Dynamic properties of calcareous and siliceous sands under isotropic and anisotropic stress conditions

The strain-dependent dynamic properties of sand are generally described by their relative density and mean effective stress, while the contribution of other factors, like soil origin, mineralogy, grain morphology, and initial stress anisotropy, have not been fully recognized. This paper presents the results of an experimental study on the shear modulus and damping ratio of calcareous and siliceous sands of different origins and their identical grain size distribution and stress-density states. Resonant column and cyclic triaxial tests were conducted on reconstituted samples of these two sands obtained from coastal areas. The significance of the initial effective confining pressure and stress anisotropy on the dynamic properties of the sands is evaluated and compared. It is demonstrated that the small-strain shear modulus of the calcareous sand is more affected by an increase in mean effective confining pressure than the siliceous sand. However, the effect of the initial shear on the secant shear modulus of the sands is unique. Based on the test data, a rigorous correction factor is proposed to account for the influence of the initial stress anisotropy on the small-strain shear modulus of the sands. A comparison between the strain-dependent dynamic properties of the calcareous and siliceous sands reveals that the calcareous sand has a higher secant shear modulus, lower damping ratio, and higher linear and volumetric threshold strain. Since the stress-density states and grain size distribution of the two sands were identical in the experiments, the discrepancy in the dynamic properties can be attributed to other factors, including sand origin, grain angularity, mineralogy, and formation processes, which are not commonly taken into account in the current practice.     

Eutectic Morphology in Alloy Pb – 3.2% Cd – 0.08% Sr for Battery Grids

Metal Science and Heat Treatment - Ageing of supersaturated solid solution in Pb – 3.2% Cd – 0.08% Sr alloy is studied at 20 and 80°C by measuring hardness, and light and scanning...     

Radon emanation from radium specific adsorbents

Pilot studies were undertaken to quantify the total activity of radon that is eluted following no-flow periods from several Ra-226 adsorbents loaded to near exhaustion. The adsorbents studied included two types of barium sulphate impregnated alumina (ABA-8000 and F-1) and Dowex MSC-1 resin treated by either barium hydroxide or barium chloride. In parallel, radium loaded plain activated aluminas and Dowex MSC-1 resin were similarly investigated. The results revealed that radon was quantitatively eluted during the first few bed volumes of column operation after no-flow periods. Although similar radon elution profiles were obtained, the position of the radon peak was found to vary and depended on the adsorbent type. Radon levels up to 24 and 14 kBq dm⁻³ were measured after a rest period of 72 h from radium exhausted Dowex MSC-1 treated with barium chloride and F-1 impregnated alumina with barium sulphate, respectively. The eluted radon values measured experimentally were compared to those calculated theoretically from accumulated radium quantities for the different media. For plain adsorbents, an agreement better than 10% was obtained. For treated resin-types a consistency within 30% but for impregnated alumina-types high discrepancy between respective values were obtained.     

Study of photochemical and sonochemical processes efficiency for degradation of dyes in aqueous solution

The degradation of two commercially available dyestuffs (C.I. Reactive Black 5 and C.I. Disperse Orange 25) by ultraviolet radiation (UV), ultrasonic irradiation (US), UV/H₂O₂ and US/H₂O₂ processes was investigated in a laboratory-scale batch photoreactor equipped with a 55 W immersed-type low-pressure mercury vapor lamp and a sonoreactor with low frequency (42 kHz) plate type transducer at 170 W of acoustic power. The toxicity was also evaluated in acute toxicity studies using Daphnia magna. Results showed that color removal efficiencies by US and US/H₂O₂ processes were negligible for both dyes. Almost complete disappearance of Reactive Black 5 (97.9%) in UV/H₂O₂ process was possible after 5 min of irradiation. The maximum color removal efficiency of Disperse Orange 25 after 10 min of irradiation, however, was only 9.2% and reached a maximum value of 41% after 120 min of irradiation. Pseudo-first order kinetics with respect to dyestuffs concentrations was found to fit all the experimental data. The results clearly showed that both dyes examined were toxic to D. magna and resulted in quite low LC₅₀ values.     

Morphological,mechanical, and rheological studies of PVC/ABS blends in the presence of maleic anhydride

A novel method of enhancing compatibility in PVC/ABS blends is the use of ABS‐grafted‐(maleic anhydride) (ABS‐g‐MAH) as a compatibilizer. In this study, maleic anhydride was grafted onto ABS (initiated by peroxide) in an internal mixer. Grafting degree was determined by a back‐titration method, and certain amounts of the resultant ABS‐g‐MAH were added to PVC/ABS blends during their melt blending in the mixer. The weight ratio of PVC to ABS was kept at 70:30. Evaluation of compatibilization was accomplished via tensile and notched Izod impact tests, scanning electron microscopy (SEM), and rheological studies. According to the SEM micrographs, better dispersion of the rubber phase and its finer size in properly compatibilized blends were indications of better compatibility. Besides, in the presence of a proper amount [5 parts per hundred parts of PVC (php)] of ABS‐g‐MAH, PVC/ABS blends showed significantly higher impact strengths than uncompatibilized blends. This result, in turn, would be an indication of better compatibility. In the presence of 5 php of compatibilizer, the higher complex viscosity and storage modulus, as well as a lower loss modulus and loss factor in the range of frequency studied, indicated stronger interfacial adhesion as a result of interaction between maleic anhydride and the PVC‐SAN matrix. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Production and quality of fish fingers from different fish species

Abstract Production of fish fingers was achieved by using fish species such as sardine (Sardina pilchardus, Walbaum, 1792), whiting (Merlangius merlangus, Linnaeus, 1758) and pike perch (Sander lucioperca, Linnaeus, 1758). Quality changes of battered fish patties during a period of 8 months at –18 °C were investigated. According to the results of microbiological and chemical analysis, fish fingers were found to be within acceptable limits during frozen storage for 8 months. However, sensory analysis showed that, at the end of the frozen storage, fish fingers made from sardine could not be consumed because of rancidity.     

Investigation on the resistance spot-welded austenitic/ferritic stainless steel

In this work, the effect of weld current on joining capability of austenitic stainless steel (AISI 304) and ferritic stainless steel (AISI 430) sheets with application of resistance spot welding process was investigated. Macrostructure, microstructure, microhardness, tensile shear strength, and failure mode of welded materials were evaluated for different weld currents. The values of weld current were 2.5, 3.75, and 5 kA. It was found that when the weld current increased, the nugget size and the weld strength were increased. Two distinct failure modes including interfacial and pullout were observed during tensile shear test. Finally, an adequate weld current was obtained.     

Characteristics of low-level smokers.

Average daily cigarette consumption has decreased, and some evidence suggests that the rate of "some day" smoking has increased; however, relatively little is known about low-level smokers. The present analysis describes and compares low-level versus heavier smokers, using cross-sectional and longitudinal data. Data from the Community Intervention Trial for Smoking Cessation (COMMIT) were used in this analysis. Population-based cross-sectional tobacco use telephone surveys were performed in 22 North American communities in 1988 and 1993, and the prevalence and characteristics of low-level smoking and reasons for quitting are reported from the 1993 prevalence survey. In addition, a cohort of 6,603 smokers was identified in 1988 and interviewed again in 1993 and 2001 to assess patterns of low-level smoking over time and its association with smoking cessation. In 1988, 7.6% were low-level smokers; in 1993, 10.7% were low-level smokers. Compared with heavier smokers, low-level smokers were more likely to be female, older, not married, Black or Hispanic; to have a 4-year college degree; to have no other adult smokers in the household; and to wait longer in the day to have their first cigarette. Low-level smokers also were less likely to report trying to quit because of the expense of smoking or physician advice to quit. They were more likely to try to quit because of trying to set a good example; concern for second-hand smoke; and factors such as bad breath, smell, or the taste of smoking. Those who smoked full-priced premium brands and who worked in a completely smoke-free worksite were more likely to be low-level smokers. Compared with heavier smokers, low-level smokers had similar rates of making a future quit attempt, lower use rates of nicotine replacement therapy, and higher cessation rates. Low-level smokers may be a growing segment of the smoker population and have different characteristics, health risks, and intervention needs compared with their heavier smoking counterparts.     

Weld defect formation in FSWed coppers

This work was undertaken to explore the formation of weld defects in FSWed copper metals via both numerical and experimental approaches. The 4 mm-thick copper sheets were friction stir welded at a tool rotational speed of 710 rpm and tool translational speed of 40 mm/min. Microstructural evaluations were performed on the welded specimens. Also a 3D arbitrary Lagrangian Eulerian numerical model was developed to obtain temperature and material velocity profiles. To this aim, DEFORM-3D was implemented for developing the numerical simulation. Numerical results for temperature values showed good agreement with the recorded experimental data. They also suggest that on the advancing side (AS) of the trailing side, the pin velocity has the minimum amount (zero), and this is the main reason for the formation of tunneling cavity. Experimental results show that a force is created between the reminder of material at the joint and the rim of AS. This force causes a prong of surface material from the AS rim to penetrate into lower parts of weld. It seems that the inadequate pressure (low values of the plunge depth), inadequate surface materials, and the trapped air are the main causes for the formation of the weld defects.