Curing and pyrolysis of cresol novolac epoxy resins containing [2‐(6‐oxido‐6H‐dibenz(c,e)(1,2)oxaphosphorin‐6‐yl)‐1,4‐naphthalenediol]

This study investigates the curing kinetics, thermal properties and decomposition kinetics of cresol novolac epoxy (CNE) with two curing agents, 2‐(6‐oxido‐6H dibenz(c,e)(1,2) oxaphosphorin‐6‐yl)‐1,4‐benzenediol (ODOPN), and phenol novolac (PN). In comparison with the conventional PN system, introducing ODOPN, a phosphorus‐containing bulky pendant group, into CNE increases T_g by 33°C, char yield from 30% to 38%, and LOI from 22 to 31. The DSC curing study reveals that the E_a of the CNE/ODOPN epoxy can be obtained by Kissinger's method. The resulting E_a values indicate that the catalytic effect of EMI is insignificant on CNE/ODOPN but is marked on CNE/PN, whose E_a was reduced from 131.5 to 75.6 KJ/mole. This result may be caused by the fact that the symmetric diol attached to the 1 and 4 positions of the naphthalene ring in ODOPN sets up a steadily resonating structure and inhibits the catalytic action. Further investigating the conversion ratio with curing temperature yielded experimental data that agreed closely with Kaiser's model. The orders of the autocatalyzed reaction, m, and the crosslinking reaction, n, are close to 0.5 and 1.0, respectively, independently of the scan rate. Finally, the TGA decomposition study by Ozawa's method demonstrates that the mean E_a declines with the phosphorus content, because the easy decomposition of the phosphorus compound in the initiation stage facilitates the formation of an insulating layer. However, results in this study further reveal an increasing tendency for E_a with decomposition conversion for an ODOPN/PN mixture with the ODOPN content of over 50%, probably because of the retardation of gas diffusion by the insulating layer of phosphorus compound.     

Lignin‐based polycondensation resins for wood adhesives

Lignin‐based wood adhesives are obtained that satisfy the requirements of relevant international standards for the manufacture of exterior‐grade wood particleboard. Formulations based on low molecular mass lignin and presenting an increase in the relative proportion of reactive points yield better results than the higher molecular mass lignin used in the past. These lignins allow a higher proportion of hydroxymethylation during preparation of methylolated lignins. These lignin‐based adhesives also yield acceptable results at particleboard pressing times that are sufficiently low to be of industrial significance. Lignin‐based wood adhesives, in which a nonvolatile nontoxic aldehyde (glyoxal) is substituted for formaldehyde in their preparation, are prepared and tested for application to wood panels such as particleboard. The adhesives yield good internal bond strength results for the panels, which are good enough to comfortably pass relevant international standard specifications for exterior‐grade panels. The adhesives also show sufficient reactivity to yield panels in press times comparable to that of formaldehyde‐based commercial adhesives. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1690–1699, 2007     

Solubility of Propane in Sulpholane at Elevated Pressures

The solubility of propane in sulpholane has been determined at temperatures in the range 298‐403 K at pressures up to 17.6 MPa. The experimental results were correlated by the Peng‐Robinson equation of state, and binary interaction parameters have been obtained for this system. The parameters in the Krichevsky‐Ilinskaya equation were calculated from these interaction parameters.     

Effect of charge density,molecular weight,and hydrophobicity on polycations adsorption and flocculation of polystyrene latices and silica

Adsorption and flocculation behavior of two series of synthetic polycations was investigated in dispersions of silica and polystyrene latices with various particle size and surface charge densities. Polycations of the first series (polydiallyldimethyl ammonium chloride‐PDADMAC) varied in molecular weight only, while polycations of the second series (derivatives of polymethacrylic acid) varied in both molecular weight and hydrophobicity. We have found that maximum adsorbed amount of high molecular weight PDADMAC on latex particles was nearly independent of the surface charge density when the particle size was comparable to the polymer coil dimensions in solution. Both low and high molecular weight PDADMACs were efficient flocculants, although significantly lower amounts of high molecular weight polyelectrolyte were required for the phase separation in the dispersions due to particles aggregation through “charge patch” mechanism. The increase of polymer hydrophobicity leads to higher adsorbed amounts and broadening of flocculation window by polycations of the second series on both substrates. However, no strong enhancement of segment–surface interactions on hydrophobic substrates was observed. Since formation of multilayers upon adsorption was also excluded, the difference in adsorption and flocculation behavior was related to the more compact conformation of hydrophobically associating derivatives in solution and at the interface. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3422–3429, 2006     

Catalytic characteristics of various rubber-reinforcing carbon blacks in decomposition of methane for hydrogen production

Carbon black has recently been reported to act as an effective catalyst for methane decomposition and to exhibit stable catalytic behavior despite carbon deposition, and thus it can be used for CO₂-free production of hydrogen from natural gas. In this work, various carbon blacks with different primary particle size were investigated with respect to methane decomposition under atmospheric pressure from 1123 to 1223 K. Catalytic characteristics, such as activity, activation energy and reaction order, were investigated and compared. It was observed that with decreasing primary particle size (or increasing specific surface area), the specific activity increased and the activation energy decreased. The reaction orders for various pelletized, rubber-reinforcing carbon blacks were 0.6–0.7, about the same regardless of the primary particle size, while they were near 1 for fluffy carbon blacks. Fluffy carbon black showed higher activity and activation energy than the pelletized carbon black of the same primary particle size. Changes of the surface morphology during carbon deposition were observed by TEM. Variations of the number of active sites were discussed in regard of the primary particle size, carbon deposition and binder. The presence of different types of active sites was also suggested.     

Mobile phase composition for resolving whey proteins in reversed-phase high performance liquid chromatography

Reversed-phase high-performance liquid chromatography was successfully developed for the simultaneous and rapid separation for the main whey proteins, α-Lactalbumin and β-Lactoglobulin. This method consisted of a linear gradient of the two mobile phases of 0.1% trifluoroacetic acid in water and 0.1% trifluoroacetic acid in acetonitrile. The total run time for this separation was approximately 30 min, and α-Lactalbumin was eluted followed byβ- Lactoglobulin. The injection volume was fixed at 20 μl and the flow rate was 1 ml 1/min. The optimum mobile phase composition and gradient conditions to separate α-Lactalbumin and β-Lactoglobulin (A+B) were experimentally obtained at the 15 μm particle with a pore size of 300 Å on the linear-gradient mode.     

Effects of Acetic Acid on the Crystallization Temperature of Sol–Gel-Derived MgO Nano-Powders and Thin Films

The influences of acetic acid addition to Mg-methoxide on the stability of the precursor and the crystallization behavior of sol–gel-derived MgO nano-powders and thin films were investigated using X-ray powder diffraction, transmission electron microscopy, Fourier-transformed infrared spectroscopy, and thermogravimetry. The addition of acetic acid enhanced the stability of the alkoxide against precipitation. Moreover, during postheat treatment of the gel powders treated with acetic acid, a significantly lowered crystallization temperature (250°C) was observed as compared to the untreated counterpart (350°C). The low-temperature crystallization of MgO, induced by the modification of Mg-methoxide with acetic acid, was related to the decomposition of organics at a lower temperature. These results could be explained in terms of the decrease of the O–R bond strength depending on the increase in the alkyl group size. MgO thin films having a high degree of crystallinity were successfully obtained from the Mg-methoxide treated with acetic acid at 300°C. The low-temperature crystallization of sol–gel-derived MgO thin films showed the feasibility for their application as a protective layer in alternative current plasma display panel cells.     

水热法制备纳米尖晶石型NiFe_2O_4及表征

分别采用水热法、共沉淀法合成了纳米尖晶石型铁氧体—NiFe2O4晶体,对两种方法所合成的样品进行了比较,分析了不同合成方法的优缺点,确定水热法为比较适宜的合成该类复合氧化物的方法,该法合成的NiFe2O4晶体的平均粒径仅为15.9nm,且粒度分布十分均匀。此外,通过对实验结果的测定与分析探讨了影响水热制备的几种可能的因素,确定了水热合成的适宜的沉淀剂为NaOH溶液,水热合成适宜的温度为200℃。     

Compatibility of polysaccharide/maleic copolymer blends. IV. Thermal behavior of hydroxypropyl cellulose‐containing blends

The compatibility of the hydroxypropyl cellulose (HPC) with maleic acid–vinyl acetate copolymer in the solid state was studied by thermogravimetry, thermo‐optical analysis, differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and optical microscopy. It was established that physical interactions are prevalent in blends with a high content of HPC, whereas chemical interactions predominate in blends with a medium and low content of HPC. By increasing the temperature, the thermochemical reactions are favored. Thermal properties are dependent on the mixing ratio of the components. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2585–2597, 2003     

Effects of hygrothermally decomposed polyurethane on the curing and mechanical properties of carbon black‐filled epoxidized natural rubber vulcanizates

Hygrothermally decomposed polyurethane (HD‐PUR) was mixed up to 20 phr in epoxidized natural rubber (with 50 mol % epoxidation; ENR50) recipes, and the curing and mechanical behaviors were studied. Mechanical testing of the ENR50/HD‐PUR vulcanizates determined the tensile, tear, compression‐set, hardness, abrasion, hysteresis, and resilience properties. No significant changes were observed in the tensile properties with the incorporation of HD‐PUR. The ENR50 compounds showed an increase in compression set with increasing HD‐PUR content. Rubbers cured by a semi‐efficient vulcanization system gave the best overall performance. A further improvement in curing and mechanical properties was achieved by the carbon black grade N330 being replaced with a more active grade (N375). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2265–2276, 2002