Reduction of optical beat interference using gain-saturated RSOA in upstream WDM/SCM optical links

A new scheme for reducing optical beat interference (OBI) noise in optical network units is proposed for subcarrier multiplexing-based access network applications. The optical spectrum of the transmit lasers is broadened by using a radio frequency (RF) clipping tone with a modulation depth greater than one. This reduces the impact of the OBI noise. The distortions caused by an RF clipping tone are also suppressed by introducing a gain-saturated reflective optical amplifier, which shows the characteristics of high-pass filter. The proposed scheme has been verified by measuring the error vector magnitude of 16QAM signal with 20 Mbps. Error-free transmission has been achieved even when the light of OBI-noise-causing lasers is stronger than that of the signal laser by 7 dB     

Cu—Zn—Al系合金热弹性马氏体相变的热滞

本文通过热处理工艺及添加第四组元研究了Cu－Zn－Al系记忆合金的相变热滞。结果表明，淬火冷却速度影响合金的相变热滞大小，随着母相时效时间的延长，马氏体相变热滞变大．Mn元素的加入可以减小CU－Zn－Al合金相变热滞．     

屏蔽暂堵反排解堵效率的实验分析

在一定实验条件下，屏蔽暂堵的反排解堵效率随压差、温度的增大而增大，反排解堵在很短的时间内就可完成。一般的反排解堵率都在60％以上，但反徘不能完全解堵。     

Interdiffusion behavior of Hg in HgTe/CdTe superlattices grown on Cd0.96Zn0.04 Te (211)B substrates by molecular beam epitaxy

Double-crystal x-ray rocking curve (DCRC) and secondary-ion mass-spectroscopy (SIMS) measurements have been performed to investigate the effect of rapid thermal annealing on the interdiffusion behavior of Hg in HgTe/CdTe superlattices grown on Cd_0.96Zn_0.04Te (211)B substrates by molecular beam epitaxy. The sharp satellite peaks of the DCRC measurements on a 100-period HgTe/CdTe (100Å/100Å) superlattice show a periodic arrangement of the superlattice with high-quality interfaces. The negative direction of the entropy change obtained from the diffusion coefficients as a function of the reciprocal of the temperature after RTA indicates that the Hg diffusion for the annealed HgTe/CdTe superlattice is caused by an interstitial mechanism. The Cd and the Hg concentration profiles near the annealed HgTe/CdTe superlattice interfaces, as measured by SIMS, show a nonlinear behavior for Hg, originating from the interstitial diffusion mechanism of the Hg composition. These results indicate that a nonlinear interdiffusion behavior is dominant for HgTe/CdTe superlattices annealed at 190°C and that the rectangular shape of HgTe/CdTe superlattices may change to a parabolic shape because of the intermixing of Hg and Cd due to the thermal treatment.     

蒙特卡罗方法在空间辐射制冷器理论分析及热设计计算中的应用

介绍了二级抛物面型辐射制冷器的热物理模型及用蒙特卡罗方法数值模拟解决其热流理论和辐射热耦合表面（漫发射、镜反射）辐射热交换的处理方法。     

The crystal structure of an Fe-superoxide dismutase from the hyperthermophile Aquifex pyrophilus at 1.9 A resolution: structural basis for thermostability

The incidence of stress fractures is increasing among competitive and recreational athletes as well as among children and the elderly. By understanding the continuum of bone's response to stress and maintaining an appropriate index of suspicion, the health care provider can diagnose these injuries appropriately. An accurate history and examination is essential and will differentiate stress fractures from other stress reactions. The more common stress fractures are discussed.     

PC／PET共混物的非等温结晶动力学

采用等速变温ＤＳＣ法对ＰＣ／ＰＥＴ共混体系的非等温结晶动力学进行了研究，结果表明，从玻璃态结晶时，随着ＰＣ含量的增加，ＰＥＴ组分的结晶速率先增加后降低。耐从熔体结晶时，体系的结晶速率随着ＰＣ含量的增加而增加，讨论了ＰＣ对ＰＥＴ组分结晶过程的影响。     

Self-aligned offset gated poly-Si TFTs with a floating sub-gate

We have fabricated a self-aligned offset-gated poly-Si thin film transistor (TFT) by employing a novel photoresist reflow process. The gate structure of the new device is consisted of two unique patterns: A main-gate and a sub-gate. The new fabrication method extends the gate-oxide over the offset region. With the assistance of the sub-gate and reflowed photoresist a self-aligned offset region is successfully obtained due to the offset oxide acting as an implantation mask. The poly-Si TFT with symmetrical offsets is easily fabricated and the new method does not require any additional offset mask step. Compared with the misaligned offset gated poly-Si TFTs, excellent symmetric electrical characteristics are obtained     

Strain analysis of moving objects using a Fourier transform grid method

There is no good method to measure the shape and the strain distributions of a structure changing with time. We have previously proposed the Fourier transform grid method (FTGM) to measure the three-dimensional shape and surface strain distributions of stationary objects by analysing the two-dimensional grating images recorded with two cameras. In the stereoscopic method, it is very important to determine the accurate geometric parameters of the camera system. In this paper, the positions and the directions of cameras are accurately determined using the FTGM applied to images of a reference object on which a two-dimensional grating is drawn. Applications for analysing shape and strain distributions of vibrating rubber plates and a moving human skin are shown.     

Quasi-static and dynamic crushing behaviors of aluminum and steel tubes with a cutout

Tubular members are commonly used as an energy absorber in engineering structures and many such members have a cutout. In this study, the crushing behaviors of tubes with a cutout are characterized and the effects of cutout on the energy absorption capabilities of these tubes are quantified. Systematic parametric studies were carried out to study the effect of material properties, including yield and ultimate strength of material, strain rate effect, location of cutout, tube length and impact speed on the crushing behaviors and energy absorption capacity of aluminum and steel tubes. First, a numerical model was constructed with a commercial explicit finite element code. It will be first proven that the numerical simulation can produce sufficiently accurate results in an economic manner. Subsequently, the crushing behavior of aluminum and steel tubes with a cutout was experimentally characterized and their energy absorption capacity was evaluated in terms of mean crushing force, peak crushing force and specific energy absorption (SEA). Tubes of various lengths with a cutout located at different locations, subject to both quasi-static and dynamic impact loadings were considered. For steel tubes, the numerical simulation investigated the influence of the strain rate effect and variation in strain hardening ratio of the material. Empirical equations describing the mean and peak crushing forces of aluminum and steel tubes with a cutout were developed using linear and nonlinear regression methods applied to the results obtained from the numerical and experimental studies.