Onset of Marangoni convection in variable-viscosity fluid layer subject to uniform heat flux from below

The onset of stationary Marangoni instabilities in a horizontal fluid layer with free surface deformation and heated from below with a uniform heat flux is considered theoretically using linear stability theory. The explicit solution is obtained and the influences of temperature-dependent viscosity, surface deformability, gravity waves and heat transfer mechanism at the free surface on the stability thresholds are investigated. Small stabilizing effect is observed in fluids with a small viscosity variation while large viscosity variation strongly destabilizes the fluid layer. The stability thresholds are critically dependent on viscosity variation, surface deformation and heat transfer mechanism.     

Integration of interdigital-gated plasma wave device for proximity communication system application

Interdigital-gated AlGaAs/GaAs high-electron-mobility transistor (HEMT) structure was used to investigate the interaction between the drifting carrier plasma waves and electromagnetic (EM) waves. It was shown theoretically that the interaction in the range from microwave to terahertz (THz) at room temperature should produce negative conductance characteristics when the carrier drift velocity slightly exceeds the phase velocity of EM waves. S-parameter reflection measurements were carried out at room temperature for a frequency range from 1 to 20 GHz and a drastic change in conductance was observed at 5 and 10 GHz with the increase of drain–source voltage. Large conductance change over 1000 mS/mm was obtained and it showed a peak at a certain frequency. The peak position could be controlled by changing the pitch size of the interdigital gates. These characteristics can be used for high-frequency applications such as high-speed switching devices although a feature size of our interdigital-gated HEMT device is much larger than conventional HEMT device.     

Oscillatory Marangoni convection in a conducting fluid layer with a deformable free surface in the presence of a vertical magnetic field

Summary. Linear stability theory is applied to the problem of the onset of oscillatory Marangoni convection in a horizontal layer of electrically conducting fluid heated from below in the presence of a vertical magnetic field. The fluid layer is bounded from below by a rigid boundary and from above by a deformable free surface. The critical Marangoni number M _c, the critical wavenumber a _c and the critical frequency _c are obtained for wide ranges of the Prandtl number #E5/E5#₁, the magnetic Prandtl number #E5/E5#₂, the crispation number C _r and the Chandrasekhar number Q. We present numerically a necessary and sufficient condition for oscillatory Marangoni convection to occur.     

Adsorption characteristics of trivalent chromium on palm oil fuel ash

The metal uptake characteristics of ash particles obtained from the combustion of oil palm solid waste (referred to as palm oil fuel ash) are evaluated using trivalent chromium as a model adsorbate. The equilibrium and kinetic properties of Cr(III) are studied in batch stirred-tank experiments. The extent of Cr(III) removal increases with an increase in solution pH. The maximum equilibrium uptake capacity at pH 6 is 0.31 mmol/g of sorbent. A Langmuir isotherm model with pH-dependent parameters accounts very well for the measured equilibrium data. Modeling studies using a second order irreversible reaction model and a pseudo-first order kinetic model indicate that transient profiles obtained experimentally for a range of initial metal concentrations and sorbent dosages are in good agreement with calculated curves of both models. The two kinetic models can be employed for a useful summary of the experimental data so long as their rate coefficients are empirically correlated with the two system variables: initial metal concentration and sorbent dosage. Electronic Publication     

Computerised search for linear binary codes

A computerised search procedure is described for finding new binary codes The method involves the extension of a given known code by annexing a number of parity-check digits to it in such a way that the minimum Hamming distance of the given code is improved. A number of codes found by this procedure have better rates than the best known codes of identical Hamming distance and the same number of information digits; a table of these codes is presented.     

Optimal operation of a distributed energy generation system for a sustainable palm oil-based eco-community

The palm oil industry potentially can be environmentally sustainable through utilizing the vast availability of biomass residues from palm oil mills as renewable energy sources. This work addresses the optimal operation of a combined bioenergy and solar PV distributed energy generation system to meet the electricity and heat demands of an eco-community comprising a palm oil mill and its surrounding residential community. A multiperiod mixed-integer linear programming planning and scheduling model is formulated on an hourly basis that optimally selects the power generation mix from among available biomass, biogas, and solar energy resources with consideration for energy storage and load shifting. A multiscenario approach is employed that considers scenarios in the form of many possible weather conditions and various energy profiles under varying mill operation modes and residential electricity consumption. The proposed approach is demonstrated on a realistic case study for a palm oil mill in the Iskandar Malaysia economic development region. The computational results indicate that biomass-based resource is the preferred renewable energy to be implemented due to the high cost associated with solar PV. As well, load shifting and energy storage can be feasibly deployed for demand peak shaving particularly for solar PV systems.     

Morphology and magnetic characterisation of aluminium substituted yttrium-iron garnet nanoparticles prepared using sol gel technique

Aluminum substituted yttrium iron garnet nano particles with compositional variation of Y(3.0-x) A1(x)Fe5O12, where x = 0.0, 0.5, 1.0, 1.5, 2.0, 2.5 and 3.0 were prepared using sol gel technique. The X-ray diffraction results showed that the best garnet phase appeared when the sintering temperature was 800 degrees C. Nano-crystalline particles with high purity and sizes ranging from 20 to 100 nm were obtained. It was found that the aluminum substitution had resulted in a sharp fall of the d-spacing when x = 2, which we speculated is due to the preference of the aluminum atoms to the smaller tetrahedron and octahedron sites instead of the much larger dodecahedron site. High resolution transmission electron microscope (HRTEM) and electron diffraction (ED) patterns showed single crystal nanoparticles were obtained from this method. The magnetic measurement gave moderate values of initial permeability; the highest value of 5.3 was shown by sample Y3Fe5O12 at more than 100 MHz which was attributed to the morphology of the microstructure which appeared to be homogeneous. This had resulted in an easy movement of domain walls. The substitution of aluminum for yttrium is speculated to cause a cubic to rhombodedral structural change and had weakened the super-exchange interactions thus a fall of real permeability was observed. This might have created a strain in the sub-lattices and had subsequently caused a shift of resonance frequencies to more than 1.8 GHz when x > 0.5.     

Simple preparation and characterization of nickel ferrite nanocrystals by a thermal treatment method

Nickel ferrite nanocrystals were prepared from an aqueous solution containing metal nitrates and poly (vinyl pyrrolidone) (PVP) as a capping agent. To stabilize the particles, they were thermally treated at various temperatures from 623 to 823 K at which calcination occurred, thereby stabilizing the particles, controlling the growth of the nanoparticles, preventing their agglomeration, and creating a uniform distribution of particle sizes. The characterization studies were conducted by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), and transmission electron microscopy (TEM). The crystallization was completed between 723 and 823 K, as revealed by the absence of organic absorption bands in the FT-IR spectra Magnetization measurements were obtained at room temperature by using a vibrating sample magnetometer (VSM), which showed that the calcined samples exhibited ferromagnetic behaviors. Finally, we used TEM images and FT-IR spectra to investigate the same process in the absence of PVP and with various of concentrations of PVP for comparison with the results acquired from using the optimum concentration that was used in this work.     

Mechanical,thermal, tribological,and flammability properties of polybutylene terephthalate composites: Comparing the effects of synthetic wollastonite nanofibers,natural wollastonite,and graphene oxide

Polybutylene terephthalate (PBT) composites were prepared with 1.0 phr synthetic wollastonite nanofibers (SWN), natural wollastonite (NW) and graphene oxide (GO) to study the effect of different fillers on mechanical, thermal, tribological, and flammability properties. The properties of PBT composites are related to the size, structure, and interfacial adhesion of the fillers in PBT matrix. PBT/SWN demonstrated the highest tensile strength and Young's modulus (6% and 9% increment), followed by PBT/NW (1.3% and 7% increment) and PBT/GO (2% decrement and 4% increment). PBT/SWN gave the highest degradation temperature (409°C), followed by PBT/GO (404.7°C). The maximum enhancement in wear resistance (73%) by PBT/SWN and anti-friction performance (26%) by PBT/GO evinced the excellent load-bearing ability of SWN and the great lubricating effect of GO. PBT/NW had the lowest peak heat release rate, smoke, and carbon dioxide production rate. This study shows that PBT composites have great potential in different automotive applications.     

Parametric optimization of NiFe2O4 nanoparticles synthesized by mechanical alloying

In this study, the Taguchi robust design method is used for optimizing ball milling parameters including milling time, rotation speed and ball to powder weight ratio in the planetary ball milling of nanostructured nickel ferrite powder. In fact, the current work deals with NiFe₂O₄ nanoparticles mechanochemically synthesized from NiO and Fe₂O₃ powders. The Taguchi robust design technique of system optimization with the L9 orthogonal array is performed to verify the best experimental levels and contribution percentages (% ρ) of each parameter. Particle size measurement using SEM gives the average particle size value in the range of 59–67 nm. X-ray diffraction using Cu Kα radiation is also carried out to identify the formation of NiFe₂O₄ single phase. The XRD results suggest that NiFe₂O₄ with a crystallite size of about 12 nm is present in 30 h activated specimens. Furthermore, based on the results of the Taguchi approach the greatest effect on particle size (42.10 %) is found to be due to rotation speed followed by milling time (37.08 %) while ball to powder weight ratio exhibits the least influence.