylobacter prevalence (but not concentrations) was positively associated with increase in broilers age. Both Campylobacter prevalence and concentration were significantly higher in carcasses sampled during June and September (but not in July and August) than carcasses sampled in January. We also investigated the correlation (Spearman’s rank correlation test) between the scores of official control inspections and Campylobacter prevalence for eight out of the nine slaughterhouses. The control inspections were routinely performed by the Belgian Federal Agency for the Safety of the Food Chain, and the concluded inspection scores were used as a general numerical indicator for the status of operational hygiene and quality of management in the slaughterhouses. Ranking of slaughterhouses based on their inspection scores was statistically correlated (Spearman’s correlation coefficient = 0.857) with their ranking based on prevalence of Campylobacter. In the present study we demonstrate how the outcomes from a routine baseline survey could be coupled with other readily available data from national control authorities in order to enable a better insight over Campylobacter contamination status in broiler slaughterhouses. Findings from this work call for subsequent in-depth investigations on technical and hygiene management factors that could impact Campylobacter contamination across broiler slaughterhouses.     

MgO single-crystal as an efficient thermal neutron filter

A formula is given which, for neutron energies in the range 10⁻⁴ < E < 10 eV, permits calculation of the nuclear capture, thermal diffuse and Bragg scattering cross-sections as a function of magnesium oxide (MgO) temperature and crystal parameters. Computer program has been developed to calculate the total neutron cross-section and transmission through mono-crystalline MgO. The calculated neutron transmission and effective attenuation coefficient values for MgO-single crystal at different temperatures are compared with measured ones. An overall agreement is indicated between the formula fits and experimental data. A feasibility study for the use of MgO-single crystal is discussed in terms of the optimum MgO-single crystal thickness, mosaic spread, temperature and cutting plane for efficient transmission of thermal-reactor neutrons, and also for rejection of the accompanying fast neutrons and gamma rays.     

Antioxidant activity of ginger extract in sunflower oil

The antioxidant activity of dichloromethane extract from ginger was evaluated during 6 months of storage of refined sunflower oil at 25 and 45 °C. Free fatty acid (FFA) content, peroxide value (POV) and iodine value (IV) were used as criteria to assess ginger extract as an antioxidant. After 6 months of storage at 45 °C, sunflower oil containing 1600 and 2400 ppm ginger extract showed lower FFA contents (0.083 and 0.080%) and POVs (24.5 and 24.0 meq kg^?1) than the control sample (FFA contents 0.380%, POV 198.0 meq kg^?1). Sunflower oil containing 200 ppm butylated hydroxyanisole (BHA) and butylated hydroxytoluene (BHT) showed FFA contents of 0.089 and 0.072% and POVs of 26.5 and 24.7 meq kg^?1 respectively after 6 months of storage at 45 °C. Similarly, after 6 months of storage at 45 °C, IVs of sunflower oil containing 1600 and 2400 ppm ginger extract were 80 and 92 respectively, higher than that of the control sample (53). However, IVs of sunflower oil treated with 200 ppm BHA and BHT were 94 and 96 respectively after 6 months of storage at 45 °C. These results illustrate that ginger extract at various concentrations exhibited very strong antioxidant activity, almost equal to that of synthetic antioxidants (BHA and BHT). Ginger extract also showed good thermal stability and exhibited 85.2% inhibition of peroxidation of linoleic acid when heated at 185 °C for 120 min. Therefore the use of ginger extract in foods is recommended as a natural antioxidant to suppress lipid oxidation. © 2003 Society of Chemical Industry     

Evaluation of ISO 10272:2006 standard versus alternative enrichment and plating combinations for enumeration and detection of Campylobacter in chicken meat

In the present study, we evaluate the recommended ISO 10272:2006 versus alternative procedures for Campylobacter enumeration and enrichment in naturally contaminated chicken meat samples (n = 49). Three enrichment media were evaluated; Bolton broth, Preston broth and CampyFood broth^® (bioMérieux SA, Marcy l’Etoile, France). In addition, three selective plating agars were compared; modified charcoal cefoperazone deoxycholate agar (mCCDA), CampyFood agar^® (CFA; bioMérieux SA) and Brilliance CampyCount agar^® (BCC; Oxoid, Basingstoke, England). Direct plating on CFA provided the highest number of Campylobacter positive samples (17/49); however this was not statistically different (P > 0.05) from numbers of positive samples recovered by direct plating on mCCDA (15/49) or BCC agars (14/49). Also, there was no significant difference between Campylobacter counts on the three compared media (P > 0.05). The coloured colonies of Campylobacter on CFA and BCC were easier to record and count than those on mCCDA. Enrichment of chicken meat samples in Bolton broth for 48 h and subsequent plating on CFA provided significantly higher (P < 0.05) Campylobacter detection compared to the other broth-agar combinations. Enrichment in Preston broth for 24 h followed by plating on mCCDA gave a higher number of positive samples (20/49) than 48 h enrichment in Bolton broth and plating on mCCDA (15/49). Enrichment in Bolton broth for 48 h followed by plating on CFA recovered 35% of samples below the limit for quantifications (<10 CFU/g, n = 34), as identified by direct plating on mCCDA. Compared to the current ISO method, some alternative combinations of enrichment and agar media could provide significantly better detection and enumeration of Campylobacter in chicken meat.     

Preparation of tungsten oxide nanoporous thin film at carbon ceramic electrode for electrocatalytic applications

The electrodeposition of nanoporous tungsten oxide (WO₃) on the surface of carbon ceramic electrode (CCE) was described. The morphology of the WO₃ modified electrode was characterized by scanning electron microscopy and X-ray diffraction. The modified electrode was utilized as an electrochemical hydrogen peroxide sensor in a low potential with a high sensitivity and selectivity. The role of supporting matrix on the sensitivity of modified electrode was studied. The detection limit of 0.26 μM (S/N = 3) and the sensitivity of 16.8 A M⁻¹ cm⁻² were compared with some other metal oxides hydrogen peroxide sensors. The modified electrode has exhibited good reproducibility, long-term stability and negligible interference of some inorganic and biological compounds.